Kegging wine can be beneficial in a few different ways! Not only can you serve your wine out of kegs, which is becoming more popular, but kegs can also be used for quickly and easily topping up barrels, blending wines, or stainless steel storage & aging.
Inert Gas & Kegs
Shop By Collection
-
Taprite Dual Gauge Nitrogen Regulator | Argon | Beer Gas Mix | 0-50 PSI Working Pressure | CGA580 Inlet | One Way Shutoff Valve | 5/16" Barb Outlet
A nitrogren regulator used for Nitrogen and Argon - it will fit both tanks. A nitrogen regulator has a higher high-pressure gauge than a CO2 regulator. (The starting pressure in a Nitrogen/Argon tank will be about 2200 p.s.i. as opposed to 800 p.s.i for a CO2 tank.) CGA580. Tap-Rite brand nitrogen regulator. 5/16" barb. For more information on using gas for flushing vessels, please refer to MoreWine!'s Guide to Inert Gas in Winemaking
$129.99
-
Inert Gas Bottle Sparger
Keep your wine from oxidizing! This is one of the most prized possessions of our in-house wine maker. He uses Argon because of its high molecular weight, but CO2 will work. From extended macerations (he gasses before and after laying plastic wrap over the cap) to topping up storage tanks (he uses before setting the floating lid), this is a great way to make sure no excess oxygen is getting into your wine. This can also be used to purge any tank before filling with the wine. Designed to mate with an H550B Quick disconnect installed in the standing end of your 5/16" gas line (H550B and gas line not included).
$44.99
-
Vinyl Beverage Tubing | Rigid | Draft Line | 3/8 in. ID | 5/8 in. OD
3/8 in. ID Beverage Tubing Technical Specifications: 3/8" line provides .20 lbs of restriction per foot. Ideally pounds of resistance should equal pounds of applied pressure. 3/8" line holds 3/4 of an ounce per foot. Made from PVC. Outer diameter of tubing is approximately 5/8"
$2.19
-
Vinyl Beverage Tubing | Rigid | Draft Line | 5/16 in. ID | 9/16 in. OD
5/16 in. ID Beverage Tubing Technical Specifications: 5/16" line provides .40 lbs of restriction per foot. Ideally pounds of resistance should equal pounds of applied pressure. 5/16" line holds 1/2 of an ounce per foot. Made from PVC.
$2.19
-
Vinyl Beverage Tubing | Rigid | Draft Line | 1/2 in. ID | 3/4 in. OD
1/2 in. ID Beverage Tubing Technical Specifications: 1/2" line provides .025 lbs of restriction per foot. Ideally pounds of resistance should equal pounds of applied pressure. 1/2" line holds 1 1/3 of an ounce per foot. Made from PVC.
$5.89
-
Rebuild Kit | O-Rings | Corny Keg
Includes two gaskets for the dip tubes, two for the body connects and one for the lid o-ring. Any keg that has been used for soda in the past should have its gaskets replaced because the soda flavor can never be removed from the rubber. These kits work for Ball lock and most Pin lock kegs.
