Products

Drill a 1'' hole and install in bucket. Spigot uses 3/8 in ID tubing. Place the gasket on the outside of the bucket. Also fits ported Fermonsters and attaches the same way.

Read more less

This is the installation tool to install spigots in the Vintage Shop ported PET carboys. The wrench has a specially molded hex nut to hold the 5/16 inch barbed (FE347) or 1/2 inch barbed (FE347A) spigot nut, and a long handle so you can reach to the bottom of the carboy. The spigot wrench can be reused, you only need it during the installation and/or removal of the spigots.

Read more less

Replacement female threaded brass piece which mounts into the fixed stainless plate (non-pump side) on an OMAC 20x20 plate and frame filter. This is the part of the filter that the spindle threads through in order to push the floating plate inward and close the filter once the pads have been installed. They occasionally strip out due to the force applied when sealing the filter for operation.

Read more less

By itself the Vortex funnel allows for fast transfers of wine or sanitizing solution.  Use the optional filter paper for removing tartrate deposits, oak, spices, fruit, etc. out of your wine, fruit wine, or liquors.

Read more less

Splash Guard for Cannular Pro Semi-Auto Bench Top Can Seamer (CAN110). For the splash guard for the manual Cannular Can Seamer, see CAN105.   Kegland Part number: KL16728

Read more less

Please Note: This part is intended to be used with the Manual Cannular Seamer (CAN100) which has been superseded by the Cannular Pro. This item will not work with the Cannular Pro (CAN110). Splash Guard for Manual Cannular Bench Top Can Seamer (CAN100). For the splash guard for the Cannular Pro Semi-Auto Can Seamer, see CAN106.   Kegland Part number: KL16711

Read more less

A food grade, high temp plastic spoon perfect for stirring the mash or wort during brewing. Works best with 4 to 10 gallon size kettles. Tip: Turn the spoon upside down and use the skinny end to stir inside a carboy. Plastic spoons are preferred when using plastic fermenters or bottling buckets as they are less likely to scratch.

Read more less

A food grade, 28" high temp plastic spoon perfect for stirring the mash or wort during brewing. Works best with 4 to 10 gallon size kettles. Tip: Turn the spoon upside down and use the skinny end to stir inside a carboy. Plastic spoons are preferred when using plastic fermenters or bottling buckets as they are less likely to scratch.

Read more less

Unlike standard low-end bottle fillers, the Vintage Shop's springless model uses a plastic valve instead of a spring to seal. The springs are not made from a food grade quality metal. Fillers will work with 12 or 22oz bottles. Use with 1/2" tubing. Larger 1/2" diameter and increased flow is good for wine applications.

Read more less

Unlike standard low-end bottle fillers, the Vintage Shop's springless model uses a plastic valve instead of a spring to seal. The springs are not made from a food grade quality metal. Fillers will work with 12 or 22oz bottles. Use with 3/8" tubing.

Read more less

These square cloths are perfect for Kombucha brewing. Let your fermenting SCOBY breathe while keeping bugs and airborne contaminants out. Perfect for large open top fermenters, such as Bucha Tanks.  

Read more less

These square cloths are perfect for Kombucha brewing. Let your fermenting SCOBY breathe while keeping bugs and airborne contaminants out. Perfect for 1 gallon jar fermenters  

Read more less

Square plastic plug for bottom rails of the Italian manual (WE220, WE220PS) and motorized (WE223PS) crusher destemmers.   In documents tab: Position: 7 Quantity Used: 4 EnoItalia Item #: G20

Read more less

500 mL flint (clear) square sided bottles. Standard cork finish. Often used for specialty beverage, olive oil, sauces, and more. Sold in cases of 24. Bottle Specifications: Capacity: 500 mL Weight: 0.88 lb Height: 10.51 inches Outside 2.3" x 2.3" Shipping Details: Case: 24 Bottles Full Pallet: 96 Cases  

