Wine Making Hardware

For clean, straight cuts this 2-in-1 cutter is hard to beat. Developed specifically for EVABarrier draft line, but compatible with any tubing that is 3/8" OD or smaller. Features an 8mm jaw on the back to easily pull the collet back when removing line from Duotight fittings.   Kegland Part number: KL07689  

Read more less

Ease of Use! Easily connect and disconnect your water line to various equipment. This set includes one Male GHT x Male QD and One Female GHT x Female QD. GHT stands for Garden Hose Thread. Flow Direction These QD's must be placed in such a configuration that water is always exiting the female portion of the QD and entering the male portion of the QD. For example the female x female portion is placed on the end of the hose while the male portion is connected to your equipment. Adapt it to your needs We sell several adaptor pieces that allow you convert GHT to male or female 1/2 inch pipe thread. Please Note: This product will NOT work with our Stainless or Plastic Quick Disconnects.

Read more less

The BrewBuilt tri-clamp thermometer features a large 3" face for easy reads and 6" probe for deep penetration into your conical fermenter or T.C. kettle. Dial face reads from 0-220°F and -10-100°C. 3" dial face 6" probe 1.5" T.C. Reads in °F and °C

Read more less

Female Garden Hose Thread on one side with 1/2" MPT on the other. Useful for customizing your chilling configuration! A gasket is included inside the female garden hose thread portion.

Read more less

Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive more in late December. For an in stock 5 lb CO2 tank option, please see our D1050.   Made from corrosion resistant, engineered Aluminum New high quality CGA-320 valve DOT approved Brand new aluminum 5 lb CO2 tank made from high strength aluminum alloy and high quality CGA320 valves. Because it is made of aluminum rather than steel you can feel confident that it won’t rust. It’s called a 5 lb tank because it holds 5 lbs of compressed (liquified) CO2. 5 lbs of CO2 is enough to dispense about 8 to 9x 5-gallon kegs of homebrew. Aluminum tanks are superior to steel because they do not rust. All tanks are shipped empty. To have tanks filled you will want to visit your local welding supply shop. Because you are purchasing a new tank you can choose to either have it filled or to exchange it for a filled tank at your local gas supplier. If you have this tank filled the local gas supplier is responsible for affixing the correct neck label that identifies the gas being put in the cylinder. Tanks should always be stored in an upright position. Features: Made from corrosion resistant, engineered Aluminum Brushed finish Thick, durable cylinder walls 18" T x 5.25 Ø DOT approved New high quality CGA-320 valve Light weight compared to steel tanks  

Read more less

Push product or sanitizer from one keg to the next. Two black, beverage quick disconnects with flare fittings attached via a one foot piece of beverage line.

Read more less

Brand new, all-stainless construction ball lock keg Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Set your sights on a brand new Torpedo Keg! The patented, D794,899, sleek all-stainless design represents the pinnacle of quality in ball lock homebrew kegs. With features like welded stainless handles, the ability to stack with fittings in place, amazing quality and a great price we think these kegs will become the standard by which other kegs are measured.    Quality First The first thing we at MoreBeer! check out is interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. These kegs are machine welded and exceed our standards for quality. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. In and Out is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Taking your keg on the go? Don't leave home without a custom fitted Torpedo Keg Sleeve! Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions:   Height (in.) Diameter (in.) 1.5 Gal 10.25 9 2.5 Gal 14.75 9 5 Gal 23 9 Please Note: These are about 1/2" wider than standard Ball Lock Cornelius Kegs. Need something a bit slimmer?  Check out our lineup of Slimline Torpedo Kegs!  

Read more less

The ideal vessel for serving pre-mixed cocktails and other concoctions on draft Easily pour in your beverage of choice through the wide corny-style lid opening without needing to remove the spear Doubles as a line cleaning keg Rolled handles for a comfortable grip Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams The Torpedo Cocktail Keg is the ideal vessel for serving pre-mixed cocktails and other concoctions on draft. The corny keg style lid makes it easy to pour in your beverage of choice without having to fuss with removing the spear like with standard commercial sanke kegs. Hook up a D-Style keg coupler to begin carbonating the beverage from the bottom up. These kegs provide the added advantage of fully carbonating the entire cocktail. When making drinks on the fly, carbonation is lost quickly since you're mixing carbonated and still ingredients together. But when served from a fully carbonated keg, you can enjoy the bubbles in your glass for longer! Draft lines needing some love? The Torpedo Cocktail keg easily doubles as a line cleaning keg. Simply fill with a batch of LLC or BLC to give your bev lines a little TLC. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions:   Height (in.) Diameter (in.) 1.5 Gal 10 9 3/8 2.5 Gal 13 1/4 9 3/8  

