Wine Filters

This compact filter is designed for the home wine maker who is filtering 5-10 gallons at a time. Perfect for filtering wine concentrate kits. There is a small built in Flojet pump (self-priming, diaphragm pump) that can be used for racking from container to the next by bypassing the filter pads. You will not want to filter wine which contains solids such as stems or oak chips. This will clog the pump and void the warranty. Takes three pads to load this filter. Does not come with filter pads. The intake and outtake tubes are 3/8" and the drip tray tube is 1/4".  

Read more less

This cartridge filter is designed to be installed inline between two ball lock Cornelius kegs. The design uses Argon or Nitrogen gas pressure to push wine out of the full keg, through the filter and into the clean keg. This kit includes a cartridge to filter out particles down to 1 micron in size, which is considered a "fine" or "polish" filtration. This is a fine place to start if your wine is already naturally very clear from successive rackings, or you have pre-fined the wine. If you do not wish to wait for racking to be effective or to pre-fine the wine ahead of filtration, MoreWine! suggests that you start with either our 5 micron or 3 micron cartridge and put the wine through successively finer filter media until you reach your desired level of clarity. The Beer and Wine Filtering Kit comes with one 10" filter housing, a 1 micron 10" spun poly sediment filter, fittings for connection to the filter housing, 3' of beverage line, clamps, and two beverage out ball lock quick disconnects. Spun-polypropylene filters are disposable filters and cannot be effectively cleaned for reuse. However, you can filter multiple kegs with one filter cartridge. Most customers report being able to filter 10-15 gallons of product, however you should be aware that your results will vary depending on the cloudiness of your beer or wine. 5-10 micron is considered rough filtration, 3 micron will remove most yeast, and 1 micron filtration will remove almost all yeast. All filters are rated nominal (will filter out 80-85% of matter at given rating).

Read more less

This tried and true filter pumps fluid from one container, through three filter pads and back into another container. Designed for home winemakers who will be filtering more than 10 gallons at a time. Has a built in Flojet pump, which can be used to rack wine from one container to another by bypassing the filter pads. The pump is relatively small, drawing .5 amps and is standard 110V. Additional features include a carrying handle, built in pressure gauge, on/off switch and 4' power cord. The pressure gauge will tell you when you need to replace the pads. You will not want to filter wine which contains solids such as stems or oak chips. This will clog the pump and void the warranty. Filter package includes 8' of 1/2 ID tubing on the input side and 4' of 1/2" ID tubing on the output side. Input side includes sediment tip but we recommend our 1/2" Racking set up (R310 or R315). The output side comes with a hook for hanging to the side of the carboy. You may also want a racking cane (R373 or R376) on this output side so your receiving vessel fills from the bottom instead of the top (to reduce oxidation.) The manufacturer suggests that you wet the pads before inserting them into the filterhousing. Run a couple of gallons of water through the pads before you start filtering the wine. To help neutralize the pads you can use one to two teaspoons of Citric Acid in 2 gallons of water and run that through the filter. MoreWine suggests that a stock sanitzing solution of potassium metabisulphite and citric acid (1 tblsp each in a gallon of water) ran through the filter followed by a cold water rinse would be the best way to treat your pads prior to use. Please also read the instructions that are included with the filter prior to operation. Facts from the manufacturer: - 8 feet max on the draw hose - 30-35 feet on the push side - Has a 35 PSI limit beyond which it will reduce the flow   Please note the Super Jet Filter does not come with filter pads. The available filter pad options can be found below under "You Might Also Need".  

Read more less

Most breweries and wineries use a large plate filter system to achieve clear product. Now you can do the same at home with two corny kegs. Our Beer and Wine Plate Filter Kit has a larger surface area, which means more yeast and particulate extraction than our cartridge filter, and comes with our plate filter, two disposable filter pads, tubing, flare fittings, and two flare beverage ball locks. Each filtering session requires two pads at a time, and each pad must be the same micron to work. The beer or wine is pushed out of the keg and into the housing at 5 PSI, where it passes on either side of the filter housing, then gets forced from the center through the pads, where it is then pushed out into your clean keg. The rough sides of both filters should be facing each other on the inside of the filter, so the smooth sides face outward. Each filter pad set is good for approximately 5 gallons of beer when the beer has been filtered by the previous size pads or you are starting with the rough filters. These pads are not designed to be back flushed and reused and should be used in one session.

