Cleaning equipment is probably the most important piece of equipment a winemaker can own! This is because prevention is the best way to handle a spoilage problem. A great deal of most microbial problems in our wines can be avoided by keeping the winery clean and maintaining a protocol of cleaning and sanitizing every time you work in the winery. However, we can only sanitize a surface if it is clean, so MoreWine! offers the following brushes, scrub pads, and cleaning balls to help get the job done.
Complete information on cleaning & sanitizing can be found in our Cleaning & Sanitizing manual.
Cleaning Equipment
-
Italian Wine Bottle Brush
Italian-made wine bottle brush. You might like this design because it has a tuft on the end that is good at getting the corners of your bottles. Customers also like this brush for the easier entry and exit into the bottle neck compared to other brushes. Plastic handle is a little easier to grab as well. Made in Italy 18" long x 2.25" Diameter.
$4.09
-
Line Brush - 3/8 in. x 48 in.
A brush everyone should have. Clean out any 3/8" ID transfer/blow-off tubing.
$7.69
-
Cleaning Ball for Tubing (1/2 in. - 2.5 in. ID)
Cleaning balls are super handy for scrubbing the inside of your transfer tubing. Simply insert into the end of the suction-side tubing connected to your pump and turn the pump on. Be careful not to draw the ball in to the pump head. For the outlet side of the pump, disconnect the tubing from the pump, insert the ball, reattach and turn on the pump. for best results repeat several times on each side. If stains persist, fill your lines with a warm PBW solution and let sit for about an hour before scrubbing again. Available in sizes for 1/2", 1", 1.5" and 2.5" inner diameter tubing.
$6.59
-
White Scrub Pads (3)
These pads are made of soft, woven fibers making them great for equipment cleaning. They will not scratch most surfaces and are the best choice for cleaning stainless steel. Also good for chrome, copper, and porcelain. Sold in packs of three.
$12.99
-
Line Brush - 1/2 in. x 48 in.
Great for cleaning 1/2" transfer tubing, especially if the line was used with the carboy hood as a blow off.
$9.99
-
Stainless Steel Bottle Washer
Clean out dirty bottles with ease. Our stainless bottle washer creates a jet-style stream that penetrates build-up in bottles or carboys. It is automatically activated when a bottle is pressed down onto the unit. Female hose thread connection.
$17.99
-
2 Gallon Food Grade Bucket
A little bucket with a lot of uses. An ideal size bucket fermenter for doing 1 gallon fermentations. Ideal for your next small batch of fruit wine. Used to scoop fermented grapes out of the your fermenter and into the press. Place under a press to collect run off. This list goes on! Wide opening allows for easy cleaning. Lid sold separately. 9-1/4" H x 9-1/2" D (without lid) 9-7/16" H x 9-15/16" D (with lid)
$9.99
-
Beer Bottle Brush
A traditional brush for cleaning 12 to 22oz beer bottles. Many customers like this design for its rounded bristles at the end of the brush that do a great job cleaning the lower half of the bottle. Includes circular metal loop for hanging. Bristles are 2.75" in diameter with an overall length of 16".
$5.00 $4.39
-
The Carboy Cleaner™ - Replacement Pads
A set of replacement pads and washers for The Carboy Cleaner™. Eventually when your original pads have cleaned enough carboys and kegs, they'll need to be retired and replaced by a set of these new ones! Set of 2 replacement pads and 4 washers for The Carboy Cleaner™.
$13.99
-
Lid for 2 Gallon Bucket
Tight fitting lid for our 2 Gallon, food-grade, bucket fermenter, JAR20.
