Beer Making

Designed specifically for mounting the NukaTap Mini Beer Faucet on any kegerator, keezer, cold room wall, or other flat surface Connect beer line directly to the faucet, reducing the amount of temperature loss to a standard draft shank No spinning faucets. Your tap will remain in a fixed orientation once locked into the collet Easy installation. No need to drill a large hole through your fridge to accommodate a standard 5/8" draft shank Use with 6.35 mm OD EVABarrier draft tubing This shank kit is specifically designed to suit the NukaTap Mini Beer Faucet and will allow you to connect the NukaTap Mini to a cooler box, kegerator, keg fridge, cold room wall or any other flat surface. This wall mount shank kit is for use with 6.35 mm OD EVABarrier. For the shank kit for use with 8 mm OD EVABarrier, see here. New Innovative Shank Design  Unlike other shank kits, this kit doesn't use a bulky 5/8" threaded shank. The issue with a standard draft shank is that acts as a heat sink, and due to the fact that most shanks sit inside an insulated wall, this results in a substantial amount of warm beer coming out of the tap before cold beer starts flowing. This results in substantial "first pour foam" effect which wastes beer, can result in sour beer, and ultimately negatively effects the quality of the beverages being served. This new design has the beer line feed all the way directly up to the back of the faucet, greatly reducing the volume of non-refrigerated beer. No Spinning Shanks If you have ever installed a traditional 5/8" long shank, you will know how frustrating it is when you use the faucet and it starts rotating. This new design of shank alternative uses three screws that lock the tap into a fixed position and prevents the taps from rotating. If you loosen the 1/2" stainless tap collet you can still have the flexibility to rotate the faucet to any orientation, but once the collet is tight, interlocking teeth on this shank kit and the NukaTap Mini will hold the tap permanently in the correct orientation.  Easy Installation Another advantage compared to standard shanks is that this kit doesn't require you to drill a large 3/4"-1" hole through the wall. As no shank is required, only a hole large enough to accommodate the beer line is required. As a result, an 8mm (5/16") conventional drill bit is all that is necessary for installation. However, if you are concerned about the small amount of beer sitting in the draft line inside the wall not being refrigerated, you can also shell out a larger diameter of foam on the inside of the wall to allow cold air to circulate around the beer line thus reducing the non-refrigerated beer in the line even more. If you wanted to do this the Step Drill Bit is the best tool for the job. Any Wall Thickness Other shank kits will require you to purchase a specific length shank for a specific wall thickness. This new shank alternative will fit any wall thickness. If you have wall thicknesses that are less than 2.7" thick then you can use the included screws that have "snap off" points so you can simply cut the screws down to the desired length. However, if the wall is thicker than 2.7" you can simply purchase a conventional screw from the hardware store and screw the shank kit to your wall. If the substrate is firm enough you may not even need to go all the way through the wall so a common 1-1/4" long screw may be all that is required. Specifications: Beer Line Diameter: 6.35 mm OD EVABarrier Collet and Screw Cover: 304 Grade Stainless Steel O-ring Material: Dual O-ring Silicone/EPDM combination Plastic Mounting: Polyketone (POK) Temperature Range: 14-212°F (-10-100°C) Max Pressure: 150 psi KegLand Part Number: KL32193

