Beer Making

Due to high demand, the 7 bbl and 10 bbl are currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more in late July. Oil-based brewing system that closely mimics a large-scale steam-powered system Heated oil is circulated around jacketed tanks to heat with a large surface area. All the benefits of steam without the complexity of a steam generator Lower electrical requirement for installation compared to electric brewhouses with immersion elements Insulated vessels for high heating efficiency Compact brewing system with no need for additional electrical controllers, components, or extensive wiring. All pumps, piping, and fittings included No heating elements in direct contact with wort. Zero risk of scorching and easy to clean 1 bbl to 3.5 bbl systems available with or without mash rake. 5 bbl and above come with mash rake as standard 7 bbl systems and above feature a brew deck and CIP ring below the mash tun to clean the underside of the mash screen 3 Vessel systems are ideal for breweries that intend to use this unit as their primary brewing system 208V, 3-phase power is the standard configuration for all systems. Customized power configurations available upon request (see below) For detailed power specs, dimensions, and shipping quotes contact our MoreBeer! Pro sales representatives today! Compared to the traditional steam heating brewhouse, the creative new-tech thermal oil heating avoids the installation of a dangerous and high-maintenance steam boiler. Steam offers more surface area than gas fired, but it requires a generator to create steam, collect it, and reheat it again. Oil heated brewhouses, on the other hand, use a simple oil heater and pump to circulate oil through the tank jackets. Compared to gas fired systems where all heat is directed to the very bottom of the kettle, this system heats from the sides and the bottom rather than the bottom alone. This offers not only greater surface area but faster thermal response. By controlling the oil temperature, you also have more precise boil vigor control and evaporation rate control. For these reasons and more, the Oil Heated Brewhouse makes for an ideal pilot batch system. Control Panel Our control panel features 4 PID controllers for precise control of the HLT, Mash, Boil Kettle and Oil temperature. The control panel also features a delayed start timer, allowing you to preheat your HLT overnight so your strike water will be ready when you arrive on brew day. Hard Piped Distribution Manifold With the distribution manifold, the entire brewing process can be completed by simply opening and closing valves. There’s no need to lug around brewery hoses and swap connections from vessel to vessel. This hard piped system is completely self contained with dedicated pumps to move wort and hot liquor from tank to tank as needed. Every step of the brew day is a simple valve turn away. The only hose required is from the brewing system to your fermenter. Once the brew is completed this same piping system is used for CIP and rinsing. Installation The systems are delivered on a skid. Simply, move the skid into place, hook up power and water and a drain and you are ready to clean and brew. Our systems also feature rolling casters for easy installation in your brewery, product pump for recirculation and sparging, hard piped manifold, grain out door on the mash tun, and mounted plate chiller. Design Features: 3-Vessel System with dedicated HLT, Mash Tun, and Boil Kettle Compact design and easy installation Built-in wort pump Built-in HLT pump Built-in 2-stage heat exchanger Hard piped distribution manifold Built-in control panel PID controls for kettle temperatures and oil temperature Slotted Mash Screen Tangential kettle return for whirlpool Built-in CIP Water inlet & hot water drain in 1.5" T.C. Insulated tanks for heat retention and heating efficiency Boil kettle features steam collector which eliminates the need to install a flue in your brewery Hot oil vessel can operate at higher temperatures, that means 25% higher heating efficiency: Oil temperature set at 302°F (150℃) [available up to 572°F (300℃)] from 82°F to 140°F (28°C to 60℃), heat-up time: 20 min from 140°F to 176°F (60°C to 80℃), heat-up time: 20 min from 176°F to 212°F (80°C to 100℃), heat-up time: 30 min Higher heating efficiency compared to steam heating Simultaneous heating of HLT, mash tun and kettle to save time 100% 304 Stainless Steel TIG welded tanks Laser welded dimple jacket and tank bottom Manufactured in strictly controlled ISO9001 certified facility 208V, 3-phase power* *MB Stainless offers custom voltage oil systems. 240V single-phase systems available up to 5bbl. MB also produces 480V 3-phase systems in all sizes. Contact our sales representatives for pricing, lead time and delivery information. Food-grade thermal oil not included. We recommend PARATHERM™ MR HTF or an equivalent low odor, food grade, thermal transfer fluid.  