$4.39
-
Taprite Dual Gauge CO2 Regulator | High Performance Primary Regulator | 0-50 PSI Working Pressure | CGA320 Inlet | One Way Shutoff Valve | 5/16" Barb Outlet
The Taprite is our favorite dual-gauge regulator on the market. We've used them all and this unit represents the best quality at a great price. Key features are the easy hand adjusted pressure adjustment dial, barbed outlet, one way on/off valve, and built in tank connection gasket. Best of all is the consistent pressure regulation. With many regulators the pressure can 'creep' up over time. This unit is a rock. This is the T742HP model where the HP stands for high performance. Won't freeze up when multiple taps are running at once. The built-in gasket where the regulator connects to the CO2 tank, eliminates the constant replacement of fiber washers every time you change out your tank. The one way valve keeps beer from flowing back into the regulator when a keg happens to have more pressure than your regulator is pushing. Hand dial is easily turned to adjust pressure without the need for a screw driver. Optional available gauge cage is the best on the market. Low Pressure gauge reads from 0 to 60 psi. Built by Taprite, an American company. General Regulator Information A regulator controls the flow of CO2 gas that is under pressure. To ensure proper operation, please make sure that when in use your CO2 tank and regulator remain in an upright position. Do not physically modify the regulator in any way. Regulators work best at room temperature. If you use your regulator in the cold it will take up to 4 hours for the adjustment to register. For example: If you are at 10 PSI and you change the pressure to 12 PSI the regulator will move to 14 or 15 PSI over the next 4 hours. Once you have found the correct pressure the regulator will work perfectly fine but it will take some trial and error to get it adjusted. More Tips & Tricks: Are you out of CO2? When the needle reads half way in the red you are about 10% full. You should be able to push another 2-3gallons of beer when your at this amount of remaining gas. What is an ideal serving pressure? For most beers a pressure set at 10-12PSI is the sweet spot. Your beer has to be stored cold from 34-40F for this pressure to work properly. Is your beer serving a lot of foam? Don't panic this is not hard to fix. Your beer line must be 5-8 feet in length for this to work. Turn the black check valve to the close position (as pictured). Release the pressure from your keg's relief valve. Lower the pressure to 6-8psi by turning the flat head screw on the front of the regulator counter clock wise. Open the black check valve releasing CO2 to your keg. Try serving your beer. Is my beer over carbonated? Any beer that is stored under pressure above 12psi will become overcarbonated. If you're trying to speed up the process to carbonate your beer by raising your pressure anywhere from 15-20psi make sure you don't leave your beer at this pressure for more than 2-3 days. If you did this you will need to release all the pressure from the keg before serving and set your serving pressure at 4-6psi depending the carbonation of your beer. After a week you will have to raise your pressure back to the optimum 10-12psi serving pressure.
$87.99
-
Gauge Cage | For Taprite Regulator | Mounting Bolt & Washer Included
Protect a dual gauge regulator from falls. A very worthy investment. If you are moving your tank around with regulator attached, a gauge cage becomes a necessity. While made by Taprite to work with our D1060 and D1070 Dual Gauge Taprite Regulators, it will also work with most other brands. Mounting bolt and washer included.
$27.99
-
KegLand Ball Lock Quick Disconnect (QD) | Gas In | Barbed
White, gas in quick disconnect with barb for gas line. Barb is 1/4". 1/4" or 5/16" beverage tubing is recommended for gas line. Tip N' Trick: Sometimes ball lock fittings are a challenge to quick disconnect "on and off" a cornelius keg. We recommend spraying the body connect on the keg first with a sanitizer solution which acts as a lubricant. When applying the ball lock fitting to the body connect, give a twist and turn to make it easier to connect. We've coined this term "Lube and Turn". Kegland Part Number: KL02943
$6.59
-
KegLand Ball Lock Quick Disconnect (QD) | Beverage Out | Barbed
Black, beverage out quick disconnect with barb for beverage line. Barb is 1/4". 3/16" beverage tubing is recommended. Tip N' Trick: Sometimes ball lock fittings are a challenge to quick disconnect "on and off" a cornelius keg. We recommend spraying the body connect on the keg first with a sanitizer solution which acts as a lubricant. When applying the ball lock fitting to the body connect, give a twist and turn to make it easier to connect. We've coined this term "Lube and Turn". Kegland Part Number: KL02950
$6.59
-
Diffusion Stone - 2 Micron Oxygen Stone
Use this 2 micron oxygen stone with an oxygen source or aeration pump to provide your yeast with oxygen before or during fermentation. Macro-oxygenation, or adding oxygen during the fermentation aids in promotion of yeast growth and general yeast health which results in stronger finishes and fuller flavored wines. In our experimentation, the oxygenation has helped to soften the wine by reducing the sensation of tannins, while simultaneously allowing more fruit to come through. Can also be used for degassing wine with nitrogen. Use with 1/4" ID tubing - D1702. Note: if you are using an aeration pump, we recommend a "deep water" type for aquariums, as these will have the necessary PSI to force the air through the stone and into the juice/must. You can learn more about the use of oxygen during fermentation by reading our Guide to Macro Oxygenation and Fermentation 316 Stainless 1/2" diameter. Stone is 1" in length. Overall length is 1 7/8" Sanitizing your Diffusion / Carb Stone: To properly prepare your stone for use, we recommend you boil the stone portion in water for 3-5 minutes. By heating the stone to boiling temperatures you kill all possible contaminants that may be hidden within the stones micro pores. Using a surface sanitizer is not a guarantee from contamination. Boiling also greatly reduces clogging issues by helping to remove sugar residue. If boiling is not an option, for whatever reason, we recommend the next best, soaking in Star San. Star San will remove a majority of surface contamination/bacteria, but will not sanitize the interior of the stone which may or may not be contaminated. Please note that you do not want to touch the stainless stone portion with your hands. The oils on your fingers can actually clog the small pores in the stone.
