Products

This piece sits between the Faucet and the Faucet Knob Lever Collar. It creates the friction when opening and closing the faucet.

Read more less

The second washer of a two part set that is used to allow motion of lever. Hard white material.

Read more less

Fix your old, stuck, or leaky faucet with new washers! Most faucets that aren't working properly, just need a good cleaning and some new washers Fits most American beer faucets, including D1200, D1205, D1207, and D1215 Does not work on stout, forward sealing, or European faucets   Fix an old faucet that is still functionally sound but is old, leaking or just hard to use. Fits our faucets D1200, D1205,D1207, & D1215 and 95% of all beer faucets ever made. Does not work on stout faucets, the sealed forward faucets, Perlick faucets, nor European faucets.

Read more less

Stainless levers are used to replace brass levers because of their strength and ability to not react with beer. Manufactured by Tap-Rite. Unlike brass levers, which sometimes snap if the faucet is stuck, stainless levers are stronger and eliminate the risk they will break at the worst time.... when the beer is flowing. 

Read more less

This washer seals the sliding shaft. It often becomes brittle with age and the faucet will drip.

Read more less

Stainless steel draft shank with collar and lock nut. Dimensions: 4-1/8" - Shank Length 3" - Thread Length 2-3/4" - Pass Through Length

Read more less

Comes with a welded 3/16" nipple, back nut, and plastic collar. It requires a 1" hole for installation. When set in place, the shank will only have about 1-1/4" of length to pass through your wall or fridge door, due to the length of the collar and back nut. Installation note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. Dimensions: 3-1/8" - Total Length (Tip to Tip) 2-1/2" - Shank Length (Without Nipple) 1-1/8" - Thread Length 1-1/4" - Pass Through Length

Read more less

Comes with a back nut, plastic collar, hex nut, and a 1/4" barb. Requires a 1" hole saw for installation. Due to the length of the back nut and collar, the total length of the shank will be about 2 3/4". Installation note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. Dimensions: 5-1/4" - Total Length (Tip to Tip) 4-1/8" - Shank Length (Without Nut & Nipple) 3" - Thread Length 2-3/4" - Pass Through Length 1/4'' - Bore

Read more less

Stainless Steel Faucet Shank Dimensions: 6-1/4" - Total Length (Tip to Tip) 5-1/8" - Shank Length (Without Nut & Nipple) 3-3/4" - Thread Length 4-5/8" - Pass Through Length 3/16 in. Nipple Installation note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling.

Read more less

Comes with a back nut, plastic collar, and a welded 1/4" nipple. Requires a 1" hole saw for installation. Due to the length of the back nut and collar, the total length of the shank will be about 4 3/8". Installation note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. This is a Chrome Plated Brass unit. Dimensions: 6-1/4" - Total Length (Tip to Tip) 5-1/2" - Shank Length (Without Nut & Nipple) 4-1/8" - Thread Length 5-1/4" - Pass Through Length

Read more less

Comes with a back nut, plastic collar, and a welded 3/16" nipple. Requires a 1" hole saw for installation. Due to the length of the back nut and collar, the total length of the shank will be about 4 3/8". Installation note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. Dimensions: 6-1/4" - Total Length (Tip to Tip) 5-1/2" - Shank Length (Without Nipple) 4-1/8" - Thread Length 5-1/4" - Pass Through Length

Read more less

You can use pass through shanks for beer entry through the back side of a cooler. Drill a 1" hole through the cooler, insert the shank, and use the two attached nuts to tighten up on the cooler. You will need nuts and nipples of the size line you are working with as well as hose clamps. We do not use pass through shanks in our boxes because we drill a hole that is same size as the line so we can pull it back in when we are traveling. However there might be instances where they would be appropriate. Pass through shanks can also be used to put through the side of a refrigerator to pass a gas line through. Installation Note: On a fridge there are generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. This is a stainless steel shank with chrome plated brass hex nuts. Dimensions: 3" - Shank Length  3" - Thread Length 1-7/8" - Pass Through Length Max length with hex nuts at either end Does not account for nuts/nipples you may install Male Beer Thread (5/8" BSP)