$3.99
-
Heavy Duty Brewing Gloves
Great for cleaning your winery! The gloves are made from a chemical resistant PVC that protects your hands from harsh cleaning chemicals. With a length of 21.5 in, these gloves allow you to reach into liquids while protecting your hands and forearms. Kegland Part Number: KL05289
$13.49
-
Mark II Keg & Carboy Washer
Mark’s Mark II Keg Washer™ is designed to clean and sanitize large vessels like cornelius kegs and carboys. It is also intended to provide a sanitation container for miscellaneous items such as airlocks, thermometers, tubing, keg fittings, and more. Quiet, Fun, & Easy to Use Very quiet when in use and most importantly speeds up the process of cleaning and sanitizing. Light in weight. Easy to store. Cleans Kegs Cleans and sanitizes a cornelius keg without having to take apart the ball lock fittings, poppets, and dip tubes. You can clean the keg and the dip tube simultaneously using the T adapter. Cleans Tubing Too Cleans tube separately utilizing the pump with the additional barb fittings included. Cleans Parts Reservoir holds 1.25 gallons of water making it easy to fill and empty with sanitizer. Saves water and sanitizer. The unit does not have an on/off switch, you can plug it directly into a wall outlet to operate the pump or plug it into an outlet that is controlled by a switch. Never leave the keg washer unattended when in use. When in use, fill the keg washer up to about 1 inch under the brim. The pump is not self priming, so always make sure the basin is full of water before plugging in the pump. Owner's Manual is included. Please read thoroughly before using. Dimensions of the inside of the washer's reservoir are: 6"L x 12"W x 4"D. Please Note: Product does not include the bucket, carboy, or keg pictured above for display purposes. The pump specs are: 520 GPH 120 Volts AC 40 watts Ceramic shaft, impeller
$99.99
-
Line Brush - 1/4 in. x 36 in.
Use for cleaning out the dip tube on your Cornelius keg. Ever wonder how to really clean that ... well now you know. Also, great for 1/4"ID beer line and racking canes.
$6.19
-
Carboy Brush for PET Carboys | Plastic Coated Bristles
This L-shaped brush is the ideal tool for cleaning every inch on the inside of carboys, and thanks to the plastic coating, they won't damage plastic fermenters and PET carboys. Standard carboy brushes like the CE40are great for cleaning glass carboys, but shouldn't be used on plastic. The metal rod where the bristles attach can scratch plastic, which become hiding spots for bacteria. You won't have to worry about that with this carboy brush! Bristles made from Food Grade nylon Long enough to reach deep inside large carboys L-shaped bend allows you to scrub the top portion of carboys that straight brushes can't reach Height from end of handle to 90° bend - 21.5" Brush section with bristles is 8.5" long Bristles are 2.75" in diameter Temperature rated to 140°F (60°C)
$9.99
-
Carboy Brush - Stainless Steel (Rust Proof)
Get to the bottom and sides of that glass carboy. The bent head of the brush makes short work of cleaning the Kraeusen (foam on top of beer) after fermentation. This brush is made with stainless steel so you won't have any rusting issues like with other carboy brushes. 26" from end of handle to 90 degree bend. Bristles are approximately 1-1/4" in length.
$7.99
-
$9.99
-
Carboy Brush with Hook for hanging
Carboy Cleaning Brush – With handle for hanging Keep your fermenters spotless with this durable, Italian-made cleaning brush. The long 23-inch handle reaches deep into glass or plastic carboys, making it easy to remove residue from the bottom and shoulders. A 6" x 2¼" bristle head provides excellent coverage, while the stiff bristles easily scrub away stubborn yeast and trub without scratching surfaces. The lightweight plastic handle includes a built-in hook for convenient storage and drying. Designed by Ferrari in Italy, this brush is a reliable, long-lasting tool for keeping your fermentation vessels crystal clean and ready for the next batch. 23 inches long overall, bent tip is 6 inches long x 2-1/4 inches wide.
$7.69
-
Sink Faucet Adapter - Stainless
Stainless faucet adapter to convert sink thread to garden hose thread so you can attach a bottle washer or wort chiller. Bottle & Carboy Washer sold separately.
$6.59
-
Faucet Brush
If you have a draft system with faucets you need this brush. About 3/4" diameter.