Read more less

The Ultimate BrewZilla Combo Pack! Get the Gen 4 BrewZilla & our most highly recommended accessories at an unbeatable price! Includes all of our favorite accessories for the BrewZilla including the Neoprene Jacket to speed up heating times, Hop Spider to keep vegetal matter out of your wort, and Chilling Connection Kit so you're ready to use the Immersion Chiller out of the box We think all BrewZilla brewers will eventually upgrade their systems with these accessories, so buy them together and reap the savings! Also available in 220V (AG583) Combo Pack Includes: BrewZilla Brewing System | Gen 4 | 9.25G | 110V Neoprene Jacket Hop Spider Wort Chiller Connection Kit Gen 4 BrewZilla All-in-One Brewing System WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet WiFi/Bluetooth Enabled RAPT Controller The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen. But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability. And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer! But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings. Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road. High Capacity Malt Pipe With an approximately 23.5 lb capacity, the BrewZilla can mash nearly 50% more grain than similar sized models of the Anvil Foundry and Grainfather G30. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery’s grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency. Concave Base with Center Draining Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind. Ultra Low Watt Density Elements The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy. Easy Access Built-In Pump The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet. If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer. MoreBeer!'s Final Word We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included. Perfect for Distillation If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find. Features: Gen 4.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons WiFi/Bluetooth Enabled RAPT digital temperature controller Automatic step mashing with 6 programmable stages 110-120V power and plug 12.5A Requires 20A circuit Dual heating elements (1000 watts and 500 watts) Stainless steel 1/2" ball valve for gravity draining or transferring via pump Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Adjustable lid clamps (do not use with glass lid in place - see below) Magnetic drive pump for recirculation, transfers, and cleaning Recirculation arm PPSU sight glass Bottom handle for easy lifting and pouring Rubber feet Temperature reads in °F or °C Approximately 32.75" H (with recirculation arm) x 12.5" D Recommended max. grain bill: 23.5 lbs AlcoEngine Still ready with the purchase of a Distillation Lid Pump Specs: Max Capacity: 2.9–3.1 gal/min Max Head: 4.9–6.8 ft. Poles: 2 Voltage: 110–120V-AC Frequency: 50–60Hz Power: 6 watts Current: 60 mA Speed: 2600–3000rpm Duty Cycle: Continuous Capacitor: 2µF Input/Output: 13mm barb Water Resistance: IPX2 Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos. Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe. Warning:  Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged. Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use.   35L (110V) 35L (220V) 65L (220V) 100L (220V) 10 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 25 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 50 ft. 12 Gauge 12 Gauge 10 Gauge 8 Gauge

