Freight Only

Cooling & heating in one premium quality unit Control fermentation temperatures, cold-stabilize insulated tanks, or heat tanks during cold weather Fill from the exterior without the need to remove covers or panels Program and monitor temperatures via the digital controller Non-Return Kit installed as standard to prevent backflow when positioned below your tank jacket, heat exchanger, or piping system Four locking casters offer ease-of-mobility when moving the unit around the winery 1.8 Ton / 21,840 Btu cooling capacity 208V, 3 Phase power Made in Germany by Kreyer Cooling and Heating in one unit! Every Winemaker can appreciate the benefits of precise temperature control during all stages of production. This mobile unit allows you to easily control your ferment temperatures, heat your tanks during winter to expedite Malo-Lactic fermentation, or cold-stabilize your white wines. This unit can be used as portable unit in a larger winery or as a fixed system supplying a glycol loop in a smaller winery. Unit is used for heating or cooling but cannot supply both at the same time. Manufactured by Kreyer, the World's leading producers of wine-cooling equipment. Uses: Cooling of must for cold soaks, slow starting ferments Heating up must after a cold soak period Cold Stabilization of tartaric crystals Controlling fermenting temperatures through cooling or heating Maintaining storage temperatures in tanks/barrels Check out these features: Cools or Heats 1.8 Tons (21,840btu) of cooling power .85 Tons of heating power Can cool glycol/water bath down to -10C/14F or up to 42C/107F 208V 60Hz 3 phase supply voltage drawing 13.1 amps Rolls on four locking casters Sheet metal housing, electrolytic galvanized high surface quality, powder-coated and abrasion-resistant casing 7 Gallon Insulated Plastic glycol/water reservoir Easy to fill from outside Evaporator coil made of stainless steel High-quality Grundfos recirculation pump Built in pressure switch shuts down recirculation pump when not needed Digital Thermostat Lifting/Crane Hooks for transport All panels remove for easy access All units pass multiple tests prior to shipment German Engineering Controlled by compact PC boards with a temperature accuracy up to 0.1 degree Celsius. 33"L x 25"W x 31.5"T Unit has 1" Male BSP w/ 3/4" Female BSP inlet / outlet 6 Month Electrical Warranty 1 Year Mechanical Warranty CE Certified Please Note:  This unit REQUIRES 208 v Three Phase power and will not function on anything else.   Please confirm that you have the proper power for this unit before purchasing, and plan to have a qualified electrician wire the necessary plug to the cord. Available in larger sizes.  For additional product options click here.