$3.69
-
Bottle Shaped Beer Bottle Cleaning Brush
Using this brush will ensure that each beer bottle is clean from thick dried on debris and ready for use. 17.5" long. Bristle section is 12" long. Kegland Part number: KL12997
$5.49
-
Copper Scrubber Pad - Distillation Column Packing
Copper scrub pads are great for cleaning stainless steel equipment, and can also be used as packing material for pot or reflux stills to enable the release of sulfides. Made from pure lead-free copper. Kegland Part number: KL08907
$2.59
-
Bucket Blaster - Keg and Carboy Washer
Quickly clean kegs and fermenters while you tend to other tasks High flow rate pump provides a powerful blast that coats the inside of the vessel Use it for cleaning or sanitizing with your favorite solutions 15L bucket provides a much larger reservoir compared to other models Everything included in the system neatly fits inside the bucket for easy storage The Bucket Blaster is a convenient and effective system for cleaning and sanitizing kegs, carboys, and other brewing vessels. The beauty of the Bucket Blaster is that you can set it and forget it. Simply set up the keg washer basin with your cleaner or sanitizer, set your vessel over the jet nozzle, power up the pump and let the Bucket Blaster do the work while you tend to other tasks. Perfect for homebrew kegs, carboys, FermZillas, or bucket fermenters. This unit comes with a 15L (3.9 gal) bucket, which doubles as a storage container when you are not using the system. Other keg washers come with a very small reservoir that make it a pain to move, as liquid spills over the sides easily and generally they just do not work as well. The Bucket Blaster's large 15L reservoir makes it much less likely for you to spill liquid on the floor, and since it can hold more cleaning solution, each cleaning cycle will be that much more effective. Includes: Submersible Pump - 2,000 L/hr 15L Bucket Powerful Jet Nozzle 9.5 mm EVABarrier Tubing Gray and Black Ball Lock Disconnects Duotight fittings for all connections Kegland Part Number: KL15905 Bucket Blaster Instruction Manual
$87.99
-
BrewBuilt® CIP Spray Ball | 1.5" T.C.
BrewBuilt CIP Spray Ball for use with X-Series Uni Conicals or any stainless steel fermenter with 1.5" tri-clamp fittings. The head emits a 360° fan spray that cleans above and below the spinning ball. The sharp spray easily removes soil inside your tank. The long neck design allows the spray ball to reach through tall fittings and ferrules. With a welded 90° elbow inlet, you won't have any trouble with kinked hosing slowing your pump flow and lowering the spray ball's performance. A pump capable of 30-45 psi and 11 GPM is recommended for this product to provide a high pressure cleaning radius of 3.6 ft. When used with BrewBuilt conicals, 7 GPM is enough to coat the full interior of the fermenter, but longer CIP runs might be required to fully breakdown stubborn solid deposits.
$99.99
-
ForgeFit® Bucket Strainer for Brewing Hardware
This stainless steel bucket strainer is an excellent accessory to make cleaning and sanitizing your hardware quick and easy. Place the strainer inside a bucket of cleaning solution or sanitizer and then toss in your tri-clamp fittings or other parts. When you're done, simply pull the basket out of your bucket using the handle and all of your hardware will be conveniently contained in the basket. No need to submerge your whole arm into chemical solutions to fish out parts! 9.875" H x 8.25 Ø Please note: the dimensions of the strainer are not the same as the inner dimensions of a standard 6-gallon bucket. The strainer was designed to fit multiple sizes of buckets, so it will not be as wide or tall as larger sized buckets.
