Wine Making Hardware

The BrewBuilt tri-clamp thermometer features a large 3" face for easy reads and 2" probe is less obtrusive in your conical fermenter or T.C. kettle. Dial face reads from 0-220°F and -10-100°C. 3" dial face 2" probe 1.5" T.C. Reads in °F and °C  

Read more less

Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 2" tri-clamp fittings. KegLand Part Number: KL03438  

Read more less

3/4" female garden hose thread x 3/4" female garden hose thread. Maximum temperature rating - 195°F.

Read more less

Stainless steel 3-piece ball valve with tri-clamp connection and 1/2" female NPT out. A great option for T.C. kettles, pumps, and conicals to go from 1.5" tri-clamp to any 1/2" male threaded connection or accessory. Full port for higher flow rate. A seat in the back of the valve allows for the installation of a pick up tube or racking arm.  

Read more less

3/8" female x 1/2" male BSP reducing bush. Made from 304 stainless steel. Kegland Part Number: KL06576  

Read more less

This Stainless Steel BSPP barb will connect any tubing with a 3/8" ID line to any fitting with a 3/8" Female BSPP connection. The barb is slightly oversized at 10 mm (0.39") compared to 3/8" (0.37") which will give you a tighter connection with your tubing. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" and 3/4" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL06644  

Read more less

1/2" NPT flat nut

Read more less

Female 1/2" NPT coupler

Read more less

This fitting has 3/4" Male Garden Hose Thread on one side and both 3/4" MPT and 1/2" FPT on the other.

Read more less

Brass - 1/4'' FPT x 5/16'' barb

Read more less

Serve beverages at different pressures without the need for multiple CO2 cylinders, dual body regulators, or expensive gas manifolds Feed a single pressure to the gas board from your regulator and then step down the pressure on each Duotight regulator Use one line for serving ales, another for soda or seltzer water, and another for carbonating a freshly filled keg All parts shown are included and snap together quickly thanks to Duotight push-to-connect fittings and rigid plastic joiners Duotight In-Line Regulators feature built-in pressure gauges that read 0-60 PSI and can be swapped out for different ranges if desired The Duotight Draft Regulator Board is a simple and cost-effective solution to serving beer and other beverages on draft at different pressures. With a standard CO2 tank and CO2 regulator, you can feed gas at a single pressure into the regulator board and then fine tune individual pressure settings for each gas line via the Duotight In-Line Regulators. These regulators feature built-in pressure gauges that make adjustments super simple and check valves are included as standard so you never have to worry about back flow into the regulator. This kit includes everything you need to assemble your regulator board and can be customized so the gas inlet is on the right or left side—whichever makes the most sense for your home draft setup. Duotight push-to-connect fittings and the precut rigid joiners make assembly a breeze and only takes 10-15 minutes! The draft board kit comes in two options—with or without shut off valves. These valves offer peace of mind and allow you to shut off gas flow to any line that is not in use. If you ensure that your system has no leaks, they aren't technically needed, and you can always fully tighten your Duotight Regulator adjustment knob for added protection. But that little extra security might help you sleep easier at night! One advantage of choosing no check valves, however, is that it will leave room at the top of the board to label your gas lines. One of the coolest features of the Duotight In-Line Regulator is that the included pressure gauge can be swapped out for different pressure ranges. The standard gauge reads 0-60 PSI, but if you have one line that will always be used for serving Ales, you can swap to a 0-15 PSI gauge that will be a little easier to read and make precise adjustments. There's also a Digital Pressure Gauge available that provides backlit instant reads and is rated from 0-90 PSI. Need more than 4 gas lines? Check out the 6-Way Duotight Draft Regulator Board. Please Note: Full assembly required. The gas board, regulators, and fittings will arrive loose. Please see our instructions and assembly video below. Stepping Down Pressure The ideal regulation scenario occurs when the inline regulator steps down the output pressure to at least 10 PSI less than the inlet pressure. For example, if the inlet pressure is 30 PSI, the regulator effectively manages a range from 0–20 PSI on the output side ensuring optimal performance and stability. Ideal regulation scenario (10 PSI less than inlet pressure) Example of 30 PSI inlet translating to 0–20 PSI output Kit Includes: 4-Output Gas Board (4) Duotight In-Line Regulators (4) Duotight Check Valves (4) Duotight Shut Off Valves (if selected above) (3) Duotight Tees (1) Duotight Elbow (15) Rigid Plastic Joiners NOTE: All Duotight fittings and rigid plastic joiners come as 8mm OD. Mounting hardware is included for the regulators but not for mounting the board itself to a wall or the inside of your kegerator/keezer. If you select the option without shutoff valves, you will be left with some spare joiners after assembly.