Read more less

The Ultimate Grain to Glass Combo Pack! Get the Gen 4 BrewZilla & FermZilla Tri-Conical with all the best accessories at an unbeatable price! Brew extract or all grain batches on the BrewZilla; ferment, carbonate, and serve from the FermZilla. Everything you need from Grain to Glass! Comes with all of the most highly recommended accessories for the BrewZilla, including the Neoprene Jacket to speed up heating times, Hop Spider to keep vegetal matter out of your wort, and Chilling Connection kit so you're ready to use the Immersion Chiller out of the box Includes some of our favorite accessories for the FermZilla, such as the Pressure Kit with Floating Dip Tube so you're always racking the clearest beer and the Duotight BlowTie 2 for pressure fermentations and flow control keg transfers Over $100 savings when purchasing this kit bundle compared to buying everything piece-by-piece! Also available in 220V (AG582) You can search high and low, but you won't find a better deal than the BrewZilla Ultimate Grain to Glass Combo Pack! Combo Pack Includes: BrewZilla Brewing System | Gen 4.1 | 9.25G | 110V Neoprene Jacket Hop Spider Wort Chiller Connection Kit FermZilla Tri-Conical Fermenter | Gen 3.2 | 7.1G Plastic Pressure Kit w/ Floating Dip Tube Duotight BlowTie 2 Spunding Valve Insulating Jacket Gen 4 BrewZilla All-in-One Brewing System WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet WiFi/Bluetooth Enabled RAPT Controller The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen. But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability. And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer! But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings. Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road. High Capacity Malt Pipe With an approximately 23.5 lb capacity, the BrewZilla can mash nearly 50% more grain than similar sized models of the Anvil Foundry and Grainfather G30. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery’s grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency. Concave Base with Center Draining Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind. Ultra Low Watt Density Elements The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy. Easy Access Built-In Pump The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet. If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer. MoreBeer!'s Final Word We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included. Perfect for Distillation If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find. Features: Gen 4.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons WiFi/Bluetooth Enabled RAPT digital temperature controller Automatic step mashing with 6 programmable stages 110-120V power and plug 12.5A Requires 20A circuit Dual heating elements (1000 watts and 500 watts) Stainless steel 1/2" ball valve for gravity draining or transferring via pump Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Adjustable lid clamps (do not use with glass lid in place - see below) Magnetic drive pump for recirculation, transfers, and cleaning Recirculation arm PPSU sight glass Bottom handle for easy lifting and pouring Rubber feet Temperature reads in °F or °C Approximately 32.75" H (with recirculation arm) x 12.5" D Recommended max. grain bill: 23.5 lbs AlcoEngine Still ready with the purchase of a Distillation Lid Pump Specs: Max Capacity: 2.9–3.1 gal/min Max Head: 4.9–6.8 ft. Poles: 2 Voltage: 110–120V-AC Frequency: 50–60Hz Power: 6 watts Current: 60 mA Speed: 2600–3000rpm Duty Cycle: Continuous Capacitor: 2µF Input/Output: 13mm barb Water Resistance: IPX2 Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos. Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe. Warning:  Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged. Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use.   35L (110V) 35L (220V) 65L (220V) 100L (220V) 10 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 25 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 50 ft. 12 Gauge 12 Gauge 10 Gauge 8 Gauge     FermZilla Tri-Conical Fermenter The Gen 3.2 FermZilla Tri-Conical features a newly designed collection container with top & bottom PCO1881 ports. The collection container has a 3" T.C. opening and installs on the Conical with a 3" T.C. butterfly valve. The molded 3" T.C. ferrule on the tank is a huge improvement over the Gen 2 model—eliminating the complicated dump valve design and simplifying the collection container connection. Brew with confidence on the new Tri-Clover FermZilla! NOTE: The primary example photo shows the collection container from the Gen 3 FermZilla. Out of the box, the FermZilla Conical is an amazing fermenter that will immediately step up your game on the cold side of the brewing process. But what we love most about this unit is how easily it is to upgrade as you go—adding more functionality and gaining more precise control over your fermentation with each new accessory. Below are some of our favorite add-ons for the FermZilla Tri-Conical Fermenter. Pressure Kit The FermZilla is the perfect option for brewers that want all the advantages of a conical fermenter without the price tag of a full blown stainless steel unit. It allows you to dump trub, harvest yeast, and with the addition of the FermZilla Pressure Kit, you can carbonate and serve – all in one vessel! The clear PET tank allows you to visually monitor fermentation activity and is pressure rated to 2.4 Bar (34.8 psi), which means you can ferment under pressure, reducing ester and fusel alcohols in your finished beer. This also gives the ability to perform pressure transfers. If you prefer to move your finished beer to a keg or other vessel, you can do so with little to no oxygen exposure. Tri-Clamp Pressure Lid Add a 2" T.C. port to your fermenter by replacing the standard lid with the FermZilla Tri-Clamp Pressure Lid. This will give you an opening to add dry hops or other additions without needing to remove the entire lid, or you can upgrade down the road with a Hop Bong sight glass in order to add CO2 and purge your hop charge of oxygen. PCO1881 threaded ports are still there for Ball Lock Caps, as well as undrilled ports for an optional Thermowell and Temp Twister cooling coil. Hop Bong Pressure Pack The ultimate upgrade kit! The Hop Bong Pressure Pack has all of the parts included with the Pressure Kit and Tri-Clamp Pressure Lid but fully parted out to remove the guess work. If the Tri-Conical is your first FermZilla fermenter, this accessory kit is for you. Load up the Hop Bong, flush it with CO2, purge out oxygen with the handy PRV on top, then simply open the Butterfly Valve to inject your beer with a 6 oz payload of dry hops. FermZilla Gen 3 vs Gen 3.2: 3" x 3" T.C. butterfly dump valve 3" T.C. compatible collection container 600 mL collection container w/ top & bottom PCO1881 threaded ports What's Included: FermZilla 27L Tank with 3" T.C. Bottom Port 3" T.C. Butterfly Valve 600 mL Collection Container with 3" T.C. Connection Stainless Steel Stand with Swing Handles Stainless Steel Handle Assembly Top Lid with PRV (35 psi) 3" tri-clamp with gaskets 3-Piece Airlock Graduation Sticker Adhesive Thermometer Spare Seals Specs: 27 L (7.1 gal) Total Volume Pressure Rated to 2.4 Bar (34.8 psi) Height in Stand - 29.5" Height w/ Airlock - 33.7" Tank Diameter - 13.9" Diameter in Stand - 15.3" Lid & Collection Container Ports - 28 mm PCO 1881 threads Temperature Rating: When not under pressure, do not expose to liquids above 131°F When under pressure, do not expose to any temperatures above 95°F* Installation Note: For best performance with your Floating Dip Tube, ensure there is not an excess amount of slack when the silicone dip tube is installed and shorten it if needed. With the floating dip tube installed on your empty FermZilla, you ideally want the dip tube to hang freely with just enough length for the end of the dup tube to touch the bottom of the tank.