Read more less

Filter your tap water and eliminate that no-win decision of "should I buy expensive bottled water or use the chlorinated water from the tap." This water filter kit features a 10" carbon block filter that removes all chlorine and organic flavor. Kit includes 10" housing, one carbon block filter, garden hose attachment, barbed fittings and 6' of 3/8" vinyl tubing. The carbon block should be replaced after filtering approximately 800 gallons of water or after 1 year of use, whichever comes first. Filter should be disassembled and stored dry when not in use. NOTE: This product should not be used in hot water applications. Cold water only! This product includes a carbon filter and is designed to filter water only (Carbon filters should not be used to filter beer or wine).

Read more less

The Buon Vino 6-Pad Wine Filter offers twice the filtering capacity of the Buon Vino 3-pad wine filter.  One of the major bummers of filtering is when you are all set up and everything is flowing along nicely and then your filter clogs.  You have to stop your operation and change pads.  If you are homewinemaker filtering 60 or more gallons we recommend you step up to the Buon Vino 6 from the Buon Vino 3. Filter package includes 8' of 1/2 ID tubing on the input side and 4' of 1/2" ID tubing on the output side. Input side includes sediment tip but we recommend our 1/2" Racking set up (R310 or R315). The output side comes with a hook for hanging to the side of the carboy. You may also want a racking cane (R373 or R376) on this output side so your receiving vessel fills from the bottom instead of the top (to reduce oxidation.)     Technical Specifications: Delf-priming pump Filtering surface area of 2400 square cm Filtering rate: Approximately 270L per Hour 3 Grades of pads: coarse, polish, and sterilizing Dimensions: 51 cm (length) x 26 cm (width) x 46 cm (height) Weight: 14 kilograms

Read more less

Our Plate Filter has a larger surface area, which means more yeast and particulate extraction. Each filtering session requires two pads at a time, and each pad must be the same micron to work. The product is pushed into the housing at 5 PSI and passes on either side of the filter housing, then gets forced through the pads to the center, where it is pushed out into your awaiting collection vessel, such as a keg or tank. Includes 2 X 24" long hoses (5/16" ID x 7/16" OD) Made from ABS plastic. Temperature rated to 167°F (75°C).

Read more less

Rolling cart wine plate filter Plates made from food-grade Noryl Built-in stainless centrifugal pump Built-in pressure gauge 1.5" tri-clamp inlet/outlet 600L/h wine filtering capacity Made in Italy by Marchisio Small commercial plate filter that will accomodate 20 20cm x 20cm plates. Included 110v 1/2hp, stainless motor will pump wine from your container and push it through the filter and into your aging tank or bottle filler. Features: 304 Stainless Steel Construction Four Casters for easy movement. Two of the casters have locks Built-in centrifugal stainess steel pump with on/off switch 21 Food-Grade Noryl plastic plates included.  Double filtration kit available Built-in pressure gauge Maximum pump pressure is 2.5 bar (35 p.s.i.) Up to 600L (158 gal) Flow rate per hour 620x420x560mm/24x16.5x22 inches 90 lbs 1.5" Tri-Clamp inlet and outlet Pads should be placed in the machine rough-smooth-smooth-rough  

Read more less

Rolling cart wine plate filter Plates made from food-grade Noryl Built-in stainless centrifugal pump Built-in pressure gauge 1.5" tri-clamp inlet/outlet 1,200L/h wine filtering capacity Made in Italy by Marchisio Commercial plate filter featuring 41 20cm x 20cm plates. Included 110v 1/2hp, stainless motor will pump wine from your container and push it through the filter and into your aging tank or bottle filler. Features: 304 Stainless Steel Construction Four Casters for easy movement. Two of the casters have locks Built-in centrifugal stainess steel pump with on/off switch. 41 Food-Grade Noryl plastic plates included. Double filtration kit available Built-in pressure gauge Maximum pump pressure is 2.5 bar (35 p.s.i.) Up to 1200L (317 gal) Flow rate per hour 940x480x590mm/37x19x23 inches 114 lbs 1.5" Tri-Clamp inlet and outlet Pads should be placed in the machine rough-smooth-smooth-rough Minimum number of plates that can be used is 30  