Read more less

Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory.   Looking for a premium kegerator to install under the counter of your home bar or outdoor kitche? The KOMOS Outdoor Kegerator offers the best value in the USA for an all stainless steel outdoor rated kegerator. With an all stainless interior and exterior, this unit is built to operate at a level other kegerators simply can't reach. Heavy duty casters come standard for maximum mobility, and front facing ventilation makes it ideal for using as a built in kegerator in an outdoor kitchen. Features include tower cooling fan, wide-range digital controller, stainless door and exterior, stainless floor and interior, heavy-duty casters as standard, and a list of options. Please note the kegerator does not come with a plug for the tower hole. The KOMOS Outdoor Kegerator is intended to be installed under counter tops or paired with a standard 3" diameter draft tower. If you plan to install the kegerator under a countertop, the top cover will need to be removed and you will need to install the Build-In Door Hinge, as the top door hinge is removed with the cover. For homebrewers looking for a fermentation chamber, we recommend the KOMOS residential model. Feature Summary: Digital Thermostat with wide 28 - 76° F temp range. CO2 Tank strap mounts above a triangular stage inside the kegerator Tower cooling fan Efficient and powerful compressor uses R600 refrigerant Beautiful stainless interior and exterior Stainless Steel Countertop Style Drip Tray Stainless Steel Floor for additional keg support Heavy duty rolling casters come standard Front-facing ventilation allows it to be built-in to a cabinet, kitchen, or outdoor counter  Lock & key to keep your precious beverages protected UL & CSA Certified Detailed instructions on assembly and use Specifications: 24" Wide 25" Deep 35" Tall (fridge only) 39.25" Tall with Caster Wheels 115V - 60 hz 1.6 Amp draw Works well in ambient temperatures up to 100°F Internal Dimensions: 21" Wide 18.25" Max Depth 28.5" Tall 27" clearance under controller What Fits: 2.6 Gal. BrewKeg - 2 5 Gal. Torpedo Keg - 3 5 Gal. Slimline Torpedo Keg - 3 5 Gal. Megamouth Torpedo Keg - 2 5 Gal. Pin Lock Cornelius Keg (Corny Keg) - 3 5 Gal. Ball Lock Cornelius Keg (Corny Keg) - 3 5.16 Gal. Sixth Barrel Keg (Sixtel, Log) - 3 7.75 Gal. Quarter Barrel Keg (Pony Keg, Stubby Quarter) - 1 7.75 Gal. Slim Quarter Keg (Tall Quarter, The Slim) - 2 15.5 Gal. Half Barrel Keg (Full Size Keg) - 1 See below for the Kegerator Instruction Manual.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. This preconfigured tank comes with: Max jacket with NPT connections Liquid level indicator with a liter scale Welded gland NW10 for sampling Welded gland for thermometer NW10 with cap Venting welded gland with a 2 in. TC connection Racking outlet with a 2 in TC connection Bottom outlet with a 2 in. TC connection Dome with hinged and swiveling venting nozzle Mash door - 12.2 in. (310 mm) x 16.5 in. (420 mm) Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters   Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel's RO-Z style grant/mixing tank is an extremely handy tool in any winery. The open top, 45° mixing port, and total drain outlet make mixing additions into larger tanks a snap - insert your mixer in the 45° port and position the mixing tank under the racking port of your larger tank. Run wine into the mixing tank with the mixer running, pour in your tartaric acid, sugar, bentonite, etc.; and pump out of the drain port to return the wine to the tank. Key Features Heavy duty nylon casters make the tank easy to move around the winery Two fixed casters and two swivelling casters with brakes 45° mixing port is reinforced and strong enough to support a mixer without an additional stand Variable Volume tank lid available (sold separately) Sack support rack available (sold separately) Click Here for more information on the key features of all Speidel Tanks.

Read more less

Variable speed loading and sorting table with hopper sized to accept grapes from a macro bin Long enough for one to two people to remove leaves and bad bunches as the grapes feed from the hopper to your crusher destemmer Rolling casters for easy mobility Made in Italy by EnoItalia This Sorting Table solves several issues. It provides a lower receiving hopper (not shown in picture) in which to load fruit. The bin is oversized to allow you to gradually empty a macrobin when using a hydraulic bin tilter. There is enough space for two people to remove leaves, bad bunches, as the grapes are fed into the Crusher. Because the table consistently feeds the Destemmer/Crusher it also solves one of the key problems of overloading. When you dump large quantities of grapes into a crusher all at one time the machine will overload and not work as well, or even fail. The Sorting Table features speed control which is essential for different grape styles, level of sorting, and processing quality. Features: Variable speed 1 phase 220 V required 23.6 in Wide (60 cm) 181.1 in Total Length (460 cm) 141.7 in Sorting Length (360 cm) 2hp/1.5 kw power