Read more less

This disconnect has an internal check valve that will allow the gas to flow out, but won’t allow backflow of liquid back into your system. Internal Check Valve protects your system from liquid back flow! Made in Germany and assembled in the USA by CMB. Extremly high quality for years of service. NSF Approved for Food Grade Service!

Read more less

These stainless stepless clamps tighten in an exact circle, making them ideal for use with draft lines. Suitable for 7/16" OD tubing (10.5-12.5 mm OD). Comes in packs of 20 clamps. Stepless Clamp Tool sold separately - H1006 Kegland Part Number: KL06699  

Read more less

This is a Stainless Steel one way Check Valve. It has 2" T.C. Fittings on either side, and releases pressure at ~1 p.s.i. Can be used to inhibit a siphon in certain applications, or to vent gas pressure in a tank.

Read more less

304-type stainless steel tri-clamp extension tube with 1.5" clamp ends. 18" long.  

Read more less

These long shanks are suitable to attach to large commercial fermenters and brite tanks with a 1.5" Tri-Clamp Port. Being removable and completely washable it makes this device extremely easy to clean and sanitize before use. Ideally used with the NukaTap Flow Control Faucet with Self-Closing Spring. Please note standard NukaTap SS Faucet and Self-Closing Spring will not work with this shank. You can use a NukaTap SS faucet, but without the autoclose spring. Also compatible with Intertap, Perlick, and other faucets. Specifications: 2.75" total length Standard shank assembly 1.5" T.C. connection KegLand Part Number: KL19989

Read more less

Anvil Brewing Equipment ball valve is made from 304 stainless steel. This robust custom designed kettle drain valve has an integral bulkhead seal that forms an extremely rigid and leak-free joint. The convenient ½” NPT male fitting inside of the kettle allows mounting of nearly any accessory.  Simple to install in any 7/8” hole and will never leak like other weldless connections! Easy to disassemble and clean. Add our dip tube for a complete draining system! When installed, the valve O-Ring will sit in the groove on the back of the valve, on the outside of the kettle.

Read more less

1/4" male BSPP stainless steel plug. Hex head design for easy installation or removal with a wrench. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" and 3/4" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL06392  

Read more less

This replacement spring is intended for use with our adjustable stainless steeel pressure relief valve - D1832L & D1833L. These units are adjustable from 0 to 30 psi. Example photo shown. The spring you receive may not match the photo exactly.  

Read more less

Includes Pin lock beverage out quick disconnect, line, hand held faucet and two hose clamps. 5 ft of 3/16" line.

Read more less

Includes ball lock gas-in quick disconnect (barb), 5 ft of 1/4" ID tubing, and two hose clamps.

Read more less

This is a ball-lock type quick disconnect that is constructed from stainless steel for lifetime longevity. 1/4" barb. This QD is for the Bev Out side. See here for the Gas In QD. 2 1/8" H Please note: the outer bushing on the disconnect is made from chrome-plated brass. All parts that come into contact with liquid are stainless. Kegland Part Number: KL02998

Read more less

Oversized corny keg, great for bigger batches and fermentation Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Brand new, all-stainless construction ball lock keg Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Set your sights on a brand new Torpedo Keg! The patented, D794,899, sleek all-stainless design represents the pinnacle of quality in ball lock homebrew kegs. With features like welded stainless handles, the ability to stack with fittings in place, amazing quality and a great price we think these kegs will become the standard by which other kegs are measured.    Quality First The first thing we at MoreBeer! check out is interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. These kegs are machine welded and exceed our standards for quality. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. In and Out is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake.  Stainless Fermenter We've seen a lot our customers having great success using the 6-gallon Torpedo Keg as a stainless steel fermenter or "kegmenter". The extra headroom that this size offers makes it a great option for fermenting 5-gallon batches. We highly recommend using CellarScience Foam Axe if you're fermenting in the keg. Foam Axe will help reduce krausen buildup, cutting down the chance of clogging issues with the ball lock poppets and the PRV in the keg lid. It should also be noted that leaving your finished beer on the leftover trub from fermentation for too long will eventually lead to off-flavors. If it won't be consumed in 2-3 weeks, transfer your beer to a fresh keg using the Torpedo Keg Buoy which will pick up the clearest beer and leave the sediment behind. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions: 27.15" H x 9" D

Read more less