Read more less

Designed specifically for mounting the NukaTap Mini Beer Faucet on any kegerator, keezer, cold room wall, or other flat surface Connect beer line directly to the faucet, reducing the amount of temperature loss to a standard draft shank No spinning faucets. Your tap will remain in a fixed orientation once locked into the collet Easy installation. No need to drill a large hole through your fridge to accommodate a standard 5/8" draft shank Use with 8 mm OD EVABarrier draft tubing This shank kit is specifically designed to suit the NukaTap Mini Beer Faucet and will allow you to connect the NukaTap Mini to a cooler box, kegerator, keg fridge, cold room wall or any other flat surface. This wall mount shank kit is for use with 8 mm OD EVABarrier. For the shank kit for use with 6.35 mm OD EVABarrier, see here. New Innovative Shank Design  Unlike other shank kits, this kit doesn't use a bulky 5/8" threaded shank. The issue with a standard draft shank is that acts as a heat sink, and due to the fact that most shanks sit inside an insulated wall, this results in a substantial amount of warm beer coming out of the tap before cold beer starts flowing. This results in substantial "first pour foam" effect which wastes beer, can result in sour beer, and ultimately negatively effects the quality of the beverages being served. This new design has the beer line feed all the way directly up to the back of the faucet, greatly reducing the volume of non-refrigerated beer. No Spinning Shanks If you have ever installed a traditional 5/8" long shank, you will know how frustrating it is when you use the faucet and it starts rotating. This new design of shank alternative uses three screws that lock the tap into a fixed position and prevents the taps from rotating. If you loosen the 1/2" stainless tap collet you can still have the flexibility to rotate the faucet to any orientation, but once the collet is tight, interlocking teeth on this shank kit and the NukaTap Mini will hold the tap permanently in the correct orientation.  Easy Installation Another advantage compared to standard shanks is that this kit doesn't require you to drill a large 3/4"-1" hole through the wall. As no shank is required, only a hole large enough to accommodate the beer line is required. As a result, an 8mm (5/16") conventional drill bit is all that is necessary for installation. However, if you are concerned about the small amount of beer sitting in the draft line inside the wall not being refrigerated, you can also shell out a larger diameter of foam on the inside of the wall to allow cold air to circulate around the beer line thus reducing the non-refrigerated beer in the line even more. If you wanted to do this the Step Drill Bit is the best tool for the job. Any Wall Thickness Other shank kits will require you to purchase a specific length shank for a specific wall thickness. This new shank alternative will fit any wall thickness. If you have wall thicknesses that are less than 2.7" thick then you can use the included screws that have "snap off" points so you can simply cut the screws down to the desired length. However, if the wall is thicker than 2.7" you can simply purchase a conventional screw from the hardware store and screw the shank kit to your wall. If the substrate is firm enough you may not even need to go all the way through the wall so a common 1-1/4" long screw may be all that is required. Specifications: Beer Line Diameter: 8 mm OD EVABarrier Collet and Screw Cover: 304 Grade Stainless Steel O-ring Material: Dual O-ring Silicone/EPDM combination Plastic Mounting: Polyketone (POK) Temperature Range: 14-212°F (-10-100°C) Max Pressure: 150 psi KegLand Part Number: KL32186

Read more less

This Duotight 8 mm (5/16") adapter is designed to suit the Nukatap Mini and will allow you to couple the faucet to a wide range of other 8 mm Duotight fittings. This includes attaching it to the Duotight Flow Control Ball Lock Disconnect. This particular type of flow control ball lock disconnect includes a "tang" at the top of the push in fitting that couples with this adapter. The combination of the two fittings prevents the faucet from spinning around while in use. Sold Separately: NukaTap Mini Beer Faucet (D1598) Flow Control Ball Lock Disconnect (DUO159) Mini Self Closing Spring (D1598A) KegLand Part Number: KL32209