Read more less

Cooling & heating in one premium quality unit Control fermentation temperatures, cold-stabilize insulated tanks, or heat tanks during cold weather Fill from the exterior without the need to remove covers or panels Program and monitor temperatures via the digital controller Non-Return Kit installed as standard to prevent backflow when positioned below your tank jacket, heat exchanger, or piping system Four locking casters offer ease-of-mobility when moving the unit around the winery 3 Ton / 36,000 Btu cooling capacity 230V, 3 Phase power Made in Germany by Kreyer Cooling and Heating in one unit! Every Winemaker can appreciate the benefits of precise temperature control during all stages of production. This mobile unit allows you to easily control your ferment temperatures, heat your tanks during winter to expedite Malo-Lactic fermentation, or cold-stabilize your white wines. This unit can be used as portable unit in a larger winery or as a fixed system supplying a glycol loop in a smaller winery. Unit is used for heating or cooling but cannot supply both at the same time. Manufactured by Kreyer, the World's leading producers of wine-cooling equipment. Note: This unit runs off 230V 3 phase power. It will not run off 208V. Uses: Cooling of must for cold soaks, slow starting ferments Heating up must after a cold soak period Cold Stabilization of tartaric crystals Controlling fermenting temperatures through cooling or heating Maintaining storage temperatures in tanks/barrels Check out these features: Cools or Heats 3 Tons (36,000btu) of cooling power (larger Chilly Max's are available) .85 Tons of heating power Can cool glycol/water bath down to -10C/14F or up to 42C/107F 230v 60Hz 3 phase supply voltage drawing 19.3 amps Rolls on four locking casters Sheet metal housing, electrolytic galvanized high surface quality, powder-coated and abrasion-resistant casing 7 Gallon Insulated Plastic glycol/water reservoir Easy to fill from outside Evaporator coil made of stainless steel High-quality Grundfos recirculation pump Built in pressure switch shuts down recirculation pump when not needed Digital Thermostat Lifting/Crane Hooks for transport All panels remove for easy access All units pass multiple tests prior to shipment German Engineering Controlled by compact PC boards with a temperature accuracy up to 0.1 degree Celsius. 33"L x 25"W x 31.5"T Unit has 1" Male BSP w/ 3/4" Female BSP inlet / outlet 6 Month Electrical Warranty 1 Year Mechanical Warranty CE Certified Please Note:  This unit REQUIRES 230 v Three Phase power and will not function on anything else.   Please confirm that you have the proper power for this unit before purchasing, and plan to have a qualified electrician wire the necessary plug to the cord. Available in larger sizes.  For additional product options click here.

Read more less

Cooling & heating in one premium quality unit Control fermentation temperatures, cold-stabilize insulated tanks, or heat tanks during cold weather Fill from the exterior without the need to remove covers or panels Program and monitor temperatures via the digital controller Non-Return Kit installed as standard to prevent backflow when positioned below your tank jacket, heat exchanger, or piping system Four locking casters offer ease-of-mobility when moving the unit around the winery 1.8 Ton / 21,840 Btu cooling capacity 230V, Single Phase power Made in Germany by Kreyer Cooling and Heating in one unit! Every Winemaker can appreciate the benefits of precise temperature control during all stages of production. This mobile unit allows you to easily control your ferment temperatures, heat your tanks during winter to expedite Malo-Lactic fermentation, or cold-stabilize your white wines. This unit can be used as portable unit in a larger winery or as a fixed system supplying a glycol loop in a smaller winery. Unit is used for heating or cooling but cannot supply both at the same time. Manufactured by Kreyer, the World's leading producers of wine-cooling equipment. Note: This unit runs off 230V single phase power. It will not run off 208V. Uses: Cooling of must for cold soaks, slow starting ferments Heating up must after a cold soak period Cold Stabilization of tartaric crystals Controlling fermenting temperatures through cooling or heating Maintaining storage temperatures in tanks/barrels Check out these features: Cools or Heats 1.8 Tons (21,840btu) of cooling power .85 Tons of heating power Can cool glycol/water bath down to -10C/14F or up to 42C/107F 230V 60Hz Single phase Power supply Required Rolls on four locking casters Sheet metal housing, electrolytic galvanized high surface quality, powder-coated and abrasion-resistant casing 7 Gallon Insulated Plastic glycol/water reservoir Easy to fill from outside Evaporator coil made of stainless steel High-quality Grundfos recirculation pump Built in pressure switch shuts down recirculation pump when not needed Digital Thermostat Lifting/Crane Hooks for transport All panels remove for easy access All units pass multiple tests prior to shipment German Engineering Controlled by compact PC boards with a temperature accuracy up to 0.1 degree Celsius. 33"L x 25"W x 31.5"T Unit has 1" Male BSP w/ 3/4" Female BSP inlet / outlet 6 Month Electrical Warranty 1 Year Mechanical Warranty CE Certified Please Note:  This unit REQUIRES 230 v Single Phase power and will not function on anything else.   Please confirm that you have the proper power for this unit before purchasing, and plan to have a qualified electrician wire the necessary plug to the cord. Available in larger sizes.  For additional product options click here.