$12.99
-
Gas Tubing Assembly - Ball Lock Quick Disconnect (QD) - 5/16 in.
Includes ball lock gas-in quick disconnect (barb), 5 ft of 5/16" ID tubing, and two hose clamps.
$14.99
-
Beer Line Assembly with Quick Disconnect (QD)
Includes ball lock beverage-out quick disconnect (barb), 5 ft of 3/16" tubing, hand held faucet, and two hose clamps.
$15.99
-
Flare Fitting - Washer
You will need this washer anytime you connect flare fittings, except when connecting to our quick disconnects which include a built in washer.
$0.49
-
1/4" Nut & 5/16 Barb
This is a special 1/4" nut and 5/16" barb that will attach to threaded quick disconnects or other 1/4" male flare fittings and allow 5/16" gas tubing to be attached. Stainless Steel barb with a chrome plated Brass nut.
$4.99
-
Gas Manifold - 5/16 in. (Brass)
Manifolds allow you to have one CO2 tank with multiple lines. Each line can be turned off individually without affecting flow to other kegs. Each ball valve contains a check valve that ensures no beer or gas can flow between the two kegs. The barbs are all 5/16", standard for gas line in the beer industry.
$32.99
-
The OxyWand™ Oxygenation Kit - 0.5 Micron
Use the OxyWand™ to infuse oxygen into your must during the start of fermentation to feed yeast and to reduce volatile sulfur compounds (VSC's) with a process called Macro Oxygenation. It is actually very easy to do. Insert the wand, turn on oxygen, and leave it on only while you punch the cap. After three days or when your wine has reached 10% alcohol stop oxygenating. Yeast use the oxygen as a nutrient to produce healthy cell walls which helps to eliminate issues throughout fermentation. Healthy yeast also produce better flavors and produce less Volatile Sulfur Compounds. You can also actually smell the must become fresher and more fruity while oxygenating as VSC's are driven off. Note that in styles like Syrah and Sauvignon Blanc where sulfur compounds are part of the flavor profile you would want to reduce the amount of Macro Oxygenation in frequency and/or duration. Macro Oxygenation also has the benefits of locking up color and rounding tannins. Want to read more? See our paper on our website at https://morewinemaking.com/ articles/Macro_oxygenation_fer mentation. Kit Includes: Adjustable brass oxygen regulator Sanitary air filter 4 ft of tubing Instructions 26" long 0.5 Micron OxyWand™
$59.99
-
Cornelius Poppet | Common | Corny Keg Part
These poppets are the most common poppets that we sell and will fit nearly every used keg that we sell.. Technically it is for Cornelious brand "Spartan" and "Super Champion" kegs. This poppet will also fit Cornelius brand Pin Lock "R" kegs. Each keg uses two poppets.
$6.99
-
CMBecker Ball Lock Quick Disconnect (QD) | Gas In | Flared | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA
This is a high quality plastic quick disconnect made by CM Becker for your gas line. Flare is 1/4" Tip N' Trick: Sometimes ball lock fittings are a challenge to quick disconnect "on and off" a cornelius keg. We recommend spraying the body connect on the keg first with a sanitizer solution which acts as a lubricant. When applying the ball lock fitting to the body connect, give a twist and turn to make it easier to connect. We've coined this term "Lube and Turn".
$7.29
-
CMBecker Ball Lock Quick Disconnect (QD) | Beverage Out | Flared | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA
This is a high quality plastic quick disconnect made by CM Becker for your beverage line. Flare is 1/4" Tip N' Trick: Sometimes ball lock fittings are a challenge to quick disconnect "on and off" a cornelius keg. We recommend spraying the body connect on the keg first with a sanitizer solution which acts as a lubricant. When applying the ball lock fitting to the body connect, give a twist and turn to make it easier to connect. We've coined this term "Lube and Turn".
