Stainless Steel Tri-Clamp Fittings & Valves

This is a Stainless Steel one way Check Valve. It has 2" T.C. Fittings on either side, and releases pressure at ~1 p.s.i. Can be used to inhibit a siphon in certain applications, or to vent gas pressure in a tank.

Read more less

Adapt any 3" tri-clamp port or valve to work with an existing 1.5" tri-clamp fitting. The concentric design limits flow resistance as you step down from 3" T.C to 1.5" T.C.  Perfect for pairing with the BrewBuilt X3 Conical's 3" bottom port and attaching 1.5" tri-clamp fittings. 1.5" x 3" tri-clamp 7" tall Made from 304 stainless steel

Read more less

Replacement Polycarbonate Cup if you happened to damage or lose the reservoir for the 1.5" Tri-Clover Spunding Valve during routine cleaning and replacement of sanitizer solution post-fermentation. KegLand Part Number: KL27472

Read more less

The BrewBuilt T.C. spunding valve will give you the highest level of accuracy when fermenting under pressure. Designed for use with the BrewBuilt X-Series Uni Conical Fermenter, the spunding valve attaches to the lid's 1.5" tri-clamp port where the blow off fitting is normally installed. It can also be used with any pressurizable stainless steel conical with 1.5" T.C. top ports. The polycarbonate cylinder that surrounds the spunding valve can be filled with water or sanitizer to keep your tank 100% sanitary throughout the fermentation process. Adjustable from 0.3–14.5 psi Made from 304 stainless steel 11.75" H x 4" Ø   For Your Safety: Never exceed the maximum rated working pressure of your vessel at any time during operation. The fixed-pressure PRV on your conical should always remain in place while using this spunding valve.

Read more less

The BrewBuilt Whirlpool Return Fitting allows you to recirculate wort in your boil kettle without sacrificing one of your tri-clamp ports. Install it in any tri-clamp kettle's thermometer port and attach your preferred valve to the side inlet. The front of the fitting can be capped off with a 1.5" T.C. end cap, or you can pair with the BrewBuilt Thermowell Offset to install a thermometer or temperature probe.  

Read more less

End cap for 2.5" tri-clamp fittings. Made from 304 stainless steel.

Read more less

Camlock to tri-clamp adapter. Perfect if you prefer camlock fittings on your tubing lines and own a brewing kettle, pump, or fermenter with tri-clamp fittings. Male camlock fitting x 1.5" tri-clamp. Made from 304 stainless steel. KegLand Part Number: KL20237

Read more less

304-type stainless steel tri-clamp extension tube with 1.5" clamp ends. 12" long.  

Read more less

The Blowoff U Barb eliminates tubing kinks by extending over the shoulder of a stainless conical fermenter and directing tubing straight downward. This gives you the advantage of a stainless steel blowoff cane, but is much easier to clean and sanitize. The 5/8" OD barb is perfect for forming a tight seal with 1/2" ID silicone tubing. Measures approximately 4" from T.C. to barb. 1.5" T.C. 5/8" OD barb Made from 304 stainless steel  

Read more less

Replacement valve seat for plunger-style 1.5" tri-clamp sample valve. Compatible with FF120.  

Read more less

Replacement interior gasket for the H661B 2" Butterfly Valve

Read more less

2.5" TC Ferrule is used to weld in a TC connection anywhere you need one!  AiSI304 Stainless Steel.

Read more less

Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections Silicone gaskets have a wide temperature range and are recommended for hot side applications For 3" tri-clamp connections A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both Silicone and EPDM. Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 3" tri-clamp fittings Made from Silicone Temperature rated from -58°F to 446°F KegLand Part Number: KL44813

Read more less

This ForgeFit barb hose end is intended for use with 1" professional beverage tubing. This is the same fitting we use on our pre-fabricated beverage hose assemblies. When designing this fitting, we made sure it has all the features we wanted in a barb intended for professional applications. The hose barb has a shoulder to keep the hose from creeping up towards the fitting end. The long barb promotes solid engagement with the hose and the end has a gentle internal taper to transition the product flow smoothly from the fitting to the tubing. 1.5" tri-clamp connection with 1" OD 2.62" long barb. Overall length 3.25". 3A certified 304 stainless.

Read more less

Teflon gasket with 304 stainless mesh screen for 2" tri-clamp connections. Can be used as a filter screen to trap large particulates passing through T.C. fittings. Often used for distillation to retain activated carbon for filtering neutral spirits or used in pot distillation to retain botanicals in the vapor stream. The screen has a mesh size of 16 which will block particles larger than 1.19mm or 1190 microns. This mesh size makes this screen ideal for use in a filer setup with activated carbon. Kegland Part Number: KL30496

Read more less

This stainless steel tri-clamp features two hinges and folds into three pieces. Some brewers find this style of clamp easier to work with on large equipment that requires a 3" clamp. Direct replacement part to the clamp included with the FermZilla Tri-Conical fermenter. KegLand Part Number: KL25799

Read more less

Tri Clamp adapter that goes from a 3" TC to a 1.5" TC.

Read more less

Stainless steel Tri-Clamp reducer with 3" T.C. and 1.5" T.C. connections.

Read more less

3" TC Ferrule is used to weld in a TC connection anywhere you need one!  AiSI304 Stainless Steel.

Read more less

Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections Silicone gaskets have a wide temperature range and are recommended for hot side applications For 8" tri-clamp connections A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both Silicone and EPDM. Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 8" tri-clamp fittings Made from Silicone Temperature rated from -58°F to 446°F KegLand Part Number: KL44790

Read more less

Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections Silicone gaskets have a wide temperature range and are recommended for hot side applications For 4" tri-clamp connections A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both Silicone and EPDM. Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 4" tri-clamp fittings Made from Silicone Temperature rated from -58°F to 446°F KegLand Part Number: KL44806

Read more less

Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections Silicone gaskets have a wide temperature range and are recommended for hot side applications For 1.5" tri-clamp connections Flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both Silicone and EPDM. Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 1.5" tri-clamp fittings Made from Silicone Temperature rated from -58°F to 446°F KegLand Part Number: KL44837

Read more less

Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections EPDM gaskets are more resistant to acids and caustic chemicals, and don't show signs of wear as quickly as silicone For 8" tri-clamp connections A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both EPDM and Silicone. EPDM gaskets have a more narrow temperature range than silicone gaskets, but they are more resistant to acids and caustic chemicals. For 8" tri-clamp fittings Made from EPDM Temperature rated from -30°F to 300°F KegLand Part Number: KL45193   Example Image: Updated images coming soon. See the video below to check out the flanged gaskets in action.

Read more less

Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections EPDM gaskets are more resistant to acids and caustic chemicals, and don't show signs of wear as quickly as silicone For 4" tri-clamp connections A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both EPDM and Silicone. EPDM gaskets have a more narrow temperature range than silicone gaskets, but they are more resistant to acids and caustic chemicals. For 4" tri-clamp fittings Made from EPDM Temperature rated from -30°F to 300°F KegLand Part Number: KL45209   Example Image: Updated images coming soon. See the video below to check out the flanged gaskets in action.

Read more less