Products

These quick disconnects feature 3/8" barbed fittings which can be used with 3/8" line. The quick disconnect functionality is activated by a shrouded thumb latch. The temperature range is -40F to 180F. They can handle a vacuum to 120 psi - so you need not worry about them leaking gas. The internal valve spring is 316 type stainless steel and the o-ring is food grade buna-n.   This is a direct replacement to the Female Quick Disconnect with 3/8" Barbs that is featured on the BrewBuilt CoolStix™.

Read more less

These quick disconnects feature 1/4" barbed fittings which can be used with either 3/16", 1/4" or 5/16" line. The quick disconnect functionality is activated by a shrouded thumb latch. The temperature range is -40F to 180F. They can handle a vacuum to 120 psi - so you need not worry about them leaking gas. The internal valve spring is 316 type stainless steel and the o-ring is food grade buna-n.

Read more less

For use with our FIL45 series of plate filters. These pads will provide between 1-2 Micron filtration. Each filter pad set is good for approximately 5 gallons of beer when the beer has been filtered by the previous size pads or you are starting with the rough filters. These pads are designed to be thrown away after one use.

Read more less

For use with our FIL45 series of plate filters. These pads will provide between 5-7 Micron filtration. Each filter pad set is good for approximately 5 gallons of beer. These pads are not designed to be back flushed and reused and should be used in one session.

Read more less

This cartridge filter is designed to be installed inline between two ball lock Cornelius kegs. The design uses Argon or Nitrogen gas pressure to push wine out of the full keg, through the filter and into the clean keg. This kit includes a cartridge to filter out particles down to 1 micron in size, which is considered a "fine" or "polish" filtration. This is a fine place to start if your wine is already naturally very clear from successive rackings, or you have pre-fined the wine. If you do not wish to wait for racking to be effective or to pre-fine the wine ahead of filtration, MoreWine! suggests that you start with either our 5 micron or 3 micron cartridge and put the wine through successively finer filter media until you reach your desired level of clarity. The Beer and Wine Filtering Kit comes with one 10" filter housing, a 1 micron 10" spun poly sediment filter, fittings for connection to the filter housing, 3' of beverage line, clamps, and two beverage out ball lock quick disconnects. Spun-polypropylene filters are disposable filters and cannot be effectively cleaned for reuse. However, you can filter multiple kegs with one filter cartridge. Most customers report being able to filter 10-15 gallons of product, however you should be aware that your results will vary depending on the cloudiness of your beer or wine. 5-10 micron is considered rough filtration, 3 micron will remove most yeast, and 1 micron filtration will remove almost all yeast. All filters are rated nominal (will filter out 80-85% of matter at given rating).

Read more less

A deluxe hydrometer for beer or wine with built-in thermometer and correction scale that allows you to instantly correct your hydrometer readings for temperature. A hydrometer reads accurately at 60 Fahrenheit. Temperatures above and below 60F require that you add or subtract from your reading. Like the basic model, the deluxe hydrometer also features three scales - specific gravity, potential alcohol and Brix (Balling). 12.75" long. Current range is .990 to 1.160

Read more less

Most breweries and wineries use a large plate filter system to achieve clear product. Now you can do the same at home with two corny kegs. Our Beer and Wine Plate Filter Kit has a larger surface area, which means more yeast and particulate extraction than our cartridge filter, and comes with our plate filter, two disposable filter pads, tubing, flare fittings, and two flare beverage ball locks. Each filtering session requires two pads at a time, and each pad must be the same micron to work. The beer or wine is pushed out of the keg and into the housing at 5 PSI, where it passes on either side of the filter housing, then gets forced from the center through the pads, where it is then pushed out into your clean keg. The rough sides of both filters should be facing each other on the inside of the filter, so the smooth sides face outward. Each filter pad set is good for approximately 5 gallons of beer when the beer has been filtered by the previous size pads or you are starting with the rough filters. These pads are not designed to be back flushed and reused and should be used in one session.