Read more less

The Enolmaster Tandem Professional Filter Housing is designed to operate in conjunction with the Enolmaster Bottle Filling Machine. Enolmaster Tandem helps you save time by filtering and bottling at the same time. Place the filters in the housing and attach the hoses, then open the bypass valve on top of the filter housing. Place the Tandem Filter Housing inline between the product and the Enolmaster Filler. The Enolmaster Filling Machine draws the product from your tank and will pull the liquid through your filter housing, into the bottle. Fast filtering and bottling, easy to use, preserves product quality, easy to clean. Holds 3 Filter Cartridges. Requires 3 Filter Cartridges of the same Micron for use. Includes tubing to connect to Enolmaster Filling Machine Alcohol tolerance up to 18% ABV Filter Cartridges sold separately and listed at the bottom of this page Easy to Use The Tandem professional filter housing in conjunction with the Enolmaster professional vacuum filler. The machine creates the vacuum inside the bottle by sucking the liquid from the main container. Then the liquid is easily filtered and bottled in a single operation. Preserves the Product The filtering system is designed to preserve the integrity of the product. The filtering cartridges retain only the unwanted particles without altering the organoleptic qualities of the product. Easy to Clean The Tandem professional filter housing is easily cleaned after each use. In this way you will always have maximum hygiene in the bottling process.   Please note: Recommended for use with wine and beer only. Use with spirits and liqueurs above 18% ABV may result in damage to the filter housing.

Read more less

The best way to filter wine at home! Push wine from one keg through a plate filter and into another keg. No pumping, no oxidation, and total control over flow rates. The system can be expanded as needed by adding kegs or additional filter housings. All materials that come in contact with the wine are either stainless steel or food-grade, FDA-approved plastic or rubber. Kegs can be used for wine storage, and the gas system can be used anywhere a blanket of inert gas is needed. Complete filtering system includes one Nitrogen tank, dual gauge Nitrogen regulator, gas line assembly, two 5.5 gallon kegs and our FIL45B Wine & Beer Plate Filtering Kit. The kit includes a set of FIL46 Rough Filter Sheets. Additional sheets and sheets in other micron ratings can be selected from the You Might Also Need section below. Please Note:The Nitrogen tank is shipped empty and will need to be filled at your local welding supply shop. This kit will come with refurbished or converted Ball Lock Kegs

Read more less

A great accessory for the FIL45 Plate Filter. Use pressure to push beer/wine through the plate filter rather than gravity alone. Comes with a funnel top and stable base maintaining an excellent balance. Please refer to the manual below for complete instructions. BPA Free Made from high density polyethylene Max Temp Rating: 167°F (75°C) Includes 35" length of 5/16" ID x 7/16" OD tubing. Plate filter not included.  

Read more less

Benchtop plate filter for wine or oil Plates made from food-grade PPA Built-in ENOS 20 centrifugal pump Stainless ball valve and sample tap 280L/h wine filtering capacity Made in Italy by EnoItalia Benchtop style wine plate filter made from AISI 304 stainless steel with 20x20 food-grade PPA filter plates (10 plates). Includes ENOS 20 centrifugal pump. Features: Stainless ball valve Stainless sample tap Pressure gauge 220V single phase Input Voltage Required Bare Cord for wiring with the appropriate plug Wine Capacity: 130-280 L/h (34-73 gal/h) Oil Capacity: 130 L/h (34 gal/h) Dimensions: 23.6" L x 12.9" W x 17.3" H Weight: 64 lbs Please Note: This item may come with a bare cord or with a European style plug.  You will need a professional electrician to wire the pump with the appropriate plug.  