Read more less

Replacement RAPT Controller for 65L Gen 4 BrewZillas. Compatible with all Gen 4 models. This will not work with BrewZilla Gen 3.1.1 models or older. It is also not suitable for DigiBoil units. Please refer to the instruction manual on adjusting the controller between the Gen 4 units. There is a mechanical toggle switch on the back of the board that will need to be adjusted. KegLand Part Number: KL20305  

Read more less

Pronounced aromatic characteristics that add a wonderful flavor to beer styles like IPAs and Pale Ales With a high AA%, this hop can also be used as an early boil addition for bittering Type 90 Hop Pellets Ekuanot® was originally released in 2014 and has surged in popularity and growing acreage. The ridiculously high oil content (2.5-4 ml/100g!) and desirable aromatics have lead breweries of all sizes to flock to this hop. Great for all beer styles but definitely featured in IPAs and other hop forward beers. Ekuanot® is described as having aromas of melon, berry, orange peel, lime, papaya, pine and fresh peppers.  Try it in your next batch and see what flavors you find! YCH Lot# P91-HUEKU7171 — Option 7171 Lot Analysis Chart This lot was noted to display intense stone fruit, citrus and tropical character up front, with floral, melon, and pomme notes in the background Alpha Acids - 14.5% Total Oil (mL/100g) - 2.8 Sourced from C&C Hop Farms and Carpenter Ranches Hop Statistics: Alpha Acids: 14.5% Beta Acids: 4.7% Total Oil (mL/100g): 2.8 B-Pinene: 0.4% Myrcene: 25% Linalool: 0.3% Caryophyllene: 12.7% Fernesene: 0.5% Humulene: 22.6% Geraniol: 0.7%  

Read more less

Already own a Tapcooler, and want a better and more efficient way to fill your bottles with it? Then look no further than the Magnetic Handsfree Mount for the Tapcooler. This accessory allows you to mount your Tapcooler to the side of any magnetic surface (like your kegerator or keezer) to enable handsfree filling, bottle after bottle. No more having to hold onto the Tapcooler while filling. With this, you can setup the bottle, begin filling, and then use your free hands to get ready for the next bottle. Get the handsfree mount for your Tapcooler today, and make filling your homebrew bottles even MORE fun (if that was possible)! NOTE: You'll need to use the Beer Valve Connector, Intertap Extension Tube, or Faucet Extension Tube to use the handsfree mount. These items are all sold separately, so make sure to grab one if you don't have one already. This item is the handsfree mount only. The Tapcooler bottle filler and extension tubes are all sold separately.

Read more less

Replacement reservoir for 1.5" tri-clamp spunding valve. Compatible with both 1 BAR BrewBuilt model (CON4P36) and 2 BAR MB model (CON4P35-MB).

