Wine Making Hardware

These stainless steel butterfly hose clamps are the ideal choice for connecting silicone tubing to quick disconnects, pumps, and more. The butterfly thumb screw allows for toolless tightening and untightening, so you can build out or break down your system without rummaging through the toolbox for the right screwdriver. Fits 1/2 in. OD to 1 in. OD tubing. Actual size of the clamp is 14-25 mm (0.55-0.98 in.). Comes in a convenient zip lock bag.

Read more less

Stainless steel barb fitting. 1/2" male BSP x 13mm barb (0.51"). KegLand Part Number: KL03629  

Read more less

Type C Camlock Fitting. Female Camlock with 1/2" Barb (13mm). Camlocks are considered by many to be the superior quick connect fitting. They have a higher working pressure and hold a tighter seal than quick disconnect fittings, making them less likely to leak while in use. Locking and unlocking the female pieces may require two hands, but it's a small price to pay for long-lasting reliability. 304 Stainless steel construction. 150 psi working pressure. Kegland Part Number: KL04497

Read more less

1.5" tri-clamp "clean in place" spray ball. A pump capable of 29 PSI minimum is recommended for this product.

Read more less

End cap for 3" tri-clamp fittings. Made from 304 stainless steel.

Read more less

3" x 2" tri-clamp concentric reducer. Made from 304 stainless steel.  

Read more less

The gaskets on the body connects that the ball or pin lock fittings slide over. 7/16" ID with a 3/32" cross section. Made of FDA BUNA-N rubber. We also use this as a replacement for the smaller compression ring in our 1/2" Compression fittings so that you can create a snug fit in a Sanke keg conversion kit without permanently compressing a ring on the pick up tube.

Read more less

Neoprene keg sleeves for standard Torpedo Kegs. For the Slimline series sleeves, see KEG651. 6mm thick. The 5-gallon sleeve is also compatible with 1/6 bbl or sixtel commercial sanke kegs.

Read more less

The Duotight In-Line Regulator works with both gas and liquid. Easily adjust the flow can be adjusted with the yellow adjustment knob. 8 mm Duotight fittings at both inlet and outlet make this unit perfect for use with EVABarrier 8 mm OD tubing (D1717 or D1718).  Features an integrated pressure gauge so you can quickly and easily dial in your pressure setting. The analog gauge is removable and can be swapped out with a gauge of a different pressure range or it can be swapped out for the Digital Mini Pressure Gauge. Stepping Down Pressure The ideal regulation scenario occurs when the inline regulator steps down the output pressure to at least 10 PSI less than the inlet pressure. For example, if the inlet pressure is 30 PSI, the regulator effectively manages a range from 0–20 PSI on the output side ensuring optimal performance and stability. Ideal regulation scenario (10 PSI less than inlet pressure) Example of 30 PSI inlet translating to 0–20 PSI output Specifications: Made from food grade acetal Stainless screws Easily disassembles for cleaning 8mm (5/16") Duotight fittings at both ends Interchangeable pressure gauge Gauge reads from 0-60 psi Made with quality EPDM seals Wall mountable WARNING: Do not exceed gauge pressure. Exceeding the pressure range will damage the gauge. Kegland Part number: KL15035  

Read more less

PVC tubing for gas and beer lines in kegging systems. 3/8 in inside diameter tubing with thick walls.  

Read more less

Used primarily in aeration and oxygentation systems that call for 1/8" ID line. 3/16" OD.  

Read more less

Type F Camlock Fitting. Male Camlock with 1/2" BSP. Camlocks are considered by many to be the superior quick connect fitting. They have a higher working pressure and hold a tighter seal than quick disconnect fittings, making them less likely to leak while in use. Locking and unlocking the female pieces may require two hands, but it's a small price to pay for long-lasting reliability. 304 Stainless steel construction. 150 psi working pressure. Kegland Part Number: KL04510

Read more less

Use this 4" T.C. end cap to attach an airlock to your kegmenter unit. The hole measures 13/16", which is perfect for a #3 stopper (FE410VS). Kegland Part Number: KL06163

Read more less

Silicone gasket for 4" tri-clamp connection. Temperature rated from -58°F to 446°F.  

Read more less

Full Coupler with 1" Female Pipe Thread. Full couplers have threads for insertion from both sides.