Read more less

A traditional brush for cleaning 12 to 22oz beer bottles. Many customers like this design for its rounded bristles at the end of the brush that do a great job cleaning the lower half of the bottle.  Includes circular metal loop for hanging.  Bristles are 2.75" in diameter with an overall length of 16".  

Read more less

Blank cardboard 6-pack carrier for 12 oz bottles Keep a couple of these on hand to easily transport your bottled beer White, for 12 oz bottles. Put bottles in them. Carry them around. A lot easier than carrying six loose bottles in one hand. A great idea for gifts.

Read more less

These 2-Part customizable beer bottle labels will give your homebrew a distinctive upscale look.   With these unprinted sheets of adhesive 2-Part Labels you can easily create your own custom beer bottle labels. The pre-cut labels come on 8-1/2 x 11"" sheets.   You can download printing templates that will define the edges of the labels (as a table) so you can make your custom design fit the label. Once you’ve created your own design you print the labels with either inkjet or laser printer. In order to add your designs to the template you must have a paid version of adobe acrobat reader or some other PDF editting software.   The special adhesive will stay on while wet and during aging, but can easily be peeled off for reusing bottles. 2-part labels come 4 sets per sheet, 8 sheets per pack, for a total of 32 labels. Blank template for download: PDF (.pdf)  

Read more less

Now you can proudly display your homemade beer with your own custom label!   With these unprinted sheets of adhesive labels you can easily create your own custom beer labels. The pre-cut labels come on 8-1/2 x 11"" sheets. You can download printing templates that will define the edges of the labels (as a table) so you can make your custom design fit the label. Once you’ve created your own design you print the labels with either inkjet or laser printer. The special adhesive will stay on while wet and during aging, but can easily be peeled off for reusing bottles. Beer labels come 6 per sheet, 8 sheets per pack, for a total of 48 labels. Blank templates for download: MS Word (.doc) PDF (.pdf)  

Read more less

Belgian or Sparkling style glass beer bottles High pressure rating to withstand highly carbonated sours, Belgian-style beers, or sparkling wine At 16.9 ounces, this is the perfect bottle size to pour a full pint glass Three cases of 12 bottles are enough to package a 4.75 gallons of finished beer 26mm crown cap finish These high quality 500 ml (16.9 oz) Belgian / Champagne style bottles can be capped with standard crown caps (26mm).  Thicker than standard 12 and 22 oz bottles.  Ideal for lambics and other styles that have higher volumes of CO2.  3 Cases will take 4.75 gallons of beer, roughly the amount needed for a 5 gallon batch. Bottle Specifications: Capacity: 500 ml  Weight: 0.88 lb Height: 10.12 inches Outside Diameter: 2.87 inches Pressure Rating: Up to 4 volumes of carbonation.   Shipping Details:​ Case: 12 Bottles Pallet Layer: 16 Cases  Full Pallet: 64 Cases Weight: 11.75 pounds per case Case dimensions: 12"L x 9-3/8"W x 10-5/8"H

Read more less

Belgian or Sparkling style glass beer bottles High pressure rating to withstand highly carbonated sours, Belgian-style beers, or sparkling wine 750mL capacity makes them ideal of cellaring your most precious creations Two cases of 12 bottles are enough to package just over 4.5 gallons of finished beer 26mm crown cap finish. Can also be corked using a champagne style cork with cage These high-quality Belgian / Champagne style bottles can be capped with standard crown caps (26mm). Bottle Specifications: Capacity: 750 ml  Weight: 1.5 lb Height: 11.9 inches Outside Diameter: 3.3 inches Pressure Rating: Up to 5.5 volumes of carbonation.