Read more less

For use with the 35L BrewZilla Boiler Extension Kit. It does not come with an extra Wire Malt Pipe Support Ring. If you're using the extended malt pipe with the 35L DigiBoil, you will need to purchase the ring separately. If you're using the malt pipe with the 35L BrewZilla you can either move your ring up to the boiler extension, or buy an additional ring so you can remove the malt pipe in two steps. You will also need the Ricirculation Arm Extension to continue using the BrewZilla's recirculation arm. Compatible with Gen 3 / Gen 4 BrewZillas. KegLand Part Number: KL26468

Read more less

For use with the 65L BrewZilla Boiler Extension Kit. It does not come with an extra Wire Malt Pipe Support Ring. If you're using the extended malt pipe with the 65L DigiBoil, you will need to purchase the ring separately. If you're using the malt pipe with the 65L BrewZilla you can either move your ring up to the boiler extension, or buy an additional ring so you can remove the malt pipe in two steps. You will also need the Ricirculation Arm Extension to continue using the BrewZilla's recirculation arm. Compatible with 65L Gen 3 / Gen 4 BrewZillas. Example image of the 35L model shown here. KegLand Part Number: KL32834

Read more less

Replacment malt pipe for the 35L BrewZilla Gen 4. This unit is not suitable for older generation BrewZillas or DigiBoils. KegLand Part Number: KL32773   Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos.

Read more less

Replacment malt pipe for the 65L BrewZilla Gen 4. This unit is not suitable for older generation BrewZillas or DigiBoils. KegLand Part Number: KL32797   Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos.

Read more less

The Gen 4 BrewZilla represents one of the greatest upgrades in technology and features that we've ever seen in a new generation of BrewZilla all-in-one brewing system. WiFi/Bluetooth Enabled RAPT Controller The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen. But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability. And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer! But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings. Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road. High Capacity Malt Pipe With an approximately 23.5 lb capacity, the BrewZilla can mash nearly 50% more grain than similar sized models of the Anvil Foundry and Grainfather G30. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery’s grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency. Concave Base with Center Draining Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind. Ultra Low Watt Density Elements The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy. Easy Access Built-In Pump The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet. If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer. Perfect for Distillation If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find. Features: Gen 4.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons WiFi/Bluetooth Enabled RAPT digital temperature controller Automatic step mashing with 6 programmable stages 220-240V power NEMA 6-30P plug Requires NEMA 6-30R receptacle Requires 11 amps from 30 amp circuit Dual heating elements (1900 watts and 500 watts) Stainless steel 1/2" ball valve for gravity draining or transferring via pump Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Adjustable lid clamps (do not use with glass lid in place - see below) Magnetic drive pump for recirculation, transfers, and cleaning Recirculation arm PPSU sight glass Bottom handle for easy lifting and pouring Rubber feet Temperature reads in °F or °C Approximately 32.75" H (with recirculation arm) x 12.5" D Recommended max. grain bill: 23.5 lbs AlcoEngine Still ready with the purchase of a Distillation Lid Pump Specs: Max Capacity: 2.9–3.1 gal/min Max Head: 4.9–6.8 ft. Poles: 2 Voltage: 220–240V-AC Frequency: 50–60Hz Power: 6 watts Current: 60 mA Speed: 2600–3000rpm Duty Cycle: Continuous Capacitor: 2µF Input/Output: 13mm barb Water Resistance: IPX2 You Will Need: 2' of H985 1/2" ID Silicone tubing for sparging and draining. To connect included Chiller: (20') of D1710 1/2" ID beverage tubing (or whatever length required, (3) H950 hose clamps and (1) brass hose by thread adaptor (H508). These items come in the Wort Chiller Connection Kit, add the kit to your cart and use code ZILLAKIT at checkout. KegLand Part Number: KL27434 Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos. Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe. Warning:  Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged. Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use.   35L (110V) 35L (220V) 65L (220V) 100L (220V) 10 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 25 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 50 ft. 12 Gauge 12 Gauge 10 Gauge 8 Gauge  