Read more less

Premium quality laser-welded stainless steel sealed tank wine, beer, spirits, cider, kombucha, and other beverages Cooling jacket covers the entire tank of efficient glycol cooling Top hatch provides a large, convenient opening for adding oak or other additions Conical-shaped complete drainage bottom for maximum product yield and easy cleaning Tri-clamp ferrule ports with thermometer and thermowell combo included Made in Germany by Speidel We are proud to present our line of premium quality stainless steel tanks. Built in Germany by Speidel, the world-class traditions of German engineering and craftsmanship are reflected in these tanks. And, after examining tanks built by every major manufacturer worldwide, we can safely say that when it comes to features, quality and price, these tanks represent the very best value available in stainless steel beverage storage. We've found that these tanks work well for beer, wine, spirits, cider, and more! Convenient top hatch makes cleaning and oaking easy. Heavy duty sealing mechanism and thick gasket ensure an air tight seal. The tanks will support a few p.s.i. of pressure, however they are not pressure rated or designed to be used under pressure. The inside is finished to Speidel quality standards. Bottom drain fittings are 1.5" Tri-Clamp. Flat bottom tanks do not have legs; conical tanks come standard with legs. Speidel Quality Features: Full Jacket - Equipped with a jacket that covers all accessible areas of the tank and is designed for an operating pressure of 2.5 to 6 bar. This will allow you to hook it into a glycol system (see our Kreyer Chilly45, GLY410) for complete temperature control!   Interior Finish - Speidel tanks feature an ultra-smooth 2R rated interior surface which effectively resists the build-up of tartrate residues. Clean your tanks with cold water after cold stabilization! Say goodbye to harsh cleaning chemicals and expensive CIP systems!   Weld Quality - Speidel's robotic-arm laser welders create flawless stainless to stainless junctions that look and feel more like a taped fabric seam than a traditional weld. Ultra high-quality welds leave no chance for residual product to harbor spoilage organisms.   Thickness - Speidel tanks are designed to be the correct thickness for the tank's total volume.   Complete Drainage Bottoms - All Speidel tanks are outfitted with conical, pocketed bottoms for total drainage, which maximizes product yield at rackings and makes cleaning a snap. *Please note that smaller, flat-bottomed tanks do not feature total drainage bottoms.   Tri-Clamp Valve Ferrules - All Speidel tanks come configured for use with Tri-Clamp (TC) style valves and fittings. Tanks up to 1600L capacity are outfitted for use with 1.5 in TC. Other sizes and custom configurations are available at additional cost upon request. **Please Note: TC valves not included. Please inquire with your sales associate for pricing on TC valves and fittings.   Rubber Lid Gaskets - Rubber gaskets are much thicker than the traditional clear vinyl gaskets, which along with their extruded manufacturing process provide a much better seal with the tanks wall. They're seamless and more oxygen resistant than the clear gaskets. That means better protection for your wines!   Warranty - Speidel-Behaelter, GMBH backs up each and every tank with an industry-leading 25 year warranty against defects in materials or workmanship. And, as a 5th generation manufacturer, you can be confident they'll be around to honor that warranty should the need arise. Tank Features: Volume: Sealed, 4400 L.  Open top, 4459 L Manway Lower Jacket: 3.2 m² (4x 1" MPT connections) Upper Jacket: 5.4 m² (2x 1" MPT connections) Complete Drainage Dish Bottom Reinforced Racking valve 2" TC connections Thermometer and Thermowell Combo included Sample Valve included Tank Dimensions: 1400mm D x 3465mm H (55.1" D x 136.4" H)