$7.29
-
Vinyl Beverage Tubing | Rigid | Draft Line | 1/4 in. ID | 1/2 in. OD
PVC tubing for gas and beer lines in kegging systems. 1/4 in inside diameter tubing with thick walls.
$6.09
-
KOMOS® 22 ft³ Nitrogen Tank | Argon Tank | Beer Gas Tank | Premium Aluminum | New | CGA580 Valve | US DOT Approved
Use Nitrogen or Argon for flushing tanks or pushing wine from kegs for topping up barrels or serving Perfect for serving still wine, cold brew coffee, Sangria and premixed cocktails on draft Can be filled with Nitrogen, Argon, or Beer Gas Mix Brand new, high-strength aluminum tank with CGA580 valve Ships empty—fill at a welding shop or swap at your local beer & winemaking supply store Brand new aluminum 22 cubic feet Nitrogen tank made from high strength aluminum alloy and high quality CGA580 valves. Because it is made of aluminum rather than steel you can feel confident that it won’t rust. This is the tank you need for flushing vessels or pushing wine from kegs using either Nitrogen or Argon. Gas flushing is a very useful process for giving added protection to wines by helping to minimize contact with oxygen in your storage containers. Also, wine stored in kegs for either topping up barrels or for serving should be pushed with Nitrogen or Argon rather than CO2 to prevent adding carbonation to your wine (unless you want all your wines to be sparklers!). Generally speaking, we recommend using Argon instead of Nitrogen around your winery, mainly because it is denser than air and so is much more effective when it comes to flushing vessels. Though it is more expensive than Nitrogen, we feel that the added expense is worth it when it comes to protecting our wines. Aluminum tanks are superior to steel because they do not rust. All tanks are shipped empty. To have tanks filled you will want to visit your local welding supply shop. Because you are purchasing a new tank you can choose to either have it filled or to exchange it for a filled tank at your local gas supplier. If you have this tank filled the local gas supplier is responsible for affixing the correct neck label that identifies the gas being put in the cylinder. Tanks should always be stored in an upright position. Features: Made from corrosion resistant, engineered Aluminum Brushed finish Thick, durable cylinder walls DOT approved New high quality CGA-580 valve Light weight compared to steel tanks Rated to 2216 PSI service / 3360 PSI test pressure PSI (allowing for Nitrogen fill) Can also be filled with Argon or Beer Gas Mix (Nitrogen/CO2) NOTE: You will need at Nitrogen/Argon Regulator to go with this tank, a standard CO2 regulator will not work.
$110.99
-
Cornelius Keg Lid (New)
We love these keg lids as either a replacement or an upgrade to the stock lid featured on many homebrew kegs. Most homebrew kegs feature a straight, parallel bale that sits extemely close to the lid when in the closed position. So close that it can be hard to get a finger or two under the bale to open it. The arms on this lid bend outward creating a nice, easy-to-grip handle to open and close the bale. For use with Torpedo, Cornelius, and Firestone kegs. Comes with a pull-ring pressure relief valve and o-ring. PRV rated to 85 psi.
$19.99
-
Replacement PRV | Pull Ring Pressure Relief Valve | Gray | 100 PSI
The most common relief valve. Fits most Cornelius and Firestone style kegs. Long body with spring with gray top and pull ring. Max. pressure rating: 100 psi Kegland Part Number: KL03070
$8.79
-
Corny Keg Lid O-Ring | Silicone | Corny Keg Part
Round silicone O-rings for Cornelius keg lids.
$4.39
-
CO2 Tee | Stainless | 5/16 in Barb
An inexpensive way to split your co2 gas line to multiple taps. Works with 5/16" tubing best, barbs on this CO2 Tee are 5/16", use hose clamps to secure. A quick tip is to put the end of the tubing in 100-120F water for a minute to soften the tubing. We suggest work gloves when putting tubing onto this product as the ends can be sharp.
$5.49
-
Vinyl Beverage Tubing | Rigid | Draft Line | 5/16 in. ID | 9/16 in. OD
PVC tubing for gas and beer lines in kegging systems. 5/16 in inside diameter tubing with thick walls.
