Beer Making

Replacement malt pipe handle for the 65L BrewZilla. 3/8" thick. KegLand Part Number: KL29513

Read more less

Replacement probe for the RAPT Bluetooth Thermometer (MT409). The cord is 39" long with a 7.8" long probe probe with sharp tip. Please remove the black plastic tip before use. That is for storage to avoid punctures / injury. KegLand Part Number: KL29445  

Read more less

This stainless steel shuttle can be used to replace the TPV rubber NukaShuttle that comes standard in the NukaTap beer faucet. For users that prefer stainless internal mechanisms in their faucet. You will need to remove the bonnet piece at the handle, pull the handle out and then slide the shuttle piece out. KegLand Part Number: KL35958

Read more less

You can use pass through shanks for beer entry through the back side of a cooler. Drill a 1" hole through the cooler, insert the shank, and use the two attached nuts to tighten up on the cooler. You will need nuts and nipples of the size line you are working with as well as hose clamps. We do not use pass through shanks in our boxes because we drill a hole that is same size as the line so we can pull it back in when we are traveling. However there might be instances where they would be appropriate. Pass through shanks can also be used to put through the side of a refrigerator to pass a gas line through Installation Note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. This is a stainless steel shank with chrome plated brass hex nuts. Dimensions: 4" - Shank Length 4" - Thread Length 2-3/4" - Pass Through Length Max length with hex nuts at either end Does not account for nuts/nipples you may install Male Beer Thread (5/8" BSP)  

Read more less

You can use pass through shanks for beer entry through the back side of a cooler. Drill a 1" hole through the cooler, insert the shank, and use the two attached nuts to tighten up on the cooler. You will need nuts and nipples of the size line you are working with as well as hose clamps. We do not use pass through shanks in our boxes because we drill a hole that is same size as the line so we can pull it back in when we are traveling. However there might be instances where they would be appropriate. Pass through shanks can also be used to put through the side of a refrigerator to pass a gas line through. Installation Note: On a fridge there are generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. This is a stainless steel shank with chrome plated brass hex nuts. Dimensions: 3" - Shank Length  3" - Thread Length 1-7/8" - Pass Through Length Max length with hex nuts at either end Does not account for nuts/nipples you may install Male Beer Thread (5/8" BSP)

Read more less

The BrewKeg25 is a 6.6-gallon (25 L) capacity stainless steel, conical pressure fermenter with sediment removal and an easy to use lid with pressure relief valve. Suitable for batch sizes of up to 6.6 gallons, the BrewKeg25 is suitable for all-grain and extract brewers who want to experience the magic results of pressure fermentation. Ferment under pressure and serve 6.6 gallons of beer from the same vessel without ever transferring! The BrewKeg from WilliamsWarn is a unitank that allows you to ferment, carbonate and serve all in one vessel, saving you money on other equipment. The BrewKeg lets you ferment up to 6.6 gallons of wort at up to 25 psi. The tank itself has a total volume of 7.9 gal, giving it the perfect amount of headspace to produce 6 gallons of finished beer. Fermenting under pressure reduces esters allowing your beer to ferment at higher and more varied temperatures. Fermenting under pressure also produces clearer beer! The fermenter also includes a yeast collection ball so you can remove yeast and trub without having to rack to a separate vessel. The BrewKegs all stainless steel construction and conical bottom make it perfect for extract, partial extract, and all-grain brewers. Features: Made from stainless steel Conical base Extra-large, easy to remove draining sediment ball 25 psi working pressure & built in relief valve 40 psi maximum pressure rating Ferments clean and clear beer from 64-82°F Beer is carbonated perfectly at the end of fermentation Beer ready to enjoy sooner Compact design fits in most kegerators Eliminates kegging Easy to clean and sanitize Dimensions: Height: 26 in. Diameter: 15.5 in. Actual Volume: 30L (7.92 gal)

Read more less

RAPT Controller extension cable for the BrewZilla 35L, 65L and 100L Generation 4 models. Mount your screen up higher in your brew space and get a clear view on brew day. Compatible with 110V / 220V models 4.9 ft. Cable Length (1.5 m) Suitable only for Gen 4 BrewZillas KegLand Part Number: KL32681

Read more less

Controller mounting bracket for the Gen 4 BrewZillas. Mount your controller up to 5 ft. away with the RAPT Screen Extension Cable (AG547). KegLand Part Number: KL32698

Read more less

Kit with 3 legs and necessary accessories to raise the MiniUni base and make room for an elbow with a butterfly valve or a heating element etc. Made from reinforced nylon. With the legs mounted, the height will increase with 5.5". As the legs extends with the same angle as the base, space equivalent of a circle of 14.5" in diameter is needed where placed. In the box: 3 pcs legs 6 pcs silicone plugs 3 pcs M6 bolts Tool for assembly (Hex 5mm)

Read more less

88% concentration. Use to adjust pH of sparge water down.