$129.99
-
CIP Spray Ball | 4" x 1.5" Tri-Clamp
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory. This stainless steel CIP spray ball kit is perfect for homebrew conical fermenters as many popular units out there feature a 4" T.C. top port or clamp-on lid with 4" T.C. ferrule. Tri-clamp gasket not included. Kit Includes: 4" T.C. Cap with 1.5" T.C. x 1" BSP Male Thread connections 1" BSP x CIP Spray Head Requires pump with 12 GPM flow rate KegLand Part Number: KL22989
$65.99
-
KegLand Rechargeable Power Sprayer | 33 oz
Perfect for spraying down brewing equipment with dissolved cleaners or sanitizers Attach the optional Ball Lock Keg Post Adapter to convert the sprayer into a line cleaning device Empty the large 33.8 oz tank up to 30 times on a single charge The Power Sprayer is a fantastic multi-purpose device that can be used for spraying down your brewing equipment with cleaners and sanitizers or converted into a pressurized line cleaning system. The tank features graduated volume markers and can be emptied up to 30 times on a single charge. The nozzle knob can be adjusted to turn the stream into a fine mist or a powerful jet. This product is made from food grade Santoprene, PP, PE, Silicone and stainless components. Battery Life The pump has large 18650 li-ion rechargeable battery. On a full charge the battery will empty the tank 18-30 times so it lasts for ages. If you use fine mist it will be closer to 18 times but if you use a jet/stream the battery will last closer to 30 times. Includes: 33.8 oz Reservoir Tank Power Sprayer Nozzle and Dip Tube White Plastic Adjustment Head Sprayer 6" USB-C to Standard USB Cable *Does not include USB wall charger KegLand Part Number: KL40860
$27.49
-
KegLand Power Sprayer | Ball lock Keg Post Adapter
Converts the KegLand Power Sprayer into a compact, convenient line cleaning device Ball Lock multi-post is compatible with both Gas & Liquid QDs Attach the Ball lock Keg Post Adapter to the KegLand Power Sprayer to turn the unit into a convenient line cleaning device. The multi-post is compatible with both Gas & Liquid ball lock quick disconnects. This part is only suitable for the Power Sprayer. It is not a standard thread size. It has been custom made for this product and this product only. Please Note: The keg post adapter does not include a spring & poppet. This is intentional in order to prevent the flow path from being blocked if the sprayer was unintentionally powered on without a ball lock disconnect connected to the post. Powering the sprayer with the flow path blocked could damage the pump. KegLand Part Number: KL42871
$10.99
-
EnoItalia Tank Washing Pump | Stainless Centrifugal Pump | 52 GPM | 220V Single Phase
Perfect for wine tanks where a built-in or top-mounted spray ball is not an option Pairs with the optional the stainless steel washing slide inside your tank and connect the tank outlet to the inlet of the pump The pump will deliver 52 gallons per minute at 36 PSI Ideal for tanks with a maximum height of 10 feet This high-pressure centrifugal pump is included with the EnoItalia Tank Washing System. Perfect for wine tanks where a built-in or top-mounted spray ball is not an option. Intended for use with the stainless steel washing slide, but the pump can be used on its own to create a cleaning circuit that better suits your needs. The stainless centrifugal pump delivers 52 gallons per minute with 2.5 BAR of pressure and features 2" T.C. outlet and 1.5" T.C. outlet. Specs: Ideal for tanks with a max height of 10 ft Flow Rate: 52 GPM at 36 psi Inlet: 2" tri-clamp Outlet: 1.5" tri-clamp Power: 220V Single Phase, 2 HP
$1,779.99
-
Speidel CIP System | Clean In Place | Stainless Steel Conical Tanks | Rolling Cart | 110V