Read more less

Perfect for new world pale ales, IPAs, hoppy lagers, and any beer you want a bold fruity hop character to shine Aroma Profile: Grapefruit, Passion Fruit, Tropical Alpha Acids: 11.5 – 14.5% Cryo Hop® Hop Pellets Higher AA and nearly twice the resin content of traditional T-90 hop pellets Increase yield by reducing vegetal matter in your brewhouse and fermenter Cryo Hops® provide brewers with the ability to get gigantic hop character while reducing astringent and unpleasant vegetal flavors. With a substantially higher oil and resin content, LupuLN2 powder offers up all the flavor and aroma of a heavily hopped beer, but with a significanly reduced grassy character. Additionally, the lower dosage rate of the concentrated powder reduces the volume of trub and therefore, kettle loss. Using Cryo Hops® you will net more beer that is clearer! Typical usage of Cryo Hops® would be roughly 50% of pellets. LupuLN2 powder can be used in any application where traditional hop products are utilized, including: Bittering, Kettle, Whirlpool and even direct to the fermentor.  It is suggested that you use Cryo Hops® as late additions, in the whirlpool or dry hop, as the volatile aromatic compounds will be driven off if added early in the boil. Cryo Hops® are an innovative hop product that is made by separating the lupulin from the hop flower using cryogenic processing. The result is a product with twice the potency of T90 pellets, with reduced astringency and vegetative material. Note: These hops come pelletized. The powder is compressed into pellet form to make handling easier. Typical Hop Statistics: Alpha Acids: 11.5 – 14.5% Beta Acids: 10.0 – 13.0% Total Oil: 2.0 – 4.0%   Riwaka™  is a  trademark owned by New Zealand Hops Limited Company Cryo Hops® is a registered trademark owned by Yakima Chief Hops.

Read more less

Ideal for modern American pale ales, IPAs, West Coast Pilsners, and Hazys Aroma Profile: Citrus, Tropical, White Wine Alpha Acids: 23.0 – 27.0% Cryo Hops® Hop Pellets Higher AA and nearly twice the resin content of traditional T-90 hop pellets Increase yield by reducing vegetal matter in your brewhouse and fermenter Cryo Hops® provide brewers with the ability to get gigantic hop character while reducing astringent and unpleasant vegetal flavors. With a substantially higher oil and resin content, LupuLN2 powder offers up all the flavor and aroma of a heavily hopped beer, but with a significanly reduced grassy character. Additionally, the lower dosage rate of the concentrated powder reduces the volume of trub and therefore, kettle loss. Using Cryo Hops® you will net more beer that is clearer! Typical usage of Cryo Hops® would be roughly 50% of pellets. LupuLN2 powder can be used in any application where traditional hop products are utilized, including: Bittering, Kettle, Whirlpool and even direct to the fermentor.  It is suggested that you use Cryo Hops® as late additions, in the whirlpool or dry hop, as the volatile aromatic compounds will be driven off if added early in the boil. Cryo Hops® are an innovative hop product that is made by separating the lupulin from the hop flower using cryogenic processing. The result is a product with twice the potency of T90 pellets, with reduced astringency and vegetative material. Note: These hops come pelletized. The powder is compressed into pellet form to make handling easier. Typical Hop Statistics: Alpha Acids: 23.0 – 27.0% Beta Acids: 12.0 – 16.0% Total Oil: 2.0 – 5.0%   Nelson Sauvin™ is a registered trademark owned by New Zealand Hops. Cryo Hops® is a registered trademark owned by Yakima Chief Hops, LLC.

Read more less

This Duotight elbow is mainly used where a stronger connection is required on a rigid port. One side is a standard 8 mm Duotight connection and the other side is a compression adapted Duotight Screw Lock connection for 6.35 mm (1/4") rigid fittings.  This Duotight elbow fitting is compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines! Features: Insert tubing and firmly push to connect Easily release tubing by pushing in the collet Suitable for both gas & beverage applications Made from food-grade acetal plastic Double O-rings made from highly chemical resistant EPDM Locking teeth made from stainless steel Pressure rated to 150 psi Temperature rated to 212°F (100°C) Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals. KegLand Part number: KL24624  