Read more less

Non-silicone, antifoam agent best used in blow-off buckets. Use as a rate of 1 oz per BBL. This will provide foam surpression for up to 14 days Use at a rate no greater than 1 oz per 5 BBL With blow-off buckets, add as needed. Generally 1 oz. per 30 gallons of foam   Are you a Pro Brewer or a brewery in planing? For the best price on commercial brewery supplies, sign up for an account at morebeerpro.com!

Read more less

Stainless steel splicer fitting for joining different sizes of tubing. Recommended for splicing 3/16" or 1/4" ID tubing to 3/8" ID tubing. One end is slightly undersized at 6 mm (0.24") and the other is slightly oversized at 10 mm (0.39"). Made from 304 stainless steel.

Read more less

Replacement Transformer for BrewBuilt® IceMaster Max 2 glycol chiller.

Read more less

The Stout Spout installs on the NukaTap Mini to improve the pour of your stouts and nitro brews The creamer/aerator disc inside strips out nitrogen gas for a creamier beer Simply unthread the standard spout from the NukaTap Mini and swap in the Stout Spout Simply unscrew the normal spout from the NukaTap Mini and screw this Stout Spout in its place to pour your nitro brews. This spout has a creamer/aerator disc inside that strips out the nitrogen gas for a creamier beer. Only compatible with the NukaTap Mini faucet. The Stout Spout will have a 1/4" female flare thread. KegLand Part Number: KL32858

Read more less

The fitting is to be used in a KegLand Stainless Steel Quick Swivel Connectors in 1/2" Female NPT. This is the end cap only. Handy for terminating 1/2" Quick Swivel Connections. KegLand Part Number: KL31646

Read more less

Replacement O-rings for the 1/2" KegLand Quick Swivel Connectors. Made from high temp silicone. Comes in a pack of 10. These come in brown silicone only. Refrain from using undiluted acidic / heavy strength alkaline substances or the Silicone may change in color. KegLand Part Number: KL31592

Read more less

Replacement 1/2" KegLand Quick Swivel Connector Nut. Comes with a heavy duty silicone grip guard allowing comfortable and quick tool-free operation. Silicone O-ring included. KegLand Part Number: KL31547

Read more less

This straight barb in 1/4" (6.35mm) OD is only compatible with the 1/2" KegLand Quick Swivel Connector Nut. Compatible with 6.35 mm Duotight fittings. Quick Swivel Nut sold separately. KegLand Part Number: KL31554

Read more less

This straight barb in 5/16" (8mm) OD is only compatible with the 1/2" KegLand Quick Swivel Connector Nut. Compatible with 8 mm Duotight fittings. Quick Swivel Nut sold separately. KegLand Part Number: KL31561

Read more less

This straight barb in 3/8" (9.5mm) OD is only compatible with the 1/2" KegLand Quick Swivel Connector Nut. Compatible with 9.5 mm Duotight fittings. Quick Swivel Nut sold separately. KegLand Part Number: KL31578

Read more less

This straight barb in 1/2" (13mm) OD is only compatible with the 1/2" KegLand Quick Connector Swivel Nut. 3/8" (10mm) ID bore. Quick Swivel Nut sold separately. KegLand Part Number: KL31585

Read more less

High temp silicone grip provides a cool touch even with hot liquids! Ribbed grips allow quick comfortable tool-free operation Fits all male 1/2" NPT and BSP fittings 6.35 mm Duotight compatible stainless steel elbow barb tail The KegLand Stainless Steel Quick Connectors come with a heavy-duty silicone grip guard allowing comfortable and quick tool-free operation. Specs: Stainless steel and silicone construction Silicone O-ring seal is retained for perfect positioning but is easily cleaned or replaced 1/4" (6.35mm) OD elbow barb tail KegLand Part Number: KL31677

Read more less

High temp silicone grip provides a cool touch even with hot liquids! Ribbed grips allow quick comfortable tool-free operation Fits all male 1/2" NPT and BSP fittings 6.35 mm Duotight compatible stainless steel barb tail The KegLand Stainless Steel Quick Connectors come with a heavy-duty silicone grip guard allowing comfortable and quick tool-free operation. Specs: Stainless steel and silicone construction Silicone O-ring seal is retained for perfect positioning but is easily cleaned or replaced 1/4" (6.35mm) OD barb tail KegLand Part Number: KL31608

Read more less

High temp silicone grip provides a cool touch even with hot liquids! Ribbed grips allow quick comfortable tool-free operation Fits all male 1/2" NPT and BSP fittings 9.5 mm Duotight compatible stainless steel barb tail The KegLand Stainless Steel Quick Connectors come with a heavy-duty silicone grip guard allowing comfortable and quick tool-free operation. Specs: Stainless steel and silicone construction Silicone O-ring seal is retained for perfect positioning but is easily cleaned or replaced 3/8" (9.5mm) OD barb tail KegLand Part Number: KL31622

Read more less