Read more less

Not sure what bung is right for you? We got your back! Get all the Breathable Bungs with this complete set. Includes: Breathable Carboy Bung Breathable Universal Bung Breathable Barrel Bung Breathable Bung for Glass Carboys A breathable Silicone stopper that acts as both a stopper and an airlock. Unique design allows CO2 pressure to escape but keeps Oxygen and airborne contamination out. This quickly became our stopper of choice for wine, and is a popular style used by numerous commercial wineries. Also has great application for beer ferments: It will create a vacuum if fermenting wort cools (as opposed to pulling water in from your traditional airlock.) Airtight seal is great for extended fermented lager when CO2 production is still present but very slight. Fits 3, 5, 6 & 6.5 gallon glass carboys, 1 gallon bottles, growlers, and 500 mL flasks. Replaces Stopper Sizes #6, #6.5, #7, #8 Stopper Measurements: 0.94" x 1.48" (24 mm x 37.5 mm) Universal Breathable Bung This CellarScience Bung has a ridge to keep it from getting sucked in and self-sealing vent holes to let air out but not in. They have a gentle taper, so they don’t slip out during use.  They are also very easy to clean and sanitize. This a perfect fit for a 1.5” TC ferrules, Fermonsters, and Vintage Shop Plastic carboys. Replaces Stopper Sizes #8, #9. #10 Stopper Measurements: 1.36" x 1.89" (34.5 mm x 48 mm) Breathable Barrel Bung We recently discovered this premium breathable silicone barrel bung and were immediately impressed with its robust design and features. To start with, the ridge really helps make bung removal effortless. The bung acts as an airlock and allows the release of CO2 while maintaining a seal against oxygen coming in. This makes the bung ideal for alcoholic or malolactic fermentation in barrels or tanks. Fits 30- and 60-gallon barrels as well as the hole in the lid of most Variable Volume tanks! Also fits perfectly in a 2" tri-clamp ferrule Replaces Stopper Sizes #10 , #11, #12 Stopper Measurements: 1.65" x 2.19" (42 mm x 55.5 mm) The flapper stopper protrudes roughly 2.5" from the stopper

Read more less

3000psi gauge tells tank pressure. Left hand thread replacement gauge for some brand regulators.

Read more less

For the gas in side. Stainless steel construction, approximately 1.5" in length.

Read more less

Neoprene keg sleeves for Slimline Torpedo Kegs. For the standard size Torpedo keg sleeves, see KEG650. Also compatible with standard cornelius kegs. 6mm thick.

Read more less

2" TC Ferrule for welding onto a tank or section of pipe. 304-type stainless steel. ID is approximately 1-7/8th.

Read more less

Teflon gasket with 304 stainless mesh screen for 1.5" tri-clamp connections. Can be used as a filter screen to trap large particulates passing through T.C. fittings. Often used for distillation to retain activated carbon for filtering neutral spirits or used in pot distillation to retain botanicals in the vapor stream. This screen can also be used with the 1.5" Hop Bong as an inline filter. The screen has a mesh size of 7 which will block particles larger than 2.83mm or 2830 microns. This slightly larger mesh size makes this screen ideal for use in a distillation basket. KegLand Part Number: KL28516

Read more less

Please note: This stopper was designed for use with the BrewBuilt CoolStix which has been discontinued. Two of the holes are for an airlock and thermowell, but the third 1/2" hole was intended for the CoolStix and you will need to plug it or utilize it how you see fit. This #10 3-hole silicone stopper is used alongside the BrewBuilt CoolStix for Carboys. The holes are for a 1/2" CoolStix, an airlock, and a thermowell. The holes measure 0.500", 0.413", & 0.375" Compatible with Fermonsters and our Plastic PET Carboys listed below under "You Might Also Need".

Read more less

Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive more in late December. Brand new aluminum 10 lb CO2 tank made from high strength aluminum alloy and high quality CGA320 valves. Because it is made of aluminum rather than steel you can feel confident that it won’t rust. It’s called a 10 lb tank because it holds 10 lbs of compressed (liquified) CO2. 10 lbs of CO2 is enough to dispense about 20x 5-gallon kegs of homebrew. Aluminum tanks are superior to steel because they do not rust. All tanks are shipped empty. To have tanks filled you will want to visit your local welding supply shop. Because you are purchasing a new tank you can choose to either have it filled or to exchange it for a filled tank at your local gas supplier. If you have this tank filled the local gas supplier is responsible for affixing the correct neck label that identifies the gas being put in the cylinder. Tanks should always be stored in an upright position. Features: Made from corrosion resistant, engineered Aluminum Brushed finish Thick, durable cylinder walls 20.75" T x 6.875 Ø DOT approved New high quality CGA-320 valve Light weight compared to steel tanks  

Read more less

These stainless stepless clamps tighten in an exact circle, making them ideal for use with draft lines. Suitable for 1/2" OD tubing (12-14 mm OD). Comes in packs of 20 clamps. Stepless Clamp Tool sold separately - H1006 Kegland Part Number: KL06705

Read more less