$4.89
-
Gasket | Dip Tubes | Corny Keg Part
Slide gasket onto dip tube and then place dip tube back in keg. 5/16" ID with a 7/64" cross section. Made of FDA BUNA N
$0.49
-
CMBecker Ball Lock Quick Disconnect (QD) | Gas In | Barbed | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA
This is a high quality plastic quick disconnect made by CM Becker for your gas line. Barb is 1/4". 1/4" or 5/16" beverage tubing is recommended for gas line. Tip N' Trick: Sometimes ball lock fittings are a challenge to quick disconnect "on and off" a cornelius keg. We recommend spraying the body connect on the keg first with a sanitizer solution which acts as a lubricant. When applying the ball lock fitting to the body connect, give a twist and turn to make it easier to connect. We've coined this term "Lube and Turn".
$7.29
-
Pressure Gauge | Low Pressure (0-30 psi) | CO2 or Nitrogen Regulator | 1/4" MPT Right-Hand Thread
Replacement low pressure gauge for CO2 or Nitrogen regulator - used to determine how much pressure you're allowing out of the regulator. RHT
$15.99
-
Pressure Gauge | Low Pressure (0-60 PSI) | CO2 or Nitrogen Regulator | 1/4" MPT Right-Hand Thread
Replacement CO2 regulator 60 psi gauge for setting dispense pressure. RHT
$12.99
-
The OxyWand™ - 2 Micron
The Oxywand can be used during red wine fermentations to help promote yeast health while simultaneously reducing undesireable sulphur based compounds. The OxyWand™ comes with the 24" stainless wand with turned end, a 2 micron diffusion stone, and the nut / washer required to connect the two. The assembly is 26" long and will easily reach the bottom of glass carboys, dropped into stainless conicals, Speidel fermenters, etc. To learn more read our MoreManual called Oxygen & Fermentation available on our website. For kit winemaking the Oxywand can also be used to degas wine by pumping in nitrogen to strip out excess CO2 left in solution.
$29.99
-
Megamouth Torpedo Keg | Ball Lock Keg | Stainless Steel Corny Keg
The Megamouth Torpedo Kegs are by far the easiest to clean and maintain out of any ball lock homebrew keg you'll find. With an extra-large lid opening, even the buffest of homebrewer (we hear they do exist!) will have no trouble reaching in for a good scrub when it kicks—no expensive keg washing contraptions needed! The Megamouth makes for an excellent pressurizable fermentation vessel and is the ideal choice for brewers who prefer to add dry hops and other flavoring ingredients directly to the keg. The brand new patented design, D794,899, of the Torpedo Keg gives you a high quality keg with features that a dedicated home brewer will appreciate. The machine welds on the Torpedo Keg exceed our standards for quality. There are no nooks and crannies for contaminant to get lodged in. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer. These kegs can be stacked on top of each other with the Ball Lock quick disconnects still attached. They feature rolled stainless steel handles that are comfortable to grab. "In" and "Out" are etched near the keg posts for a quick and mistake-free set up when you are connecting lines in a refrigerator or kegerator. Considering the price and quality, the Torpedo Keg is an amazing value! Mouth opening is 5.8" L x 4.8" W. Dimensions: Height (in.) Diameter (in.) 3 Gal 13.4 11.4 5 Gal 17.9 11.4 6 Gal 20.5 11.4 10 Gal 30.3 11.4
$169.99
-
Torpedo Keg | Ball Lock Keg | Stainless Steel Corny Keg | Low2 Keg Lid O-Ring | Superior Oxygen Barrier Properties
Due to high demand, some of these items are currently out of stock but available for pre-order. Please check status notes below when selecting a size option to see if it is In Stock or tagged as PreBook. We will automatically ship this to you when we receive more inventory. Brand new, all-stainless construction ball lock keg Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Set your sights on a brand new Torpedo Keg! The patented, D794,899, sleek all-stainless design represents the pinnacle of quality in ball lock homebrew kegs. With features like welded stainless handles, the ability to stack with fittings in place, amazing quality and a great price we think these kegs will become the standard by which other kegs are measured. Quality First The first thing we at MoreBeer! check out is interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. These kegs are machine welded and exceed our standards for quality. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. In and Out is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Taking your keg on the go? Don't leave home without a custom fitted Torpedo Keg Sleeve! Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions: Height (in.) Diameter (in.) 1.5 Gal 10.25 9 2.5 Gal 14.75 9 5 Gal 23 9 Please Note: These are about 1/2" wider than standard Ball Lock Cornelius Kegs. Need something a bit slimmer? Check out our lineup of Slimline Torpedo Kegs!
