Carboy Accessories

For both carboys and buckets. In our opinion 3 piece airlocks are superior to the triple ripple type in that they can be taken apart and cleaned. However we do sell the triple ripple type (FE371) in case you are use to that type and would like to stay with it. Please Note: Stopper Not Included.

Read more less

Clear glass marbles are a great choice for filling up volume in a small fermenter or oak barrel. Most of us have been in that situation where we have the ideal container we want to use to store our wine, but we just don't have quite enough wine. What are your choices? Either use several smaller containers, buy wine to top up, or try to purge the air space with inert gas. None of these are ideal solutions. Clear glass marbles, free of ink or contamination, are an ideal solution. Use just as much as you need to top up the vessel. When you transfer the wine out, remove your marbles, wash and reuse with your next batch (just don't lose them...) 3 lbs of marbles is enough to displace approximately 1 Liter of liquid. Specifications Count: Approximately 615 Net Weight: 3 lbs Marble Size: 12mm Color: Clear Volume Displaced: About 1.05Qts/1L

Read more less

Plug the hole in other stoppers when moving or shaking the fermenter.

Read more less

For one handed lifting of empty Smooth Necked (not threads) glass carboys. Fits 3, 5, 6, 6.5 gallon smooth neck carboys.

Read more less

A great way to drain your carboys without having to hold them upside down the entire time. These will drain the carboy, although not as well as our BE450 due to how close the mouth of the carboy is to the ground. Note that a carboy can fall out of the stand if left unattended, so please be careful when using this product. Carboys will not fit in this drainer if a carboy handle is on the carboy.

Read more less

Rubber style with two attachments for vinyl blow off hoses (3/8 or 1/2''). For use with our 3, 5, 6, or 6.5 gallon glass carboys with smooth necks. Can also be used on 5 and 6 gallon plastic carboys TIP: Carboy hoods are exceptionally useful for blowoff tubes. Just add 3' of 1/2" racking tubing into a bucket of water as your airlock.

Read more less

The easy way to remove oak chips and cubes from your carboys! These stainless steel perforated tubes will hold 2 ounces of oak (chips or cubes), and can be lowered into the carboy. A small piece of plastic line is tied to the top stopper of the infusion tube, and will allow your carboy stopper to seal tightly while at the same time holding the plastic line securely against the mouth of the carboy. When it is time to remove your oak, grab a hold of the line, remove the stopper, and pull the Oak Infusion Tube out of your beer or wine! Made from stainless steel with silicone stoppers at either end for easy access to either side of the tube. 16" long. Fits carboys 5 gallons and up. Holds 2oz of cubes or chips.

Read more less

Keep your yeast or ML happy and your ferment warm during those cold winter months with this flexible heater made by Fermentap. Using tape to adhere, this flexible heating wrap can be attached directly to your fermenter or can be used to heat the space in a box (or refrigerator) that the fermenter is in. Depending on your configuration and insulation, you can increase the temperature of your wine from 5-20 degrees Fahrenheit. If using carboy or bucket you can attach directly using tape (as seen in photo above.) We recommend electrical tape as it sticks and unsticks the easiest. Heating can be contolled by sticking either the entire wrap or a portion of the wrap to the fermenter. In an open evironment we see a heating differential between carboy and ambient of 10-15 degrees. This differential can be increased by using our carboy bag to insulate a carboy (this has been tested.) To decrease the temperature differential, stick only a portion of the heating wrap to the fermenter. For precise results, we recommend using our temp controller (FE610) and carboy thermowell (FE612) for the ultimate in fermentation temperature contol. For heating small stainless variable volume fermenters and barrels up to 30 gallons a single FermWrap! works great. For volumes of 60 gallons or more, we recommend using two or more FermWraps (we do this in our winery Olin Wines all the time!). With 40 watts of heat spread over two square feet it provides gentle even heating. Draws 40 watts. 115V. Manufactured by Fermentap. Kegland Part number: KL06255 

Read more less

Prevent spillage and overflowing with this uniquely designed funnel with high backsplash. Fits carboy necks.