Read more less

The ultimate portable draft faucet! Compact & lightweight with all the advantages of a standard NukaTap forward sealing faucet Pair with a Flow Control Ball Lock QD & Duotight Adapter and the whole assembly fits in your pocket Forward-sealing design prevents beer residue from gumming up the faucet Reduced first pour foam due to low thermal mass and conductivity Perfect for mobile draft, mini kegs, sampling from fermenters, and can even be installed on your kegerator or keezer Mini Design – Ideal Flow Rate for Small Systems Most conventional beer faucets are designed with 3/8" diameter spouts so you can pour a pint in just over 10 seconds. This type of flow rate is great for high turnover bars and commercial venues but isn't necessary or even desirable for all applications. For compact portable systems and home draft systems, a slower flow rate is easier to control and further reduces foaming issues due to the low liquid volume stored in the body of the faucet. The NukaTap Mini is also more ideal for pouring smaller doses. For example, cocktails where 5-8 oz of liquid is dispensed is difficult to control with a high flow rate tap. For portable systems, the NukaTap Mini with the Flow Control Ball Lock QD & Duotight Adapter assembly is small enough to literally put in your pocket, making it ideal for mini keg setups that you want to be portable or that you want to easily fit inside a domestic fridge where space is tight. Forward Sealing Forward sealing faucets are absolutely the way to go when it comes to beer taps. Old legacy taps still exist in the industry that are simply poorly designed. The issue with rear sealing faucets is that beer dries up on the internal piston. Aside from being unsanitary, as more and more beer dries up in these components the faucet can almost glue completely shut causing damaged seals or broken handles (this is particularly the case if it's left for some time to dry out with beer inside). These older legacy designs still exist probably due to poor education. The forward sealing designs do not have this problem and the tap drains out completely with no beer drying up on the mechanical moving parts in the same way. This makes the tap more sanitary and reduces maintenance. In many instances the price is similar so there is no reason to use a poorly designed rear sealing faucet. All NukaTap faucets are forward sealing. Laminar Flow Just like the NukaTap SS and NukaTap FC, the NukaTap Mini has been designed with laminar flow in mind. Laminar flow is critical for a beer tap as it means you will pour the beer with minimal foaming and a substantial reduction in wastage. Think about how many times a beer faucet opens and closes in its lifetime. 1,000 or maybe 10,000 times?  Laminar flow saves wasted beer in excessive foam and the better laminar flow easily pays for itself in a reduction in lost beer. To use poorer designed faucets is essentially flushing money down the sink. Extensive modeling has been done on the NukaTap design to improve laminar flow. Integrated Seals That Are Indestructible and More Sanitary Unlike other designs, the NukaTap Mini body is made from Polyketone (POK) making it strong, robust, and able to be autoclaved. The seals are also over-molded from Santoprene® making them hard wearing so they will literally last for the lifetime of the tap without the need for replacement. Santoprene® and POK both have excellent resistance to chemicals such as caustic soda, peroxide, phosphoric acid, lactic acid, citric acid, acetic acid, and all common chemicals sold and used in the beverage industry. The seals internally are over-molded meaning no fissures or cracks exist for bacteria, crud, or yeast to hide. Superior First Pour Foam Due to Low Thermal Mass and Conductivity First pour foam is an issue caused by a warm tap body. For most faucets to pour well it's important to dispense enough beer to cool the tap body down to reach maximum performance. In addition to this the conductivity of the tab body also makes this worse so insulative materials simply work better than conductive materials. The NukaTap mini not only has very low thermal mass but is also highly insulative being made mostly from Santoprene® and POK. The combination of these two factors in conjunction with superior laminar flow makes for the lowest "first pour foam" effect out of any tap ever produced. Long Shank Alternative Most conventional beer faucets require a large 3/4" hole to be drilled through the side of your refrigerator, keezer, or cold box wall. Traditional long shanks also generally have a large volume of liquid that sits inside the wall unrefrigerated which is not ideal. New long shank alternatives developed for the NukaTap Mini are designed to suit any wall thickness and greatly reduces the stagnant beer sitting in the shank itself. For walls up to 2.7" thick, these wall mount shank kits include three screws, however if the wall is thicker, you can also use 6 small wood screws or something similar and attach three screws from the front and 3 from the back allowing you to go into any wall type. Another advantage of this new design is the tap will never accidentally rotate. Typically, other long shank beer taps rely on the hex nut on the shank to be done up tight enough to prevent rotation but if the wall compresses (often the case with foam walls) the tap is allowed to rotate. This new design has three fixing points making it impossible for the tap to rotate accidentally as the interlocking teeth behind the collet allow you to set the angle and then do up the collet to fix the tap permanently in that position. NukaTap Mini Accessories (Sold Separately): Duotight Flow Control Ball Lock QD (DUO159) Mini Self Closing Spring (D1598A) Duotight Adapter - 8mm (D1598B) Long Shank Alternative for Wall Mounting - Duotight 8mm (D1598C) Long Shank Alternative for Wall Mounting - Duotight 6.35mm (D1598D) Stout Spout (D1598E) Vertical Clamp On Assembly (D1598G) Horizontal Clamp On Assembly (D1598H)