Read more less

Traditional 22 oz longneck beer bottles, often referred to as "bombers", take standard crown caps (26 mm).  12 bottles per case, with dividers. These bottles are thicker and darker than most other bottles, offering better protection against UV rays and preventing your beer from becoming lightstruck.  These bottles are used by the likes of Stone, Speakeasy, Drakes, Knee Deep and even Anheuser Busch.   The displacement caused by a 3/8" bottle filler leaves the perfect amount of headspace in your bottle.  Significantly reduce your bottling time by switching from 12 oz bottles to 22 oz bottles. Two cases of this classic beer bottle will house a standard 5 gallon batch of homebrew (you may need an extra bottle or two if you ended up with a full five gallons).  Fits all standard (26 mm) pry-off and universal style crown caps. Don't forget your bottle caps. We stock over 10 different colors and styles of crown caps! Skip labelling your bottles by identifying them with colored crown caps. Bottle Specifications: Capacity: 22 fl. Oz. Weight: 1 5/8 lb Height: 11 inches Outside Diameter: 2.9 inches Pressure Rating: Up to 3 volumes of carbonation.  

Read more less

Traditional 12 oz longneck beer bottles that take standard crown caps (26 mm).  24 bottles per case, with dividers. These bottles are thicker and darker than most other bottles, offering better protection against UV rays and preventing your beer from becoming lightstruck.  These bottles are used by the likes of Stone, Drakes and even the big guys like Anheuser Busch.   The displacement caused by a 3/8" bottle filler (B411) leaves the perfect amount of headspace in your bottle.  Two cases of this classic beer bottle will house a standard 5 gallon batch of homebrew.  Fits all standard (26 mm) pry-off and universal style crown caps. Don't forget your bottle caps. We stock over 10 different colors and styles of crown caps! Skip labelling your bottles by identifying them with colored crown caps. Bottle Specifications: Capacity: 12 fl Oz Weight: 0.425 lb Height: 9 inches Outside Diameter: 2.4 inches Pressure Rating: Up to 3 volumes of carbonation.  

Read more less

#1 Best selling beer faucet! The Perlick Stainless Beer Faucet 630SS is our #1 best selling faucet for two very important reasons. 1) This Perlick Faucet features the revolutionary forward sealing design. Homebrewers are fanatics when it comes to keeping their equipment clean. Beer residue can grow unwanted contaminants, and spoil the taste of your beer. The rear-sealing faucet traps beer inside of its body. There is a pin-hole in the faucet to allow the beer to drain out. This leaves residue, causing the faucet to remain sticky and prone to contamination. The Perlick Faucet, with its forward sealing design, only has beer drain from the short 1" nozzle section. This keeps the operating part of the faucet clean so it will function smoothly (even when it was not cleaned between uses) and greatly reduces the chance of contamination. 2) Stainless Steel construction. It goes without saying that Stainless Steel is the metal you want touching your beer. It has the structural integrity, and durability to last a lifetime. Old-school faucets are made of chrome-plated brass. Eventually, the chrome wears off, exposing the brass. The beer can then pit the brass, leaving nooks and crannies where bacteria can grow. This can cause an off flavor in your beer. Both of these features prevent the faucet from malfunctioning and from adding off flavors to your beer. What more could a serious homebrewer want?

Read more less

Beer Faucet Adapter (w/o Collar)

Read more less

Also called a faucet positioner because it angles big tap handles from touching the wall or refrigerator. Installs on top of beer faucet lever and then the tap handle thread into this bonnet angler. Made from chrome plated brass.

Read more less

The classy way to say "Don't you dare drink my beer!" Do you have a draft system and live with either teenage kids or thirsty roomates? This can potentially be a beer draining arrangement. When you leave for the weekend, stop the flow with a faucet lock. A quick easy locking system that attaches directly to the faucet. Please note - this lock will not work with Perlick 650SS, 630SS or Intertap faucets. For Perlick faucets, please see D1234.

Read more less

The first washer of a two part set that is used to allow motion of lever. Soft black material.

Read more less

Lever for faucet. Black knob screws onto this piece. They will often break if they become stuck and too much force is applied.

Read more less

The nut that attaches faucet to shank.

Read more less