$119.99
-
The OxyWand™ 0.5 Micron
The Oxywand can be used during red wine fermentations to help promote yeast health while simultaneously reducing undesireable sulphur based compounds. The OxyWand™ comes with the 24" stainless wand with turned end, a .5 micron diffusion stone, and the nut / washer required to connect the two. The assembly is 26" long and will easily reach the bottom of glass carboys, dropped into stainless conicals, Speidel fermenters, etc. To learn more read our MoreManual called Oxygen & Fermentation available on our website. For kit winemaking the Oxywand can also be used to degas wine by pumping in nitrogen to strip out excess CO2 left in solution.
$29.99
-
1/4" Aluminum Gas Manifold
Manifolds are a great way to have one CO2 tank supply multiple kegs. This manifold is made from aluminum, brass, and stainless. It also works up to 100 psi and includes 1/4 in ball valves with built in check valves. Another ball valve can be added to the end of the manifold for an additional gas line. Multiple manifolds can be linked up with a 1/4" nipple (D1820B). Features: 1/4" BSP ball valves 1/4" barbs Rated up to 100 psi Screw holes for easy mounting Optional additional port on the end SKU Overall Length D1802 5-1/2 in. D1807 7-3/8 in. D1811 9-5/8 in. D1813 11-1/2 in. D1816 13-1/2 in. The above measurements are from the tip of the brass barb to the plug on the opposite end. Each manifold measures approximately 3.5" from the mounting holes to the tip of the valve. Kegland Part number: KL02554
$26.49
-
KegLand Ball Lock Quick Disconnect (QD) | Beverage Out | Stainless Steel | Flared
This is a ball-lock type quick disconnect that is constructed from stainless steel for lifetime longevity. This product is for the Black Beverage Out connection on the right, for the White Gas In connection, see our KEG734. 2 1/8" H Please note: the outer bushing on the disconnect is made from chrome-plated brass. All parts that come into contact with liquid are stainless. Kegland Part Number: KL03018
$18.99
-
CMBecker Ball Lock Quick Disconnect (QD) | Beverage Out | Barbed | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA
This is a high quality plastic quick disconnect made by CM Becker for your beverage line. Barb is 1/4". 3/16" beverage tubing is recommended. Tip N' Trick: Sometimes ball lock fittings are a challenge to quick disconnect "on and off" a cornelius keg. We recommend spraying the body connect on the keg first with a sanitizer solution which acts as a lubricant. When applying the ball lock fitting to the body connect, give a twist and turn to make it easier to connect. We've coined this term "Lube and Turn".
$7.29
-
KegLand Ball Lock Quick Disconnect (QD) | Beverage Out | Flared
Black, beverage out quick disconnect with male flare fitting made for Cornelius type kegs. 1/4 inch male flare (MFL) threaded fittings make it easy to connect a variety of hardware pieces and connectors. MFL fittings are more versatile than barbed fitting, but they must be tightened down properly or they can leak. Barbed fittings are also available. Kegland Part Number: KL02974
$6.59
-
KegLand Ball Lock Quick Disconnect (QD) | Gas In | Flared
White, gas in quick disconnect with male flare fitting made for Cornelius type kegs. 1/4 inch male flare (MFL) threaded fittings make it easy to connect a variety of hardware pieces and connectors. MFL fittings are more versatile than barbed fitting, but they must be tightened down properly or they can leak. Barbed fittings are also available. Kegland Part Number: KL02967
$6.59
-
Vinyl Beverage Tubing | Rigid | Draft Line | 3/16 in. ID | 7/16 in. OD
PVC tubing for gas and beer lines in kegging systems. 3/16 in inside diameter tubing with thick walls.
$4.29
-
CO2 Tee - Rigid Plastic
Simple Tee's that work great with 5/16" ID tubing. Made in the USA by Kent.