Read more less

Rolling cart plate filter for wine or oil Plates made from food-grade PPA Built-in ENOS 20 centrifugal pump Stainless ball valve and sample tap 900L/h wine filtering capacity Made in Italy by EnoItalia Made from AISI 304 stainless steel with 20x20 food-grade PPA filter plates (20 plates). Includes ENOS 20 pump with stainless body and impeller. Mounted to trolley cart with rolling casters. Features: Stainless ball valve Stainless sample tap Pressure gauge 220V single phase Input Voltage Required Wired with European-style 2-prong plug* Wine Capacity: 600-900 L/h (158-237 gal/h) Oil Capacity: 600 L/h (158 gal/h) Pump Barbs: 20 mm (0.78") Dimensions: 23.6" L x 19.7" W x 29.5" H Weight: 79 lbs *You will need a certified electrician to re-wire the unit with the appropriate 220V plug.  

Read more less

Reversing Plate kit for EnoItalia 20x20 Wine Plate Filters.  

Read more less

Rolling cart plate filter for wine or oil Plates made from food-grade PPA Built-in ENOS 20 centrifugal pump Stainless ball valve and sample tap 1,500L/h wine filtering capacity Made in Italy by EnoItalia Made from AISI 304 stainless steel with 20x20 food-grade PPA filter plates (40 plates). Includes EURO 20 flexible impeller pump. Mounted to trolley cart with rolling casters. Features: Stainless ball valve Stainless sample tap Pressure gauge 220V single phase Input Voltage Required Wired with European-style 2-prong plug* Wine Capacity: 900-1500 L/h (237-396 gal/h) Oil Capacity: 900 L/h (237 gal/h) Pump Barbs: 20 mm (0.78") Dimensions: 23.6" L x 19.7" W x 29.5" H Weight: 108 lbs *You will need a certified electrician to re-wire the unit with the appropriate 220V plug. 20 Plate unit pictured.  

Read more less

Rolling cart plate filter for wine or oil Plates made from food-grade PPA Built-in ENOS 20 centrifugal pump Stainless ball valve and sample tap 280L/h wine filtering capacity Made in Italy by EnoItalia Made from AISI 304 stainless steel with 20x20 food-grade PPA filter plates (10 plates). Includes ENOS 20 pump with stainless body and impeller. Mounted to trolley cart with rolling casters. Features: Stainless ball valve Stainless sample tap Pressure gauge 220V single phase Input Voltage Required Wired with European-style 2-prong plug* Wine Capacity: 130-280 L/h (34-73 gal/h) Oil Capacity: 130 L/h (34 gal/h) Pump Barbs: 20 mm (0.78") Dimensions: 23.6" L x 19.7" W x 29.5" H Weight: 70.5 lbs *You will need a certified electrician to re-wire the unit with the appropriate 220V plug. 20 Plate unit pictured.  

Read more less

Condition: Used - Good This unit is used. It shows wear from use but is in good condition and works perfectly. It may have cosmetic defects or show other signs of previous use.  It is still covered by our No Hassle Return Policy and 1 Year Warranty Policy.   Rolling cart plate filter for wine or oil Plates made from food-grade PPA Built-in ENOS 20 centrifugal pump Stainless ball valve and sample tap 900L/h wine filtering capacity Made in Italy by EnoItalia Made from AISI 304 stainless steel with 20x20 food-grade PPA filter plates (20 plates). Includes ENOS 20 pump with stainless body and impeller. Mounted to trolley cart with rolling casters. Features: Stainless ball valve Stainless sample tap Pressure gauge 220V single phase Input Voltage Required Wired with European-style 2-prong plug* Wine Capacity: 600-900 L/h (158-237 gal/h) Oil Capacity: 600 L/h (158 gal/h) Pump Barbs: 20 mm (0.78") Dimensions: 23.6" L x 19.7" W x 29.5" H Weight: 79 lbs *You will need a certified electrician to re-wire the unit with the appropriate 220V plug.  