Read more less

The KOMOS Deluxe Kegerator model boasts the same features as the standard model with an eye-catching stainless steel extrerior and upgraded stainless steel drip tray. The interior fits up to four 5-gallon ball lock corny kegs at one time. These units were designed by homebrewers for homebrewers. They're built for long lasting service, with high quality stainless steel door and aluminum floor, and rolling casters.  Whether you need to dial in the perfect serving temperature for your beer, or you're looking to hold a 64° fermentation in hot weather, this kegerator has you covered with the integrated extended range thermostat, capable of holding temperatures from 26 - 82°F (the fridge does not provide heating).  Comes with robust KOMOS CO2 regulator included!  The KOMOS Kegerator has a premium feature set for an amazing price, and is a perfect companion to any brewer or beer connoisseur. Features: Digital Thermostat with wide 26 - 82° F temp range. Robust KOMOS Dual Gauge Regulator included CO2 Tank holder mounts on back of kegerator (tank not included) Efficient and powerful compressor Stainless steel door, top cover, and side panels Stainless Countertop Style Drip Tray Aluminum floor for additional keg support Rolling casters You will need to purchase keg connections depending on whether you are serving commercial sanke, ball lock corny, or pin lock corny Specifications: 23.75" wide 25" deep  31.5" with CO2 mount 32.5" Tall 35" with Caster wheels 110 v - 60 hz 0.8 Amp draw Optimal ambient temperature is  65°F – 80°F CSA Certified Internal Dimensions: 19.5" wide 17" deep 16" down the center where compressor sits 28.5" tall What Fits: 5 Gal. Torpedo Keg - 3 5 Gal. Slimline Torpedo Keg - 4 5 Gal. Pin Lock Cornelius Keg (Corny Keg) - 3 5 Gal. Ball Lock Cornelius Keg (Corny Keg) - 4 5.2 Gal. Oxebar PET Keg - 3 or 5.2 Gal. Oxebar PET Keg - 6 5.16 Gal. Sixth Barrel Keg (Sixtel, Log) - 3 7.75 Gal. Quarter Barrel Keg (Pony Keg, Stubby Quarter) - 1 7.75 Gal. Slim Quarter Keg (Tall Quarter, The Slim) - 1 15.5 Gal. Half Barrel Keg (Full Size Keg) - 1 See below for the Kegerator Instruction Manual. (The Deluxe Kegerator does not have feauture a Guard Rail as seen in the residental kegerator instructions.) Please note: This unit requires 4" of clearance on all sides and is not intended to be installed under a countertop. For a build-in unit, see the KOMOS Pro Stainless Steel Kegerator.  

Read more less

Strawberry soda extract from Rainbow Flavors. Concentrated flavor extract for making your own sodas. Mix with water and sugar, then either carbonate by bottle conditioning with yeast, or force carbonate in a keg. One 2 fl oz bottle makes 4 gallons of soda. Recipes and mixing instructions for different size batches are included. One 1 gallon jug makes up to 256 gallons of soda.

Read more less

Munich is characterized by clean, slightly sweet, rich malty flavor and contributes golden amber leaning toward orange hues Can be used as 100% of your fermentable sugar in extract brewing Add for color correction, boost gravity, or improve head retention in all grain brewing Briess Malt & Ingredients has had a focus on quality and innovation for more than 140 years, with all of their products being made in the U.S.A. Concentrated Brewers Wort (CBW) Liquid Malt Extract (LME) from Briess. Briess CBW malt extracts get all of their color and flavor from base and specialty malts, never through additional boiling. CBW malt extracts are unhopped and nondiastatic for flexible, creative brewing. Munich LME: 100% pure malt extract made from 50% base malt, 50% Bonlander® Munich Malt 10L, and water. Typical Analysis: Color (8° Plato): 8 SRM Fermentability: 75% Solids: 79%

Read more less

Traditional Dark has an intense, sweet and malty flavor perfect for Brown Ales, Porters, Stouts, and other malt-forward styles Can be used as 100% of your fermentable sugar in extract brewing Add for color correction, boost gravity, or improve head retention in all grain brewing Briess Malt & Ingredients has had a focus on quality and innovation for more than 140 years, with all of their products being made in the U.S.A. Concentrated Brewers Wort (CBW) Liquid Malt Extract (LME) from Briess. Briess CBW malt extracts get all of their color and flavor from base and specialty malts, never through additional boiling. CBW malt extracts are unhopped and nondiastatic for flexible, creative brewing Traditional Dark LME: 100% pure malt barley extract made from a blend of 100% malts and water. Typical Analysis: Color (8° Plato): 30 SRM Fermentability: 75% Solids: 79%

Read more less

Birch Root Beer extract from Rainbow Flavors. Concentrated flavor extract for making your own sodas. Mix with water and sugar, then either carbonate by bottle conditioning with yeast, or force carbonate in a keg. One 2 fl oz bottle makes 4 gallons of soda. Recipes and mixing instructions for different size batches are included. One 1 gallon jug makes up to 256 gallons of soda.