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. This preconfigured tank comes with: Double jacket with 2xG1" external connections Liquid level indicator with a liter scale Welded gland NW10 for sampling Welded gland for thermometer NW10 with cap Venting welded gland with a 2 in. TC connection Racking outlet with a 2 in TC connection Bottom outlet with a 2 in. TC connection Dome with a hinged and swiveling venting gland Mash door - 12.2 in. (310 mm) x 16.5 in. (420 mm) Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters   Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. This preconfigured tank comes with: Double jacket with 2xG1" external connections Liquid level indicator with a liter scale Welded gland NW10 for sampling Welded gland for thermometer NW10 with cap Venting welded gland with a 2 in. TC connection Racking outlet with a 2 in TC connection Bottom outlet with a 2 in. TC connection Dome with a hinged and swiveling venting gland Mash door - 12.2 in. (310 mm) x 16.5 in. (420 mm) Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters   Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. This preconfigured tank comes with: Double jacket with 2xG1" external connections Liquid level indicator with a liter scale Welded gland NW10 for sampling Welded gland for thermometer NW10 with cap Venting welded gland with a 2 in. TC connection Racking outlet with a 2 in TC connection Bottom outlet with a 2 in. TC connection Dome with a hinged and swiveling venting gland Mash door - 12.2 in. (310 mm) x 16.5 in. (420 mm) Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters   Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. This preconfigured tank comes with: Double jacket with 2xG1" external connections Liquid level indicator with a liter scale Welded gland NW10 for sampling Welded gland for thermometer NW10 with cap Venting welded gland with a 2 in. TC connection Racking outlet with a 2 in TC connection Bottom outlet with a 2 in. TC connection Dome with a hinged and swiveling venting gland Mash door - 12.2 in. (310 mm) x 16.5 in. (420 mm) Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters   Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. This preconfigured tank comes with: Double jacket with 2xG1" external connections Liquid level indicator with a liter scale Welded gland NW10 for sampling Welded gland for thermometer NW10 with cap Venting welded gland with a 2 in. TC connection Racking outlet with a 2 in TC connection Bottom outlet with a 2 in. TC connection Dome with a hinged and swiveling venting gland Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters   Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. This preconfigured tank comes with: Double jacket with 2xG1" external connections Liquid level indicator with a liter scale Welded gland NW10 for sampling Welded gland for thermometer NW10 with cap Venting welded gland with a 2 in. TC connection Racking outlet with a 2 in TC connection Bottom outlet with a 2 in. TC connection Dome with a hinged and swiveling venting gland Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters   Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. This preconfigured tank comes with: Double jacket with 2xG1" external connections Liquid level indicator with a liter scale Welded gland NW10 for sampling Welded gland for thermometer NW10 with cap Venting welded gland with a 2 in. TC connection Racking outlet with a 2 in TC connection Bottom outlet with a 2 in. TC connection Dome with a hinged and swiveling venting gland Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters   Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. This preconfigured tank comes with: Double jacket with 2xG1" external connections Liquid level indicator with a liter scale Welded gland NW10 for sampling Welded gland for thermometer NW10 with cap Venting welded gland with a 2 in. TC connection Racking outlet with a 2 in TC connection Bottom outlet with a 2 in. TC connection Dome with a hinged and swiveling venting gland Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters   Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. This preconfigured tank comes with: Double jacket with 2xG1" external connections Liquid level indicator with a liter scale Welded gland NW10 for sampling Welded gland for thermometer NW10 with cap Venting welded gland with a 2 in. TC connection Racking outlet with a 2 in TC connection Bottom outlet with a 2 in. TC connection Dome with a hinged and swiveling venting gland Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters   Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. This preconfigured tank comes with: Double jacket with 2xG1" external connections Liquid level indicator with a liter scale Welded gland NW10 for sampling Welded gland for thermometer NW10 with cap Venting welded gland with a 2 in. TC connection Racking outlet with a 2 in TC connection Bottom outlet with a 2 in. TC connection Dome with a hinged and swiveling venting gland Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters   Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. This preconfigured tank comes with: Double jacket with 2xG1" external connections Liquid level indicator with a liter scale Welded gland NW10 for sampling Welded gland for thermometer NW10 with cap Venting welded gland with a 2 in. TC connection Racking outlet with a 2 in TC connection Bottom outlet with a 2 in. TC connection Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters   Click Here for more information on the key features of all Speidel Tanks.

Read more less