Read more less

As far as bucket spigots go, this is about as cool as you get. First, unlike many other designs, these spigots don't leak (bonus).  Second it rotates even when sealed so it won't hit the table or floor (duh!). Third the outlet barb has two different diameters so that you can attach  3/8" or 1/2" tubing (thats cool). The interior nut on these spigots also have a unique design where the opening can be rotated up to effectively block sediment if used in a bucket for fermentation or can be rotated down when used in a bottling bucket (genius).  These are also just beefier than other spigots on the market.

Read more less

Mark’s Mark II Keg Washer™ is designed to clean and sanitize large vessels like cornelius kegs and carboys. It is also intended to provide a sanitation container for miscellaneous items such as airlocks, thermometers, tubing, keg fittings, and more. Quiet, Fun, & Easy to Use Very quiet when in use and most importantly speeds up the process of cleaning and sanitizing.    Light in weight.  Easy to store.  Cleans Kegs Cleans and sanitizes a cornelius keg without having to take apart the ball lock fittings, poppets, and dip tubes. You can clean the keg and the dip tube simultaneously using the T adapter. Cleans Tubing Too Cleans tube separately utilizing the pump with the additional barb fittings included.  Cleans Parts Reservoir holds 1.25 gallons of water making it easy to fill and empty with sanitizer.     Saves water and sanitizer.  The unit does not have an on/off switch, you can plug it directly into a wall outlet to operate the pump or plug it into an outlet that is controlled by a switch. Never leave the keg washer unattended when in use. When in use, fill the keg washer up to about 1 inch under the brim. The pump is not self priming, so always make sure the basin is full of water before plugging in the pump. Owner's Manual is included. Please read thoroughly before using. Dimensions of the inside of the washer's reservoir are: 6"L x 12"W x 4"D. Please Note: Product does not include the bucket, carboy, or keg pictured above for display purposes. The pump specs are: 520 GPH 120 Volts AC 40 watts Ceramic shaft, impeller

Read more less

A great carboy hood for a real snug fit. Fits our 3, 5, and 6 gallon glass carboys. Will also fit over our 5 and 6 gallon plastic carboys. Ideal to use if you have a real active fermentation. Add 3' of 1/2" racking tubing to your 3-piece airlock. Take out the bubbler piece to assemble into a blow-off setup.

Read more less

Extra large 3-piece airlock that can hold 50% more sanitizer or water than the standard size (FE370). For both carboys and buckets. In our opinion, 3-piece airlocks are superior to the triple ripple type in that they can be taken apart and cleaned. However, we do sell the triple-ripple (or S-Shaped) type airlock (FE371), in case that's your preference.   Please Note: Stopper Not Included.

Read more less

For replacing worn out washers on most plastic spigots. Compatable with our FE346, FE347 and FE47A.

Read more less

A great funnel for small jobs. This will fit into the necks of most beer and wine bottles, allowing for individual filling. Also works well to fill 2L PET bottles when making soda.  If you make yeast starters in an erlenmeyer flask, pitching that starter just got a whole lot easier! Made in Italy by Ferrari.

Read more less

Universal stoppers have a longer taper to help produce a better fit and a snug seal, and a lip which prevents them from falling into your container. Available with a 3/8 inch hole for an airlock, or solid with no hole. #11-11.5 (large) size is recommended for full size barrels and 14 gallon demijohns.

Read more less

Plastic funnel, top measures 40 cm (15-3/4 in) wide. This mongo funnel is awesome for winemaking or brewing. Internal groove to accept filter screen (BE488). Made in Italy by Ferrari.

Read more less

Universal stoppers have a longer taper to help produce a better fit and a snug seal, and a lip which prevents them from falling into your container. Available with a 3/8 inch hole for an airlock, or solid with no hole. #11-11.5 (large) size is recommended for full size barrels and 14 gallon demijohns.