Read more less

A complete kegging system featuring KOMOS CO2 Regulator, KOMOS CO2 Cylinder, and a brand new ball lock corny keg! Available in 2.5 and 5 gallon sizes, we provide all the equipment you need to get your beer kegged up. Comes with EVABarrier tubing and Duotight ball lock QDs and fittings for easy assembly. Included: KOMOS Dual Gauge Regulator KOMOS 5 lb aluminum CO2 cylinder Ball Lock Corny Keg (2.5 or 5 gal) EVABarrier beer & gas lines Duotight ball lock quick disconnects (QDs) Duotight-compatible plastic picnic faucet KOMOS 7-in-1 Multi Tool Wrench Please note: the CO2 tank ships empty. It can be filled or swapped for a full tank at your local welding or homebrew supply store.

Read more less

Help retain heat with Speidel's insulating jacket for the 50L Braumeister. Fits both new models as well as pre-2015 models.

Read more less

Ferment, cold crash, and carbonate beer all in one vessel with the Brewtools F-Series Unitank Cooling jacket welded to the vertical walls of the tank provide superior cooling capabilities compared to in-solution cooling coils Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use Pressure rated to 30 PSI so you can safely ferment under pressure and pressure transfer finished beer to kegs with virtually no oxygen pickup Brewtools is a Norwegian brand known for high-quality products made without compromise. From brewing systems to fermenters, they continue to push the envelope of innovation for homebrewers around the globe All valves, fittings, and gaskets come included Brewtools Unitanks are fermenters made for ambitious homebrewers and small breweries. As part of the Brewtools identity, they've explored new techniques and solutions. This has resulted in a series of high end fermentation tanks with new features and a lot of possibilities. Key Features: Brewtools PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation. Cooling jacket in the vertical walls offers efficient cooling without the hassle of cleaning a spiral. Many options for connecting accessories like sensors, heaters, carb. stones and other accessories. Pressure rated for 2 bar / 30 PSI Cooling jacket pressure rated for 0.5 bar / 7 PSI 8" TC port on top for easy access. 2" TC dump and racking valves. BrewTools Unitanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party. Specifications: Low height w/o acc.: 66.1" Max height w/o acc.: 74" Packaging size: 70.8" (h) x 28.3" (w) x 28.3" (d) Net weight: 167.1 lbs Gross weight: 209.4 lbs Tank diameter (inside): Ø23.6" Gross volume: 81.8 gal Max rec. volume: 76.6 gal Min rec. volume: 31.7 gal Volume, cone: 10.5 gal Material: 1.5mm stainless steel (SS304) Operating pressure: 1.0 bar / 15 PSI Max pressure: 2.0 bar / 30 PSI In the box: Unitank with adjustable frame 1 pcs Analog pressure gauge, TC34mm 2 pcs Butterfly-valve, 2" 1 pcs Butterfly-valve, 34mm DN20 1 pcs Blow-off pipe 1 pcs Racking arm 2" 1 pcs TC elbow 90°, 2" 1 pcs Insulation jacket, black neoprene 1 pcs Sample valve, 34mm 1 pcs TC Adapter 8"-4" 1 pcs TC blind cap, 4" 1 pcs TC blind cap 2" 2 pcs TC blind cap 1.5" 3 pcs TC blind cap 34mm 2 pcs TC gasket 8" lipped 2 pcs TC gasket 4" 2 pcs TC gasket 2" 5-pack 1 pcs TC gasket 1.5" 5-pack 3 pcs TC gasket 34mm 5-pack 1 pcs Tri Clamp 8" 1 pcs Tri Clamp 4" 5 pcs Tri Clamp 2" 2 pcs Tri Clamp 1.5" 10 pcs Tri Clamp 34mm 1 pcs TC tool 4 pcs M10 steel/rubber feet 1 pcs TC34mm safety valve (PRV, 2 bar) Necessary bolts and parts for assembly 5 year manufacturer's warranty Recommended accessories include: HopDrop-kit, Thermowells for your sensors, 34mm Ball-Lock gas adapter for CO2 filling, Coil for sample valve, Spunding valve, Hose barbs for filling and dumping, etc. For User Manuals and support, please follow this link to Brewtools Docs. NOTE: Model in photo is a prototype. Minor changes and improvements may occur.