$2.49
-
5 Gal CoolBrew Corny Keg Cooler
Keep your kegs insulated with the new CoolBrew Keg Coolers. Specifically built for Cornelius kegs, these jackets will preserve your precious brew for longer when you take a keg out to share with friends. They come a little oversized to give you extra room for ice or ice packs. This one is perfectly sized for 5 gallon Cornelius kegs. Features: Made from durable polyester Comes with a shoulder strap for easy transport Insulation can keep kegs cold for hours Zipper on top provides easy access to tap and QDs 100% waterproof 26.5 in. Tall x 12 in. Diameter
$59.99
-
Curved Dip Tube | Beverage Out | Ball Lock Kegs Only | Corny Keg Part
For Cornelius style ball lock kegs with curved dip tube. Stainless Steel.
$16.49
-
KOMOS® Gas Manifold | Aluminum | 1/4 in. Flare
The KOMOS gas manifold features 1/4" flare gas inlet and check valves for much more flexibilty when choosing your draft line. Use 1/4" or 5/16" gas line with the appropriate Flare Fitting Set (KEG607 or KEG640), or use EVABarrier Draft Tubing with the appropriately sized Duotight fitting (DUO106 or DUO120). The check valves can also be replaced with a Ball Lock Post Bulkhead, allowing for the use of a gas-in ball lock jumper line as a quick connect option. If more than 4 outlets are needed, join multiple manifolds together with this 1/4" Nipple. Features: 1/4" Flare connections 1/4" BSP ball valves Rated to 100 psi Wall mount holes Made from aluminum, brass, and stainless steel Size Overall Length 2-way 5.25" 3-way 7.25" 4-way 9.25" The above measurements are from the tip for the brass flare inlet to the plug on the opposite end. Each manifold measures approximately 3.5" from the mounting holes to the tip of the valve.
$26.99
-
Torpedo Keg | Ball Lock Keg | Stainless Steel Corny Keg | 15 gal.
The newest addition to the Torpedo Keg arsenal! This ball lock keg has the same great features and superior quality as its predecessors, and will allow large-scale homebrewers to fit their entire batch into a single keg. These kegs are laser welded by an ISO certified commercial keg manufacturer, so you won't find any nooks or crannies for contaminants to hide. Made with rolled stainless steel handles that are comfortable to grab. "In" and "Out" are etched near the keg posts for a quick and mistake-free set up when connecting lines in a refrigerator or kegerator. The 10 and 15 gallon kegs can be stacked on top of each other with ball lock fittings still attached. Considering the price and quality, this Torpedo Keg is an amazing value! Specifications: Total Capacity: 15.2 gal. Max Pressure: 130 psi PRV Rating: 85 psi Height: 24.75" Diameter: 16.05" Made from 304 Stainless Steel
$269.99
-
Torpedo Keg Sleeve
Neoprene keg sleeves for standard Torpedo Kegs. For the Slimline series sleeves, see KEG651. 6mm thick. The 5-gallon sleeve is also compatible with 1/6 bbl or sixtel commercial sanke kegs.
$19.99
-
Duotight In-Line Regulator | Built-In Pressure Gauge | 0-60 PSI | Liquid & Gas Compatible | 8 mm Duotight
The Duotight In-Line Regulator works with both gas and liquid. Easily adjust the flow can be adjusted with the yellow adjustment knob. 8 mm Duotight fittings at both inlet and outlet make this unit perfect for use with EVABarrier 8 mm OD tubing (D1717 or D1718). Features an integrated pressure gauge so you can quickly and easily dial in your pressure setting. The analog gauge is removable and can be swapped out with a gauge of a different pressure range or it can be swapped out for the Digital Mini Pressure Gauge. Stepping Down Pressure The ideal regulation scenario occurs when the inline regulator steps down the output pressure to at least 10 PSI less than the inlet pressure. For example, if the inlet pressure is 30 PSI, the regulator effectively manages a range from 0–20 PSI on the output side ensuring optimal performance and stability. Ideal regulation scenario (10 PSI less than inlet pressure) Example of 30 PSI inlet translating to 0–20 PSI output Specifications: Made from food grade acetal Stainless screws Easily disassembles for cleaning 8mm (5/16") Duotight fittings at both ends Interchangeable pressure gauge Gauge reads from 0-60 psi Made with quality EPDM seals Wall mountable WARNING: Do not exceed gauge pressure. Exceeding the pressure range will damage the gauge. Kegland Part number: KL15035
$19.49
You have seen 48 out of 113 products