Read more less

TWO - 240VAC 30AMP GFCI Dedicated Circuits Required Designing every piece of our electric brewing equipment from scratch has enabled us to introduce a new level of process control, flexibility, and performance.  Every detail has been carefully thought through and refined. Every component of our new eControllers were designed in house or selected to enhance the ebrewing experience.  Beginning with the custom extruded 6061 aircraft-grade aluminum housing, which is CNC machined, and then coated in a durable black anodized finish. Using this approach allowed us to keep the system compact, portable, and functional.  The housing includes an integrated carry handle for easy setup and take down, a tee-slot for alternative mounting options, along with a heatsink to keep the internal electrical components cool. The boilkettle output on the eController is driven by a fully proportional PID controller, which doesn't rely on high speed switching to modulate heat.  Instead, voltage is modulated through an internal SSVR, this means element wattage is proportional.  A switch located just above the PID allows the user to operate the controller in manual or automatic modes. In manual mode, the proportional output can be fine-tuned on a scale of 0-100% of total element output which is ideal for dialing in a perfect rolling boil.  Alternatively, in automatic mode, the PID algorithm manages the proportional output relative to process temperature, to hold a steady HLT or mash temp for instance.  The eController quickly finds equilibrium with environmental heat loss characteristics, and can maintain a high degree of accuracy during each brewing process. The heater button allows the user to cycle the element on or off without shutting down the power to the entire unit, or adjusting the PID output setting, which is especially helpful during the occasional boil-over. This feature also allows the controller to be used to monitor a process temperature, such as during runoff or latter stages of the sparge process without the risk of dry firing the element.  Lastly, the controller features two accessory outputs, which would commonly be used for pumps, but could also be used for a mill, lighting, or even a phone charger. Connectivity was an important consideration for our eControllers, we wanted the flexibility and familiarity of a plug that could be adapted to an existing customer supplied kettle or element, and the reliability of a UL approved connector type.  For 240VAC main power and element connectors, we settled on the common NEMA L6-30 standard, which is a 3-wire twist-lock plug type, capable of delivering 30 amps of current.   For the accessory connections, we settled on using a NEMA 5-15 standard, which is just a standard residential 120 VAC outlet.   Finally, for the PT100 temperature probes we opted for the 3.5 mm mini jack connector standard, commonly used for headphones, which is both durable and easy to use. Extruded Anodized 6061 Aluminum Housing Omron Proportional PID Controller Automatic and Manual Modes On/Off Element control PT100 temperature probe (2) 120 VAC Accessory receptacles TWO - 240VAC L6-30 Plugs (2) discreet 30A GFCI circuits required TWO - 240VAC 30AMP GFCI Dedicated Circuit Required Designed to be used with Ss Brewtech eKettles and RIMS. Use with other heating elements, especially (but not limited to) those of different wattages, can cause damage to the eController not covered under the warranty policy.

Read more less

Features: 304 Stainless Steel Compatible with 1/4" probes Does not include TC gasket 2.75" Thermowell

Read more less

Ss Brewtech 1.5 in. TC Sample Valve Features: All 304 Stainless Construction Knob/Bonnet operation Completely sanitary with silicone seal Easy disassembly for cleaning Compatible with most sampling coils

Read more less

The Chiller Coil & Neoprene Jacket kit can be used to update the Standard Ss Brite Tanks for temperature control. Then you can add an FTSs Touch kit for use with the Ss Glycol Chiller. Thick 5 mm zippered neoprene jacket Immersion chiller coil mounted to 8" TC cap 3/8" hose barbs on the chiller coil Included hose clamps (for chiller coil) Not for BME Brite Tanks Not compatible with Brew Bucket, Chronical, or Unitanks.

Read more less

Updating the iconic series of Chronical fermenters is not something Ss took lightly. The Chronical was a product launched in the earliest days of Ss Brewtech. It, along with the Brewmaster Edition that would join a few years later, has formed a core product line that has elevated the standard of what homebrewers have come to expect from a cylindro-conical vessel, and what homebrewed beer could be. So, with a blank sheet of paper, they went to work designing the ultimate Chronical fermenter. Priority number one was to continue on Ss's mission to elevate every home product they offered to sanitary connections and valves. For the Chronical 2.0 they addressed that by adding a new welded 3/4" TC sampling port, and paired that with an all-new sampling valve based on the Pure Flow sanitary technology. Secondly, Ss redesigned the lid to use the Unitank's lid-mounted cooling coil system, which removes the side-mounted weldless ports from the Chronical BME. The Chronical 2.0's lid-mounted cooling coils extend further down into the fermenter, enabling users to ferment partial batch sizes. Although Chronical 2.0 is a massive evolutionary leap forward, Ss also stayed true to the product line's core. The full-width lid, a revolution when the original Chronical launched is retained, the pro-inspired 60° cone, and bottom dump port is still here. And last but not least, the ever-popular neoprene jacket from the Chronical Brewmaster Edition is standard on Chronical 2.0.  This means that every Chronical 2.0 has a coil and jacket included as standard.

Read more less

This kit is designed for owners of Standard Chronical Fermenters and includes everything you need to perform a pressurized transfer.  Simply attach the pressurized transfer fitting to your Chronical's lid with the included TC clamp and gasket.  Then attach the pressurized transfer fitting to your CO2 regulator. Lastly, install the 1/2" barb to the Chronical's racking valve, and run the included 1/2" tubing to a clean and sanitized keg. The pressurized transfer fitting includes a PRV that prevents pressure from building to unsafe levels within your Chronical. This Kit Includes: 1x Pressurized Transfer Fitting 1x TC Clamp 1x TC Gasket 1x 1/2 in. Barb to 1/2 in. NPT 5 ft. 1/2 in. Silicone Tubing 2x Hose Clamps

Read more less

Shelf add on for Ss Brewtech Chronicals. NOT FOR LEGACY 7 GAL CHRONICAL - There are no threaded inserts in the leg bottoms for this to mount to on the 7 gal Legacy Chronical. Features: Made from 304 stainless steel Great place to put your blow off vessel Adds stability when using leg extensions

Read more less

Domed false bottom from Ss Brewtech. Features: Made from 304 stainless steel Domed shape Central suction point Welded handle Silicone gasket Note: These false bottoms are designed for the Ss Brewtech Brew Kettles and will not fit other kettles. They are also not compatible with the Ss Brewtech BME Kettles.

Read more less