Beer Making

NOTE: This accessory is designed exclusively for 3-vessel brewers who want to use the BrewZilla or DigiBoil as a mash tun. It is not meant to be used alongside a malt pipe, and it is not intended to be an upgrade or replacement to the BrewZilla's standard false bottom protection screen. If you're a 3-vessel brewer and want to use the BrewZilla or DigiBoil purely as a mash tun, this is false bottom will give you more volume compared to mashing with a malt pipe. Designed for use with DigiBoil electric kettles or BrewZilla all-in-one systems. Unlike two-piece false bottoms you may find, this unit is welded together for maximum strength. It will easily withstand as much grain weight as you could possibly fit in the vessel. Features welded handles to easily remove the false bottom when cleaning. Compatible with 35L DigiBoils and Gen 3/4 35L BrewZillas. Dimensions: Diameter: 11.61" (295 mm) Height: 1.77 (45 mm) Approximate Dead Space: 0.79 gal (3 L) KegLand Part Number: KL27700  

Read more less

Replacement seals for 6m² Two Stage Heat Exchanger sized for 15 to 30 bbls.  

Read more less

Replacement seals for 3m² Two Stage Heat Exchanger sized for 3.5 to 15 bbls.  

Read more less

Swivel nut for 1/4 in. flare fitting connections. For use with 5/16 in. barbs (KEG1109). If you're connecting to stainless steel or brass, you will also need a nylon flare washer to form a seal. Made from nickel plated brass. Comes in a convenient zip lock bag.

Read more less

Stainless steel 5/16 in. barb for flare fitting connections. For use with 1/4 in. swivel nut (KEG1110). If you're connecting to stainless steel or brass, you will also need a nylon flare washer to form a seal. Comes in a convenient zip lock bag.

Read more less

Swivel nut for 1/4 in. flare fitting connections. For use with 1/4 in. barbs (KEG1108). If you're connecting to stainless steel or brass, you will also need a nylon flare washer to form a seal. Made from nickel plated brass. Comes in a convenient zip lock bag.

Read more less

Replacement keg posts (body connects) for ball lock homebrew kegs. Bev Out side. This piece is where ball lock quick disconnects attach to your homebrew keg. The Bev Out post is identified by the smooth sides around the base whereas the Gas In post is notched. Made from stainless steel. Comes in a convenient zip lock bag.

Read more less

Compatible with either your sanke keg coupler or draft shank and held in place with a hex nut & gasket. This 5/16 in. tailpiece is commonly used with 1/4 in. ID draft tubing for a tight fit. Comes in a convenient zip lock bag.

Read more less

Compatible with either your sanke keg coupler or draft shank and held in place with a hex nut & gasket. This 1/4 in. tailpiece is commonly used with 3/16 in. ID draft tubing for a tight fit. Comes in a convenient zip lock bag.

Read more less

Connect draft tubing to your keg coupler or faucet shank. Recommended for 3/16" or 1/4" ID draft lines. Tailpiece and hex nut are made of stainless steel.

Read more less

Replacement probe washers for D-Style Sanke keg couplers. Comes in a convenient zip lock bag.

Read more less

Replacement body washers for D-Style Sanke keg couplers. Comes in a convenient zip lock bag.

Read more less

For repairing a broken tap handle of building one from scratch. The tap ferrule is the piece you'll see at the bottom of most tap handles and is where the handle is screwed onto the faucet lever. You will also need hanger bolts (D2532) to screw the ferrule into a wood tap handle. 5/16" top threads and 3/8" bottom threads. Pack of 5. Comes in a convenient zip lock bag.