Read more less

This Oxygenation System pumps pure oxygen into your cooled wort using a disposable oxygen tank and stainless steel diffusion stone. Takes a mere 1-2 minutes of operation to achieve adequate oxygen levels. Comes with a regulator for disposable oxygen tank, sterile inline filter, our threaded .5 micron stainless steel oxygenation stone and tubing. Yeast need oxygen to make good beer. The problem is that after boiling for an hour the wort is void of oxygen. Fermentations with low levels of oxygen will produce yeast that start slower, have sluggish ferments, and are more likely to poop-out and stop fermenting. On the contrary, fermentations that have been infused with oxygen will have healthier yeast that start faster, ferment faster, have a greater tolerance to alcohol, produce beers with less residual sugar, and produce better overall flavors. Currently, the standard practice of getting oxygen to the yeast is to splash the wort as it enters the fermenter or to shake the fermenter once full. This practice is definitely better than nothing, however it is impossible to infuse enough oxygen by shaking or splashing and the air you do infuse is usually contaminated to some extent. Please Note: Disposable Oxygen tank is Not Included.  These are available at some hardware stores. Each disposable oxygen tank will last for approximately 10-15 five gallon batches. About the inline filters: There are two sides to the filter - an "in" and an "out". The direction you use doesn't matter, however, you want to take note of which way you first push air through it and always keep it that way. There is an arrow on the edge of the filter housing that we use to keep the air flow going one direction when using it. The filter should never get wet, so don't dunk it in sanitizer. If you want to clean the outside of it, use Alpet D2. To store the filter, use a little tinfoil on the "In" of the filter and store in a zip-lock bag. Oxygen Regulator Features: 1/4" Barb Output Max Delivery Pressure: 100 PSI Max Flow Rate:  180 CFH Regulator is Left Hand Thread Stainless Steel Actuating Rod Machined brass body with adjusting cap, piston and hose connection

Read more less

1.5" tri-clamp with 1/2" BSP male threads. Made from 304 stainless steel. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" and 3/4" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL01847  

Read more less

Stainless lock nut. 1/2" FPT

Read more less

This is a ball-lock type quick disconnect that is constructed from stainless steel for lifetime longevity. This product is for the White Gas In connection on the left, for the Black Beverage Out connection, see our KEG732. 2 1/8" H Please note: the outer bushing on the disconnect is made from chrome-plated brass. All parts that come into contact with liquid are stainless. Kegland Part Number: KL03001

Read more less

The Slimline Torpedo Keg series features a smaller diameter to maximize the space in your kegerator or keezer Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Brand new, all-stainless construction ball lock keg Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Torpedo Kegs too wide? Want to squeeze another keg in your kegerator? The patented design, D794,899, of the Slimline Torpedo Keg is 9% more slim than the classic model with all the same great features. Coming in at about 1/4" thinner than standard Ball Lock Cornelius Kegs, this keg has welded stainless handles and the ability to stack kegs with fittings still in place all at a great price. Quality First Here at MoreBeer! we love nothing more than quality interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. Torpedo kegs are machine welded and exceed our standards for quality. This weld quality is possible because these kegs are made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. “In” and “Out” is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Taking your keg on the go? Don't leave home without a custom tailored Slimline Torpedo Keg Sleeve! Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions:   Height (in.) Diameter (in.) 1.5 Gal 11 8 3/8 2.5 Gal 15 5/8 8 3/8 5 Gal 25 1/2 8 3/8   For a slightly shorter keg, see our Standard Torpedo Kegs!  

Read more less

Strong stainless screw clamp that fits tubing with outer diameter between 2.75 and 3.62 inches.

Read more less

Replacement air tubes for variable capacity tanks. 115 cm tube fits LA Inox 1850 Liter tanks. Please note: These tubes are only compatible with Marchisio brand tanks. They will not work with Speidel or other brands of variable volume tanks.

Read more less

Adapts 2" Tri-Clover fitting to 1" Male Pipe Thread. 304-type stainless steel.

Read more less

Speidel 1" DIN to 1.5" TC adapter. If you have a mixture of TC and DIN fittings, there is finally an adapter to help you connect everything together. To top it all off it is made with the expert craftmanship of Speidel.

Read more less

Extension tube with 2" tri-clamp fittings on both ends. 10" in length. Made from 304 stainless steel. Kegland Part Number: KL10665

Read more less

This Stainless Steel BSPP barb will connect any tubing with a 5/16" ID line to any fitting with a 1/4" Female BSPP connection. The barb is slightly oversized at 8mm (0.315") compared to 5/16" (0.3125") which will give you a tighter connection with your tubing. KegLand Part Number: KL06637

Read more less

20 PSI replacement spring for pressure relief valves.  All SS, works with our D1830, as well as a replacement for our Counter Pressure Bottle Fillers.

Read more less

Replacement knob for Kegland CO2 tanks. Compatible with tanks sized 2.5 - 20 lbs. KegLand Part Number: KL30625

Read more less

The Duotight In-Line Regulator works with both gas and liquid. Easily adjust the flow can be adjusted with the yellow adjustment knob. 6.35 mm Duotight fittings at both inlet and outlet make this unit perfect for use with 6.35 mm OD tubing (D1723C or D1727C).  Features an integrated pressure gauge so you can quickly and easily dial in your pressure setting. The analog gauge is removable and can be swapped out with a gauge of a different pressure range or it can be swapped out for the Digital Mini Pressure Gauge. The size of the Duotight connection and the extended 0-150 PSI pressure range makes this model perfect for stepping down the pressure of your mains water line for use with water filtration or RO systems. Specifications: Made from food grade acetal Stainless screws Easily disassembles for cleaning 6.35mm (1/4") Duotight fittings at both ends Interchangeable pressure gauge Gauge reads from 0-150 psi Made with quality EPDM seals Wall mountable WARNING: Do not exceed gauge pressure. Exceeding the pressure range will damage the gauge. Kegland Part number: KL26918

Read more less

The foot for the swing arm on the keg lid. They are often missing on used kegs. 

Read more less

We made this socket so that you can easily remove gas and beverage body connects on Pin Lock style kegs. (Currently a 3/8" drive)

Read more less