Read more less

Caramel Rye Malt provides a candy-like sweetness and the spicy character of rye Can be used in small amounts to add depth and a subtle rye flavor Use as up to 20% of your grain bill in rye beers; commonly used along with Rye Malt and Rye Flakes Briess Malt & Ingredients has had a focus on quality and innovation for more than 140 years, with all of their products being made in the U.S.A. 45 °L - Briess Malting - Caramel Rye Malt is a drum roasted crystallized rye malt that improves foam, enhances viscosity, and contributes golden hues with a candy-like sweetness and the spicy character of rye. You can use this with Briess Rye Malt or Briess Brewers Rye Flakes for more rye flavor, and to complement the smooth and subtle, yet complex, flavor of Briess Caramel Rye Malt and add depth and subtle flavor to many styles of beer. Usage Levels / Beer Styles 1-5%: Adds touches of depth to lighter-flavor beers like Pilsner, Oktoberfest, and Bock 5-10%: Adds complexity to malt-forward beers 10-20%: Adds an intriguing softness and slight rye-like character. Use in all rye-style beers for toast flavor and color as well as in Scottish Ales, Doppelbock, Dunkels, Stouts, Porters, and other medium to dark ales and lagers

Read more less

Pressure activated auto glass rinser. Built for commercial and home bars in mind with an existing water supply and a sink. These compact glass rinsers are capable of withstanding up to 100 psi of pressure from your home's main water supply line. How to Use: Invert glass and empty last drips into sink Press glass onto the center of the glass rinser in short bursts If you have access to an inline carbonated water source, using bubbly water will really give your glasses a stripping clean. This device can also be used with chilled water to cool your glass down in between beverages. Specifications: 1/2" BSP threaded rod for a number of Duotight attachments We recommend PE Water Line and this 1/2" adapter 4.3" H x 4.5" W KegLand Part Number: KL27649

Read more less

The Unitank 2.0 features 50% more cooling surface than the previous generation for better cooling efficiency and crashing performance. Manufactured with professional level quality that has been the standard for Ss Brewtech's professional-level Unitanks New Ss Brewtech Racking Arm co-molded with the geometry of the valve body and TC gasket which prevents the arm from coming loose Quickly carbonate beer in under 24 hours using the carb stone while precisely monitoring head pressure Adding an optional Sspunding Valve to the Unitank gives the brewer the ability to ferment under pressure An evolutionary step forward in homebrew technology. The Unitank 2.0 builds upon the venerable Unitank line by increasing the full body wall thickness from 1.2 to 1.5mm 304 Stainless Steel. Then we added a fully laser welded, professional-grade jacketed cooling solution to the already advanced feature set the original Unitank is known for. With up to 50% more cooling surface area, maintaining a stable temperature and crashing your beer has never been more efficient. Jacketed Cooling The benefits of jacketed cooling are numerous, and such engineering has become the standard in Ss Brewtech professional Unitanks for years. With Unitank 2.0, those same benefits are available to the 5, 10, 15 and 31 gal home or nano brewer. When paired with FTSs Touch and Ss Glycol Chillers, the Unitank 2.0 can provide an uncompromised level of fermentation control. The increased surface area of jacketed cooling allows more precise temp control not seen in the home brew industry. Additionally, the added surface area allows the fermenter to crash cool in even the most challenging environments. Another benefit of moving to jacketed cooling is that removing the coil makes the cleaning process much more straightforward. When used with the Ss Brewtech CIP ball, cleaning can be performed just as the pros do in craft breweries. Staggered inlet and outlet ports for the glycol jacket help with even coolant distribution in the jacket. The rear-mounted thermowell cleans up the coolant control wiring for an even more professional setup. Keyed Racking Arm Like the Chronical 2.0, the Unitank 2.0 features a version of the new Ss Brewtech Racking Arm co-molded with the geometry of the valve body and TC gasket; this ingenious design captures the racking arm and prevents it from coming loose. Additionally, the keyed elements of the valve allow the brewer to know precisely what direction the racking arm is facing based on the orientation of the valve on the vessel. What's more, the Unitank valve is the same full pressure-rated valve used on professional Ss Brewtech equipment. All the Valves & Ports The Unitank 2.0 continues with all the beloved features of the original Unitank. On top of all the fully welded TC connections and pro features, the Unitank 2.0 allows the brewer to quickly carbonate beer in under 24 hours using the carb stone while precisely monitoring head pressure. After fermenting and carbonating, the brewer can perform a true pressurized and closed transfer to a keg or canning machine significantly reducing the chances of oxidation when compared to open transfers. Higher pressure limits allow the user to dispense beer directly out of the vessel. Lastly, adding an optional Sspunding Valve to the Unitank  gives the brewer the ability to ferment under pressure and gives them the option to use the final few gravity points left of active fermentation to naturally carbonate their beer instead of force carbonate. This feature set and flexibility are why pro brewers use Unitanks in their brewing and packaging processes. Features: Welded Cylinder Glycol Jacket Fully welded TC flanges 15 PSI operating pressure Rotatable Silicone Racking Arm 1.5” TC Butterfly Valves 1.5” TC Carb Stone with 3/8” ball valve 1.5” TC Blow Off Arm with Welded Blow Off Arm Mount 1.5” TC to ½” Ball Valve for Blow Off Cane 1.5” TC Pro Sanitary Pressure Gauge 1.5” TC Pro Sanitary Sampling Valve 1.5” TC Thermowell 3” TC Pressure Relief Valve (PRV) 6” TC to 3" TC Lid Reducer (Dry Hop, CIP, and PRV Port) Neoprene Insulation Jacket Stainless Lower Shelf Adjustable Feet