Read more less

PLEASE NOTE: The supplier of this product has temporarily halted shipments to addresses within the state of California. If you are a CA resident, please note your order will not be fulfilled and will ultimately be canceled. We hope to have this issue resolved with the supplier as soon as possible.   Thanks to the 70L (18.5 gal) capacity, homebrewers can produce more beer to share or commercial breweries now have a unit that's small enough for pilot testing. It also has a smart controller with built-in wireless connectivity and mobile app integration for step-by-step remote-controlled brewing. The G70² gives you everything you need in one compact package that can be used virtually anywhere. Please Note - this system comes standard with a NEMA 6-15P plug, and requires access to a 220v-240v power supply. New Features on the G70²: The G70² features a perforated grain basket and the sight glass is now integrated into the recirculation pipework. The new basket design provides an improved brewing experience with no top plate or additional pipework required, making for an even more efficient mash and an easier clean. Perforated grain basket for an improved brewing experience with no top plate or additional pipework required. Integrated sight glass is now a part of the recirculation pipework for easy volume reading. 70L of innovation, consistency and power have helped to create one of our most compelling systems to date. The inherent strength and safety capabilities of the G70² are matched by its bold, contemporary look and new smart brewing technologies. From the creators of the original award-winning all-grain brewing system, the Grainfather G70² represents the next level in brewing equipment. We’ve stepped up our game to bring you a smarter brewing system with a larger 18.5 gal capacity, improved design, wireless control, app integration and the same Grainfather signature quality guarantee. Whether you're a homebrewer looking to raise the stakes or a commercial brewery looking to bring authenticity back to your pilot batches, the G70² is your true brewing companion. It gives you everything you need in one compact package that can be used virtually anywhere. Features: Two-stage false bottom. The conical base allows a false bottom with an inner collar to sit in the recess of the base. Early testers used 21 oz of hops and saw full flow through the pump. This is very effective. Bespoke 3.2 kWh concealed conical heating element. Make the most of the power available. The element covers around 80% of the base and is mounted using a thermal paste rather than braised. This moves the heat efficiently upwards, minimizing the loss of heat to areas where it’s not needed. As it’s spread in a wide area, hot spots and scorching are very unlikely. Also, most solids settle on the false bottom, so they won’t touch the elements. As it’s concealed, it makes cleaning easy too. Integrated sight glass for easy volume readings during sparging. Instead of trying to judge the level of your preboil, you can easily sparge until you reach preboil volume. It’s also easy to clean after every brew. The sight glass cap can be replaced with the sight glass cleaning barb to easily recirculate a cleaning solution. Bottom drain below the false bottom means minimal dead space. High temperature, high flow rate, food-grade pump. With an 2.1 gal per minute flow rate, you can transfer your brew efficiently and safely. Heavy duty handles on the outside of the G70² unit. Convenient side entry recirculation. Rather than up and over, the G70² has a built in port on the side of the unit. If the pump is accidentally switched on, the wort will be safely directed back into the boiler. New rolled edge, mash plates and hop filter for increased strength and easy set up. There’s no more silicone seals, as the plates now have a smooth finish, making them more robust, hard-wearing and easy to install. Compared to the G30, the G70² is wider but not that much taller. Comparatively, the draining is still quick from the basket and there’s less likelihood of stuck sparges as the draining surface area is bigger. Safety aspects including locked in support ring, heavy duty, no slip brackets on the grain basket and protection from knocking the ball valve open. Automatic heat sensors and safety cut-out for dry boil protection. Color LCD controller screen with magnetic mounting for easy viewing from all angles and manual control. Glass lid with handle. Ball valve for sampling/draining. This runs in line with the pump so it’s particularly helpful when draining the cleaning water. The water runs out quickly, emptying the unit in no time. Huge Wort Chiller included. Despite the volume being more than double, cooling times remain around the same as the G30 thanks to a more powerful pump, efficient false bottom and bigger wort chiller to match the wider unit. The large size means it needs to be positioned away from the G70², however this is made easy with longer silicone tubing attached as standard. Lifting bar included with winch lifting hook. Use the bar for a two person lift or with a stable winch system for individual brewers to lift the grain basket. Large dual-stage hop filter provides a large surface area to allow for a hopping rate of up to 3.3 lbs, which also reduces pump load and blockages. Robust stainless steel body and excellent build quality. Specifications: 304 Grade stainless steel body 220 - 240V 18 Gal Capacity Max Grain Bill: 35 lbs Min Grain Bill: 18 lbs Powerful high flow pump: 15W

Read more less

This Belgian strain, traditionally used for wild yeast fermentations, produces a slightly tart beer with delicate mango and pineapple characteristics. This wild yeast has grown in popularity for styles like American IPA, American pale and blonde ales due to its tropical and stone fruit flavors and aromas. This Saccharomyces strain can be used like other house strains and can be easily cleaned with proper CIP procedures. PurePitch® Next Generation—now with more yeast, get a foolproof fermentation without a starter! Just twist the cap & pitch! Everything you missed about the vial with the innovation of PurePitch®. Attenuation: 70-85% Flocculation: Low Alcohol Tolerance: 10-15% ABV Optimum Fermentation Temp: 70-85°F Cell Count: 150 Billion For best results we always recommend ordering an ice pack with your liquid yeast. Please Note: When choosing an ice pack option beware that the liquid yeast will not arrive cold even when shipped together. Ice packs and insulated mailing options are designed to keep the yeast colder for longer during shipment, but they will not ensure that your yeast arrives cold. We will not replace liquid yeast that arrives warm. During warmer months we strongly recommend you choose dry yeast.