Efficient Cleaning: This CIP system is designed for effective cleaning of fermenters and closed systems, equipped with a powerful stainless steel pump that ensures thorough circulation. Precise Temperature Control: Features a temperature display and heating device for caustic, along with a temperature gauge for acid, ensuring optimal conditions for cleaning, acidification, and rinsing processes. Compact and Movable Design: The unit is compact and easily movable with 4 caster wheels, making it flexible and convenient to use in various brewing environments. This Speidel CIP System is designed for efficient and thorough cleaning of fermenters and closed systems like plate chillers. Equipped with a temperature display and heating device for caustic, a temperature gauge for acid, and a powerful stainless steel delivery pump, this system ensures effective cleaning, acidification, and rinsing processes. The unit is compact, movable with caster wheels, and features easy connection options. Acid or caustic is pumped into the fermenter to be cleaned, from there it is circulated via a CIP spray ball and then pumped back into the container after use. In a closed system, e.g. plate chiller, from the storage tank in the circuit directly back into the storage tank. Backflow in each case simple via a hose through the open lid back into the respective storage tank. Process: Pre-rinse: Remove dirt Cleaning: Caustics are run through the system parts Rinsing 1: The cleaning medium is flushed out with water Acidification: Deposits and scale are removed with the help of acid solutions *Only necessary at certain intervals, not after each fermentation or brewing process Rinsing 2: The acid is flushed out with water Product Details: 7.9G (30L) conical tank with temperature display for caustic with heating device 7.9G (30L) conical tank with temperature gauge for acid Connections DIN NW 25 for hose 1" plus connection option water Gardena Delivery pump made of stainless steel 880W / 4.5bar / 1,188 gal/h / 4,500 L/h Heater in the suds tank - adjustable temperature E-junction box with on/off for pump and heating Connection voltage: 110V Connection cable 9.8' / 3m Movable with 4 caster wheels Compact and flexible in use Dimensions: Height: 43.3" (110cm) Width: 22.4" (57cm) Length: 47.2" (120cm) Weight: 132 lbs (60kg) Please Note: This item may come with a bare cord or with a European style plug. You will need a professional electrician to wire the unit with the appropriate plug. Please Note: This unit is not specifically designed for certain mains voltage. It is compatible with both 110V and 230V and 50 or 60 Hz. However, the plaque on the unit may display 230V.
$6,709.99
-
EnoItalia Washing Slide | Stainless Steel Spray Wand | 1.5" Tri-Clamp
Designed for use with the EnoItalia Tank Washing System. This stainless steel washing slide is a great option for tanks with manway doors that do not have a built-in spray ball for CIP. Place the washing slide inside your tank and snake the tubing through the maway door. Connect the washing slide to your pump's outflow and the bottom drain of the tank to the pump's inflow to create a cleaning circuit. Recommended for use with the EnoItalia High-Pressure Centrifugal Pump. 1.5" T.C. inlet connection.
$629.99
-
EnoItalia Tank Washing System | Stainless Centrifugal Pump & Washing Slide | 52 GPM | 220V Single Phase
Perfect for wine tanks where a built-in or top-mounted spray ball is not an option Place the stainless steel washing slide inside your tank and connect the tank outlet to the inlet of the pump The pump will deliver 52 gallons per minute at 36 PSI Ideal for tanks with a maximum height of 10 feet A simple, yet effective, high pressure washing system for wine tanks where a built-in or top-mounted spray ball is not an option. The washing system includes a high-pressure pump and a stainless steel washing slide. The washing slide is connected to the outflow of the pump and placed in the middle of the tank with the hose snaking through the manway door. Then the bottom outlet of the tank is connected to inflow of the pump to create a cleaning circuit. The stainless centrifugal pump delivers 52 gallons per minute with 2.5 BAR of pressure and features 2" T.C. outlet and 1.5" T.C. outlet. Includes stainless steel washing slide with 1.5" T.C. connection. Specs: Ideal for tanks with a max height of 10 ft Flow Rate: 52 GPM at 36 psi Inlet: 2" tri-clamp Outlet: 1.5" tri-clamp Power: 220V Single Phase, 2 HP
$1,629.99
-
Filling & Cleaning Lid for FD-Style Speidel Fermenters
Clean in place with this filling and cleaning lid for FD-Style Speidel Fermenters. Just attach CIP Spray Ball (included) and pump hot water through to clean your fermenters. Use to maximize aeration when transferring wort into your tank. Generally speaking this lid is pretty sweet! 1" MPT inlet w/ 1" Pipe
$904.99