Read more less

Used – Refurbished This unit is used. It has been restored to working order. It will have cosmetic defects and show signs of previous use. It is still covered by our No Hassle Return Policy and 1 Year Warranty Policy.   Replacement malt pipe for the 200L Braumeister

Read more less

This keg opening tool attaches directly to a 1/2" drive so it can be used with an impact driver or pneumatic rattle gun. This makes fitting and removing keg spears really fast and can save a ton of time when working with a high volume of kegs. Compatible with D-Style and S-Style kegs with threaded spears. There are two styles of Sanke kegs, those with a threaded-in spear and those that use a retaining ring, or circlip, to hold in the spear. This tool is designed for use with D- or S-Style Sanke kegs with threaded spears. For the more popular (in the USA) D-Style circlip-style Sanke kegs, use tool KEG860. Please Note: this tool does not remove the retaining ring. Once the keg has been depressurized, you will have to remove the ring by hand. KegLand Part Number: KL14908

Read more less

Clean multiple beverage draft lines in a single loop using this Ball Lock Keg Jumper Post. Makes cleaning your kegerator or keezer a breeze without the need to remove your quick disconnects. This double ended keg post does not have a spring & poppet. It just has a piece of bar that activates the ball lock disconnect wide open. Please note it is a single piece that cannot be undone from the middle. KegLand Part Number: KL20152

Read more less

This handy kit contains all the seals needed for a NukaTap Counter Tap Bottle Filler. Includes: (1) Bleed Valve Seal (1) 1/4" Male Thread Seal (2) Push-in Barb Seal (3) Gas Purge Valve Seals The majority of these seals in the NukaTap Counter Pressure Bottle Filler would never normally need to be replaced. But in the event of accidental loss or damage, please replace the seals with the addition of food-grade lubricant to ensure their longevity. KegLand Part Number: KL27632

Read more less

Magnetic drive enables you to slow down the flow without damaging the pump—just add a ball valve to the outlet! T.C. connection allows the pump head to be oriented at any angle in a full 360-degrees Pull ring PRV at the pump outlet makes it easy to purge air and prime the pump before each use Inline flow path for smooth integration into your brewery while keeping your tubing lines tidy Stainless steel head with 1/2" threaded ports to attach your preferred fittings—tri-clamp, quick disconnect, camlock, and More! The best-selling MKII Magnetic Drive Pump now available with a major upgrade! This unit comes standard with an inline stainless steel pump head that installs on the pump body with a 3" tri-clamp. Compared to the standard "center inlet" pump head, the "inline" flow path can make it much easier to integrate into your brewery and keep your brewing hoses tidy. At the outlet of the pump, there is a very handy pull ring PRV that allows you to bleed liquor or wort from the pump head to release trapped air and prime the pump. And with the 3" T.C. connection, not only do you have a full 360-degrees to orient the pump head any which way, cleaning the pump after use could not be easier—just pop off the tri-clamp, wash out the pump head, and clamp back on. The MKII is a perfect pump for your system and comes highly recommended for brewers stepping up to all-grain brewing. Rather than schlepping heavy kettles filled with hot liquor or wort around your brewery, or awkwardly stacking them into a 3-tier gravity setup, allow this handy pump to move liquid from vessel to vessel while everything remains in place. The magnetic drive allows you to slow down the flow without damaging the pump. This can be done by attaching a ball valve to the outlet side of the pump, and then you simply open or close the valve to control the flow rate. The pump itself is not self-priming, but priming is super easy thanks to the pull ring PRV which will help ensure the pump head is full of liquid and trapped air is released before powering it on. Tri-Clamp Pump Head The T.C. pump head can be removed quickly and easily using the 3" tri-clamp. This means no drivers or power drills are needed to back out the six Phillips head screws that mount the pump head on the standard version of the MKII. Whip the head off in a flash to clear out spent grain, hop material, or clear a blockage. Attaching the pump head with a tri-clamp also allows the head to be rotated at any angle in a full 360-degrees. This makes it easy to configure the plumbing to your unique brewery setup. Inline Design An "inline" pump head simply means the input and output are on a straight horizontal line with one another which can make it easier to integrate into your brewery setup. If you're using a 3-vessel horizontal system, the inline pump head will make it easier to keep your hoses neat and tidy compared to pumps heads with a center inlet. PRV Purge Valve The corny keg style PRV will make priming the pump a breeze. Simply let bleed the pump head to purge air out before turning the pump on and you'll avoid any cavitation issues. The PRV also acts as a safety so you do not over pressurize your pump head or brewery system. 304 Stainless Steel The entire pump head is made from 304 grade stainless steel so it's highly resistant to chemicals, heat, and physical abuse. The 1/2" BSP threaded ports can be used to attach barbs, quick disconnects, camlocks, tri-clamp adapters, or any other 1/2" fittings you prefer. Features: 110V / 60hz Max Head: 11.15 ft. (3.4 m) Max Flow: 5 Gal/min (19L/min) Max Temperature: 248°F (120°C) 360° rotatable stainless steel pump head 1/2" BSP ports Water resistant casing (not waterproof) KegLand Part Number: KL27236 If you're brewing on a budget and want the most affordable pump possible, check out the standard model MKII pump. This has been our best-selling pump for years and you can always upgrade it down the road with the standard stainless center inlet head or inline stainless tri-clamp head.