Read more less

This mesh sleeve is custom made for the FerMonster Plastic Carboy. The plastic ring sits inside the neck of the fermenter, and the lid can be secured on top to make an airtight seal. The ring actually holds onto the neck of the FerMonster so there's no risk of the mesh sleeve falling into the carboy. For brewers, the MonsterMesh is perfect for adding dry hops, oak chips, or fruit additions, which can easily be removed at the scheduled time. For winemakers, in addition to adding grape skins or oak chips, the MonsterMesh is a great way to eliminate head space in the fermenter. Simply fill up the strainer with glass marbles to displace as much wine as needed to fill the volume of the carboy. Made from food grade materials, the #50 mesh will not affect the flavor of the beer or wine, and is temperature rated to 122°F. Designed for multiple uses, the MonsterMesh can be cleaned in the dishwasher and sanitized with the sanitizer of your choice. The MonsterMesh can be used alongside the MiniMesh to hold multiple additions. The MonsterMesh will sit on the neck of the carboy, and the MiniMesh can be inserted through the stopper hole in the lid. This way you can have two different infusions starting or stopping at different times.    

Read more less

A new carboy handle in distinctive blue color that fits our threaded neck 6.5 gal carboys.

Read more less

This mesh sleeve is custom made for the Vintage Shop PET Carboy. The plastic ring sits inside the neck of the fermenter with room for a #10 stopper to be inserted for an airtight seal. The ring actually holds onto the neck of the carboy so there's no risk of the mesh sleeve falling into the carboy. For brewers, the MiniMesh is perfect for adding dry hops, oak chips, or fruit additions, which can easily be removed at the scheduled time. For winemakers, in addition to adding grape skins or oak chips, the MiniMesh is a great way to eliminate head space in the fermenter. Simply fill up the strainer with glass marbles to displace as much wine as needed to fill the volume of the carboy. Made from food grade materials, the #50 mesh will not affect the flavor of the beer or wine, and is temperature rated to 122°F. Designed for multiple uses, the MiniMesh can be cleaned in the dishwasher and sanitized with the sanitizer of your choice. For FerMonster users, the MiniMesh and MonsterMesh can be used simultaneously. The MonsterMesh will sit on the neck of the carboy, and the MiniMesh can be inserted through the stopper hole in the lid. This way you can have two different infusions starting or stopping at different times.    

Read more less

If you keep your carboy in a fermentation locker or other area with little to no head space, every inch counts. We love these low-profile 2-piece airlocks for their compact size and simple design. Instead of a floating plastic "hat", the center piece is molded into the lid. One less thing to clean and misplace! This is the very smallest airlock we sell and works well with fermentations up to 7 gtallons.  Holds approximately 0.4 fl oz (12 ml) Chamber - 1-1/2" tall x 1-3/8" diameter Stem - 1" long Stopper not included

Read more less

The BrewBuilt Neoprene Carboy Sleeve works great for maintaining the internal temperature of your 5, 6, or 6.5 gallon glass carboy. Highly recommended for use with the BrewBuilt Carboy CoolStix. The added insulation will lower the amount of cycles needed to maintain fermentation temperatures and greatly assist in cold crashing. The sleeves are 6 mm thick with stitched piping on the edges for exceptional durability.   SKU Size Height (in.) Diameter (in.) FE329A 5 Gal 14.75 10.75 FE329B 6 Gal 17.25 10.90 FE329C 6.5 Gal 17.50 11.20  

Read more less

If you keep your carboy in a fermentation locker or other area with little to no head space, every inch counts. We love these low-profile 2-piece airlocks for their compact size and simple design. Instead of a floating plastic "hat", the center piece is molded into the lid. One less thing to clean and misplace! This is the larger of the two mini airlocks we sell, holds more liquid than the smallest design, and is good for fermentations volumes up to 13 gallons.  Holds approximately 0.67 fl oz (20 ml) Chamber - 1-5/8" tall x 1-3/4" diameter Stem - 1-1/4" long Stopper not included  

Read more less