Read more less

Introducing the Ss Glycol Chiller 3/8 HP, which will maintain lager temps and enable crash cooling for up to 6 vessels even in relatively high ambient temperatures. We designed the chiller to integrate seamlessly with our FTSs kits to provide a complete temperature control system. Since each FTSs kit includes its own dedicated temperature controller, pump, and tubing, each vessel can be connected to the glycol chiller with its own independent loop. The parallel design of this set up offers the ability to ferment at ale temps in one vessel, and maintain precise serve or crash cooling temps in another vessel. The Glycol Chiller can also be paired with our line of Ss Brite Tanks to hold beer at serving temperatures. This system offers both flexibility and expandability for your home brewery.  Features: Pumps not included, attach up to 6 FTSs Touch kits (sold separately) Capable of crash cooling and lagering Assuming one vessel is crash cooled at a time: Chills Up to 4 - 1 BBL Chronicals, Unitanks or Brite Tanks Chills Up to 6 - 1/2 BBL, 14, or 7 gal Chronicals or Unitanks, 10 or 20 gal Brite Tanks Chills up to 6 - 14 or 7 gal Brew Buckets  Not Compatible with the FTSs Pro Series Controllers Specs: Vertical chassis layout 120 VAC 3/8 HP Compressor 3576 BTUs/Hr 10 Gallon Reservoir with Pressure Vent R290 Refrigerant Casters included Made in France Dimensions: 18" W x 18" D x 28" H  

Read more less

The Ss Glycol Chiller | 1/5 HP, will maintain lager temps and enable crash cooling for up to 3 vessels even in relatively high ambient temperatures. We designed the chiller to integrate seamlessly with our FTSs kits to provide a complete temperature control system. Since each FTSs kit includes its own dedicated temperature controller, pump, and tubing, each vessel can be connected to the glycol chiller with its own independent loop. The parallel design of this setup offers the ability to ferment at ale temps in one vessel, and maintain precise serve or crash cooling temps in another vessel. The Glycol Chiller can also be paired with our line of Ss Brite Tanks to hold beer at serving temperatures. This system offers both flexibility and expandability for your home brewery.  Features:  Pumps not included, attach up to 3 FTSs Touch kits (sold separately) Capable of crash cooling and lagering Assuming one vessel is crash cooled at a time: Chills Up to 2 - 1/2 bbl, 14 gal Chronicals, Unitanks, or Brew Buckets Chills Up to 3 - 7 gal Chronicals, Unitanks, or 10 gal Brite Tanks Chills Up to 3 - 7 or 3.5 gal Brew Buckets Not Compatible with the FTSs Pro Series Controllers Specs: Vertical chassis layout 120 VAC 1/5 HP Compressor 1450 BTUs/Hr 4.75 Gallon Reservoir with Pressure Vent R290 Refrigerant Casters Included Made in France Dimensions: 14" W x 11" D x 27.5" H  

Read more less

An elegant combination of 304 stainless steel and non-slip silicone come together for the coffee industry's most complete commercial-grade cold brew system. What's Included: Cold Brew Bucket Lid Stainless Cold Brew Basket w/ Silicone Handle Silicone Lid Deep Bend Pick-Up Tube 10x - High Strength Filter Bags Specs: Designed for 7 gal vessel volume 5 lb. max coffee grounds 3.5 gal max coffee concentrate output Designed to pair with our iconic series of 7 gal | Brew Buckets. The system will also work with the 7 gal | Chronical series.

Read more less

The Essential Kits are designed to get you up and brewing with one click.  It's highly recommended you add this to your cart with the purchase of a Brew Bucket Series. Hose Barb | ½” 90° for Blow-Off Tubing | ½” ID Silicone (2ft) Tubing | ⅜” ID Silicone (5ft) Hose Clamps (2)

Read more less