Read more less

You can use pass through shanks for beer entry through the back side of a cooler. Drill a 1" hole through the cooler, insert the shank, and use the two attached nuts to tighten up on the cooler. You will need nuts and nipples of the size line you are working with as well as hose clamps. We do not use pass through shanks in our boxes because we drill a hole that is same size as the line so we can pull it back in when we are traveling. However there might be instances where they would be appropriate. Pass through shanks can also be used to put through the side of a refrigerator to pass a gas line through Installation Note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. This is a stainless steel shank with chrome plated brass hex nuts. Dimensions: 4" - Shank Length 4" - Thread Length 2-3/4" - Pass Through Length Max length with hex nuts at either end Does not account for nuts/nipples you may install Male Beer Thread (5/8" BSP)  

Read more less

Stainless Steel Faucet Shank Dimensions: 3-3/4" - Total Length (Tip to Tip) 2-1/8" - Shank Length (Without Nut & Nipple) 1-1/4" - Thread Length 11/16" - Pass Through Length Installation note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling.

Read more less

Comes with a back nut, plastic collar, hex nut, and 8 mm Duotight Adapter compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Requires a 1" hole saw for installation. When set in place, the shank will only have about 2 1/2" of length to pass through your wall or fridge door, due to the length of the collar and back nut. Installation note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. Dimensions: 5-1/8" - Total Length (Tip to Tip) 4" - Shank Length (Without Nut & Barb) 3" - Thread Length 2-1/2" - Pass Through Length Kegland Part number: KL11945

Read more less

Comes with a back nut, plastic collar, hex nut, and a 1/4" barb. Requires a 1" hole saw for installation. When set in place, the shank will only have about 2 1/2" of length to pass through your wall or fridge door, due to the length of the collar and back nut. Installation note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. Dimensions: 5-1/8" - Total Length (Tip to Tip) 4" - Shank Length (Without Nut & Barb) 3" - Thread Length 2-1/2" - Pass Through Length Kegland Part number: KL01113

Read more less

Comes with a back nut, plastic collar, hex nut, and 8 mm Duotight Adapter compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718). Requires a 1" hole saw for installation. When set in place, the shank will only have about 4-1/2" of length to pass through your wall or fridge door, due to the length of the collar and back nut. Installation note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. Dimensions: 7-1/8" - Total Length (Tip to Tip) 6" - Shank Length (Without Nut & Barb) 5" - Thread Length 4-1/2" - Pass Through Length Kegland Part number: KL11952  

Read more less

Stainless Steel Faucet Shank for running beer through the door of a kegerator or keezer.  1/4" Barb and collar are included, and reduce the through wall length to 4-1/2". Dimensions: 7-1/8" - Total Length (Tip to Tip) 6" - Shank Length (Without Nut & Barb) 5" - Thread Length 4-1/2" - Pass Through Length Kegland Part number: KL01120

Read more less

This matte black tower shank is the ideal match for the NukaTap Stealth Bomber faucet and comes with a Duotight-ready tailpiece. Quickly connect 8 mm OD draft line to the shank by pairing it with DUO100. Please note these shanks are not compatible with Perlick brand faucets. KegLand Part Number: KL20084

Read more less

Replacement O-ring for beer faucet tower shanks D1239 and D1242. This O-ring sits underneath the coupling nut of the shank, behind the teeth where the shank connect to the faucet. KegLand Part Number: KL88067

Read more less

This shank's small design makes it perfect for attaching a faucet to a tower, and comes with a Duotight-ready tailpiece. Quickly connect 8 mm OD draft line to the shank by pairing it with DUO100. Please note these shanks are not compatible with Perlick flow control faucets. Kegland Part number: KL01137

Read more less

This shank's small design makes it perfect for attaching a faucet to a tower. Please note these shanks are not compatible with Perlick brand faucets. Kegland Part number: KL01090

Read more less

For the do-it-yourself person, this is the piece that you see at the bottom of most handles, you must also get the D1298B if you want to screw it into a wood tap handle. (5/16" top threads and 3/8" bottom threads)

Read more less

For the do-it-yourself person, this is the piece that you see at the bottom of most handles. You must also get the D1298B if you want to screw it into a wood tap handle. (5/16" top threads and 3/8" bottom threads).

Read more less