Read more less

Chrome plated brass shank comes with a back nut, plastic collar, and a welded 3/16" nipple. This beer shank is a popular choice for building your own custom draft system. Typically installed in the door of a refrigerator or the wooden collar of a converted chest freezer.  The shank’s listed size refers to the total length of threaded pipe. Approximately 1-1/8” are needed to account for the thickness of the finishing collar on the front and the space for the locknut on the back. Please take this into account when sizing the shank for your project. Installation Note: On a fridge there are generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. Dimensions: 4-1/4" - Total Length (Tip to Tip) 3-1/2" - Shank Length (Without Nipple) 2-5/8" - Thread Length 2-3/8" - Pass Through Length 3/16'' - Bore

Read more less

Stainless steel shank comes with a back nut, plastic collar, and a 3/16" tailpiece with hex nut and gasket. If desired, the barb can be removed and swapped for a different size or replaced with a Duotight x Beer Thread Adapter. This size of beer shank is a popular choice for building your own custom draft system. Typically installed in the door of a refrigerator or the wooden collar of a converted chest freezer.  The shank’s listed size refers to the total length of threaded pipe. Approximately 1-1/8” are needed to account for the thickness of the finishing collar on the front and the space for the locknut on the back. Please take this into account when sizing the shank for your project. Installation Note: On a fridge there are generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. Dimensions: 4-1/4" - Total Length (Tip to Tip) 3-1/8" - Shank Length (Without Nut & Nipple) 2-1/4" - Thread Length 1-3/4" - Pass Through Length 3/16" Nipple

Read more less

Silicone regulator stem o-ring. Commonly used on Taprite regulators which have an o-ring located where the regulator stem mates with the CO2 cylinder.  Comes in a convenient zip lock bag. NOTE: These are not intended for use with the KOMOS CO2 Regulator. For the correct KOMOS Regulator replacement gasket, please see D1089.

Read more less

Don't let fruit flies invade your you beer taps in between uses. Slip on this rubber cap to keep bugs out and drips off your floor or counter. Pack of 4.

Read more less

Made from high quality 304 Stainless Steel, this condenser lid is ideal for apartment or basement brewers who struggle managing steam and condensation during brewday. Easy to use and assemble, can be used with a wide range of configurations. Comes with removable end cap for adding hops, yeast nutrient or whirlfloc during the boil. (Use gloves, it will be hot!). This steam condenser set can be compatible with the 35L or 65L BrewZilla/DigiBoil with the stainless distillation lid and 2 Inch Bulkhead. This unit can allow brewing indoors without that pesky sticky steam gumming up your freshly painted interior! The End Cap can be removed for brewing salts/hops and other brewing essentials to be added during the boil. Please note hot steam through this port can lead to serious scalding, please use heatproof gloves. With the new Pro Distillation Lid, the condenser can be attached directly to the 35L unit's 2" T.C. ferrule or to the 65L unit's 4" T.C. ferrule using a 4" x 2" T.C. reducer. The Pro Distillation Lid also features a 3" sight glass disc that can be removed to address foaming issues or to add hops or other boil additions. Not only will you get to the boil faster, but you will use less power overall to maintain a rolling boil as there will be less area for the heat to escape. No need to install inside a kitchen, or in the garage with a special range hood. Simply attach this to the Condenser Lid and run your kitchen tap or garden hose to the Duotight-compatible inlet. You don't not need super-fast flow rate to cool boiling steam into liquid. Different to distillation where you require the distillate to be under a certain temperature so that ethanol doesn't evaporate from the liquid at a high rate, with boiling wort you just need enough to form a liquid! Pretty simple. Eco-Friendly option if you have the means to save/collect the coolant water. Can be re-used on the garden or for cleaning later on. Please note the water discharging will be very hot! The Spray head can condense 0.42 gal (1.6 L) per minute while connected to 100 psi mains water. Caution: You will need to remove the Steam Condenser when you reach boil to manage the hot break and ensure you don't have a boil over when you reach boiling temperatures. Once you've completed that step, you can reattach the Condenser and leave it in place for the remainder of the boil. Warning: It is important that the output tube for this steam condenser is open to atmosphere. This will allow the condensed steam to exit freely. DO NOT put a valve on the liquid output or restrict the condensed steam in any way as this may cause your brewery to develop vacuum and implode or explode. DO NOT immerse the tube for the condensed steam in water. The outlet hose must be open to atmosphere and the drips of condensed steam must drip into your collection bucket freely. You Will Also Need: Tri-Clamp Distillation Lid OR Standard Distillation Lid for 35L or 65L BrewZilla / DigiBoil With 2" T.C. Weldless Bulkhead (H707) OR Pro Distillation Lid for 35L or 65L BrewZilla / DigiBoil 35L Lid connects directly 65L Lid requires 4" x 2" TC Reducer 6.35 mm Monotight Adapter (or you can clamp directly to the inlet) Kit Includes: 5 x 2" Tri-Clamps 5 x 2" Tri-Clamp Silicone Seals 1 x 13.7" (340 mm) Long 2" T.C. Tee  1 x 7.8" (200 mm) Wide 2" T.C. Tee 1 x 2" T.C. End Cap 1 x 2" T.C. to 6.35 mm Monotight elbow cap with elongated spray head mister 1 x 2" T.C. x 0.47" (12 mm) Barb – Suitable for 3/8" (10 mm) ID Silicone tubing Some of these fittings are not sold separately NOTE: The kit does not include the Monotight adapter and garden hose QD shown in the example photo. The text in the photo showing the Duotight compatible inlet elbow states 6.5 mm; it is actually 6.35 mm. KegLand Part Number: KL22842