Read more less

Get your brew day started faster with the MB commercial grain mill—process an entire pallet of malt in an hour! Adjustable grain flow rate to slow the mill down to match your mashing speed Differential roller speed applies enough force to open the grain kernels as they pass through the rollers without damaging the husk, improving efficiency and lauter performance Slotted rollers more effectively expose the starchy endosperm inside the kernel compared to knurled rollers Rollers made from steel alloy which is harder and longer lasting than stainless steel 0.4mm to 1mm (.016"-.039") mill gap is easily dialed in with handled adjustment wheels Professional quality grain mill with stainless steel construction throughout The MB commercial-grade mill can process upwards of 2,000 lbs of grain per hour and features large diameter slotted alloy rollers for an excellent crush and long life. This mill can easily power through whatever you throw at it, including barley, wheat, rye, and corn. Differential Roller Speed Rotating the rollers at different speeds is the key to a superior crush. Standard grain mills rotate the rollers at the same speed, creating a pinch point between them where the grain kernels are cracked open. Although effective, this can often lead to an excess of flour and damaged grain husks. The MB pro mill drives the rollers at different speeds to apply enough force to open the grain kernels as they pass through the rollers without damaging the husk. This action results in a better crush that will improve efficiency and lauter performance. Slotted Rollers Many grain mills feature hardened steel knurled rollers due to the lower cost, but they don't provide the best crush possible. Rather than shredding the grain into submission, slotted rollers (also known as fluted rollers) are more effective at shearing the grain husk to expose the endosperm while leaving the hull intact. The rollers are made from steel alloy which are harder and longer lasting than stainless steel. This roller features a 155mm diameter, which lowers the angle of attack on the kernel and allows the mill to pull grain more efficiently. Professional Quality The MB pro mill is an industrial workhorse and the best value for a commercial mill on the market. The hopper capacity is 55 lbs of grain and large adjustment wheels make for easy gap adjustments. Stainless steel construction throughout, and anchor holes in the feet allow the unit to be bolted to the ground. Specifications: Processing Speed: approx. 2,200 lbs/hr Hopper Capacity: 55 lbs Voltage: 208V/220V 3-phase motor Power: 4 HP Amperage: 8.3 amps Mill Gap: 0.4mm - 1mm Mill Roller Size: 155mm diameter, 110mm long Please Note: The unit will arrive bare without a power cord, plug, or controls to power the motor on or off. You will need an electrician to wire the appropriate power cord and shutoff switch to the motor. Please Note: This unit REQUIRES 208-220V Three Phase power and will not function on anything else. Please confirm that you have the proper power for this unit before purchasing, and plan to have a qualified electrician install a fused shutoff and wire directly to the included on/off switch.

Read more less