Read more less

Premium 316 stainless steel construction ensures durability and corrosion resistance, ideal for demanding beverage production environments Wide compatibility with a range of filter cartridges offers adaptability and customization for optimal filtration results in beverage making processes Multiple housings easily work in tandem for sequential filtration with cartridges of different micron ratings, ensuring thorough removal of bacteria for pristine final products The BevBright 30" Stainless Cartridge Filter Housings are designed to streamline your beverage production with unmatched purity and efficiency. Made from premium electropolished 316 stainless steel, these filter housings protect against contamination, ensuring your final product meets the highest standards of quality and taste. Engineered to resist corrosion in challenging environments, they offer durability and reliability. These stainless steel filter housings are essential for precision filtration in beverage production. When used with a sterile filter cartridge, they effectively remove yeast and bacteria, delivering pure, pristine liquid. Tri-clamp ports ensure easy integration into your setup, and the option to daisy-chain filters allows for efficient multi-stage filtration, prolonging the life of your sterile cartridges. BevBright filter housings are compatible with a wide range of filter cartridges, providing the flexibility to meet your specific filtration needs, from standard to sterile filtration. Each unit comes complete with hardware and ready for immediate use. Trust BevBright 30" Stainless Cartridge Filter Housings to maintain the purity and excellence of your beverage from start to finish. Made from 316 Stainless Steel Polish: Ra<0.4um Hardware Included: (2) 1.5" T.C. Pressure Gauges (2) 1.5" T.C. Butterfly Valves (1) 1.5" T.C. Tee (1) Top Relief Valve (2) 1/2" T.C. Drain Valves Clamps & Gaskets Compatible with Scott Labs' ScottCart Code 7: 226 Twist & Lock 30" Cartridges Example images shown. The Filter Housing also includes a 1.5" T.C. Tee & Pressure Gauge and 1/2" T.C.Drain Valves that are not pictured.

Read more less

Rolling cart plate filter for wine, beer, cider, and distilling Plates made of high temperature Noryl plastic capable of being steam sterilized Double filtration kit included as standard Built-in pressure gauges, sight glasses, and sample valves 1.5" tri-clamp inlet/outlet w/ butterfly valves (40) 40cm x 40cm plates 4,000L/h filtering capacity The BevBright commercial plate filter features external stainless steel piping with built-in pressure gauges, sight glasses, and sample valves. Easily connect hoses to the included 1.5" tri-clamp butterfly valves. Double filtration kit comes standard. Features: 304 Stainless Steel Construction Up to 4,000L (1,056 gal) flow rate per hour Rolling casters for easy movement Drip collection tray 40 plates included Double filtration kit included (2) Built-in pressure gauges, sight glasses, and sample valves 1.5" Tri-Clamp inlet and outlet 67.7" x 26" x  x 35.5" 518 lbs Pads should be placed in the machine rough-smooth-smooth-rough CE Compliant Please note: This unit comes with white plates rather than black plates as seen in the example photo. Updated images coming soon. Warning: You will need to remove the unit from the shipping pallet using a forklift and straps. Do not use a fork lift to directly lift from the bottom of the unit. Doing so may damage the bottom tray.

Read more less

Rolling cart plate filter for wine, beer, cider, and distilling Plates made of high temperature Noryl plastic capable of being steam sterilized Double filtration kit included as standard Built-in pressure gauges, sight glasses, and sample valves 1.5" tri-clamp inlet/outlet w/ butterfly valves (20) 40cm x 40cm plates 2,000L/h filtering capacity The BevBright commercial plate filter features external stainless steel piping with built-in pressure gauges, sight glasses, and sample valves. Easily connect hoses to the included 1.5" tri-clamp butterfly valves. Double filtration kit comes standard. Features: 304 Stainless Steel Construction Up to 2,000L (528 gal) flow rate per hour Rolling casters for easy movement Drip collection tray 20 plates included Double filtration kit included (2) Built-in pressure gauges, sight glasses, and sample valves 1.5" Tri-Clamp inlet and outlet 47.5" x 26" x 35.5" 363 lbs Pads should be placed in the machine rough-smooth-smooth-rough CE compliant Please note: This unit comes with white plates rather than black plates as seen in the example photo. Updated images coming soon.

Read more less

Part #9 in attached plate filter instuctions.  

Read more less