Read more less

Anvil Foundry Recirculation Pump Kit for 18 gal units.   Features: Anvil Recirculation Pump 4 ft. of Silicone Hose 4 Hose Clamps Flow Clamp Stainless Return Tube Perforated Disc Eye Bolt & Nuts for Eye Bolt

Read more less

Replacement black PCO1881 cap for the FermZilla lid. This is the cap with airlock hole and grommet. For the solid cap, see here.  

Read more less

Replacement black PCO1881 cap for the FermZilla lid. This is the solid cap. For the replacement cap with airlock hole and grommet, see here.  

Read more less

Due to high demand, the pallet qty is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more in mid December.     The Quantor MiniChilly 17 is highly recommended by Brewtools for chilling their F-series Unitanks. These glycol chillers are compact, high-quality units often used in professional settings. Made from stainless steel components and easy to install. They feature an integrated pump with a stirring function that ensures even temperatures throughout the reservoir. Rather than individual pumps for each fermenter, this unit is intended to be provide cooling solution to a single chilling loop where each fermenter will call for glycol circulation independently via solenoid valves. The MiniChilly 17 is recommended for up to 8 x 150L fermentation tanks of which 3 are cold crashed, or up to 4 x 300L fermentation tanks of which 1 is cold crashed. Check out the Brewtools cooling system page for setup details and recommended accessories for building a chilling loop with the MiniChilly 17. Specifications: Controller: EWplus 961 Power connector: Schuko - C19 Power: 790W (1+ HP) Refrigerant: R290 (Propane) Cooling capacity @ 32°F: 1000W (3412 BTU/hr) Cooling capacity @ 59°F: 1650W (5627 BTU/hr) Tank volume: 12.68 gal Dimensions: 29.5" x 16.5" x 23.6" 115V Manufactured in Germany by Quantor/Kreyer. NOTE: The product must stand still 24 hours before use after installation.  

Read more less

Compatible with the 27L and 55L FermZilla Tri-Conical Series or any 3" T.C. fittings. This can be used on the bottom of your conical for a maximized dump valve or it can be used with a FermZilla T.C. Pressure Lid with 2" x 3" reducer and sight glass to make a massive hop injector. KegLand Part Number: KL27571

Read more less

Compatible with the 27L and 55L FermZilla Tri-Conical Series or any 2" T.C. fittings. Primarily designed to be used with the FermZilla T.C. Pressure Lid and 2" Hop Bong for oxygen-free dry hopping. If you're planning on putting your FermZilla Tri-Conical or All Rounder in a Fermentation Chamber, you will want to allow for 420 mm (16.5") of clearance measured from the base of the ring collar to a comfortable level below the chamber ceiling so you can pull the PRV to purge oxygen from the hop bong. KegLand Part Number: KL27564

Read more less