Products

Speidel’s FD-DF Red Wine Fermentation Tank integrates Air Pulse technology directly into your fermentation tank without the need for additional equipment. Increasingly, today’s research is indicating that there are a lot of benefits to controlled oxygen contact during red wine fermentation. Previously considered Public Enemy #1 in the winery, oxygen is now being specifically introduced to the fermenting wine at certain phases. To make this process easier and more approachable, and to eliminate the need for exterior equipment, Speidel developed their FD-DF tank. The tanks is equipped with a set of 4 programmable air-injection nozzles with inline check valves, for total control on the part of the winemaker. Duration of and interval between air injections can be controlled, as well as the inlet pressure. The incoming air can be used to break up and flush CO2 from the cap, causing it to fall back into the fermenting juice for better extraction in addition to helping drive tannin complexing reactions and ensuring healthy ferments to reduce instances of slow or sluggish fermentation. Must Discharge: Automatic, motorized must-discharge arms with gate-style opening allows for fine netering of how fast you allow must to flow out of the tank. Especially useful with thin musts. Must-Discharge motor requires 380V, 3-phase power. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Speidel recommends an accumulation tank for the compressor that can store 1000L or air compressed to 6 bar (265 gal at 90 psi) Speidel recommends that either the compressor natively outputs a filtered, oil-free air or that the compressed air be conditioned before entering the nozzles and tank/must. As filters, Speidel recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent.

Read more less

The age-old, and still practiced, process of manual punch down is now modernized, automated and brought to a larger scale thanks to Speidel! Now th eFD-IT tank improves on the original Pneumatic Punchdown system by moving the pneumaitc piston inside the tank, accomodating wineries with ceiling height restrictions and allowing for tanks to be used to process much smaller lots of must (as little as 40% of full tank capacity!) This simple but effective system features an external  pneumatic cylinder which drives the punching assembly. During the downward stroke the folding stainless punching wings lay flat against the top of the pommace cap and push the solids back into the fermenting wine. On the upward stroke of the cycle the wings set at angle which induces the wings to rotate about 30 degrees, position themselves over a fresh segment of the cap, and the cycle then repeats itself. The whole cap can be punched in as little as 5-6 punch cycles—about 15 minutes! The duration of time that the tank performs punch downs, and the interval of time between them, are adjustable depending on your individual vineyard, vintage and winemaking style. Must Discharge: Automatic, motorized must-discharge arms with hinged door opening. Must-Discharge motor requires 380V, 3-phase power. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Tank ceiling is reinforced to withstand the punchdown forces. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Integrated 50mm (2") pumpover piping with 2" Tri-Clamp connection Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Compressor should be able to provide 500L/min at 6 bar pressure with a minimum of 90L tank capacity (17.7 CFM at 87 psi with a 24 gallon tank). Speidel recommends that the compressed air be conditioned before entering the pneumatic cylinder and recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent. Air Consumption per punch cycle: Immersion Depth Air Consumption 1000 mm 12.3 liters 1250 mm 15.3 liters 1500 mm 18.3 liters 1750 mm 21.4 liters  

Read more less

The age-old, and still practiced, process of manual punch down is now modernized, automated and brought to a larger scale thanks to Speidel! Now th eFD-IT tank improves on the original Pneumatic Punchdown system by moving the pneumaitc piston inside the tank, accomodating wineries with ceiling height restrictions and allowing for tanks to be used to process much smaller lots of must (as little as 40% of full tank capacity!) This simple but effective system features an external  pneumatic cylinder which drives the punching assembly. During the downward stroke the folding stainless punching wings lay flat against the top of the pommace cap and push the solids back into the fermenting wine. On the upward stroke of the cycle the wings set at angle which induces the wings to rotate about 30 degrees, position themselves over a fresh segment of the cap, and the cycle then repeats itself. The whole cap can be punched in as little as 5-6 punch cycles—about 15 minutes! The duration of time that the tank performs punch downs, and the interval of time between them, are adjustable depending on your individual vineyard, vintage and winemaking style. Must Discharge: Automatic, motorized must-discharge arms with gate-style opening allows for fine netering of how fast you allow must to flow out of the tank. Especially useful with thin musts. Must-Discharge motor requires 380V, 3-phase power. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Tank ceiling is reinforced to withstand the punchdown forces. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Integrated 50mm (2") pumpover piping with 2" Tri-Clamp connection Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Compressor should be able to provide 500L/min at 6 bar pressure with a minimum of 90L tank capacity (17.7 CFM at 87 psi with a 24 gallon tank). Speidel recommends that the compressed air be conditioned before entering the pneumatic cylinder and recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent. Air Consumption per punch cycle: Immersion Depth Air Consumption 1000 mm 12.3 liters 1250 mm 15.3 liters 1500 mm 18.3 liters 1750 mm 21.4 liters  

Read more less

A simple and robust red fermentation tank based on the Pumpover style of cap management, with a twist. Instead of standard pumpover flooding, this tank is used in a partial-delestage technique where approxiamtely half the fermenting juice is transferred out of the tank once a cap has formed. As the juice is pumped out and the cap descends through the tank, offset horizontal stainless bars that are welded in place within the tank cause the cap to naturally break up. Then the removed juice is pumped back in through the external piping and through the spinning flooder head in the tank ceiling, wetting and re-submerging the cap! Must Discharge: Automatic, motorized must-discharge arms with hinged door opening. Must-Discharge motor requires 380V, 3-phase power. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Integrated 50mm (2") pumpover piping with 2" Tri-Clamp connection and rotating juice flooder Horizontal offset cap-breaking bars  

Read more less

A simple and robust red fermentation tank based on the Pumpover style of cap management, with a twist. Instead of standard pumpover flooding, this tank is used in a partial-delestage technique where approxiamtely half the fermenting juice is transferred out of the tank once a cap has formed. As the juice is pumped out and the cap descends through the tank, offset horizontal stainless bars that are welded in place within the tank cause the cap to naturally break up. Then the removed juice is pumped back in through the external piping and through the spinning flooder head in the tank ceiling, wetting and re-submerging the cap! Must Discharge: Automatic, motorized must-discharge arms with gate-style opening allows for fine netering of how fast you allow must to flow out of the tank. Especially useful with thin musts. Must-Discharge motor requires 380V, 3-phase power. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Integrated 50mm (2") pumpover piping with 2" Tri-Clamp connection and rotating juice flooder Horizontal offset cap-breaking bars  

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be customized with a wide array of add-on features, and can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be customized with a wide array of add-on features, and can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters   Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be customized with a wide array of add-on features, and can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel's SD-MGRL Tanks bring high tech fermentation solutions to wineries with restricted ceiling heights. The horizontal red wine fermenter is equipped with a slow-moving center shaft with mixing arms attached to it, which effectively break up and re-submerge the cap after just a few rotations. The duration of and interval between immersion operations is programmable to suit the needs of your different vineyards and vintages as well as your individual winemaking style. The mixing arms are slanted forward which pushes must forward and promotes complete emptying of the tank once fermentation is complete through the 125,mm (5") drain valve.   Key Features: Tank entirely in AISI304 stainless steel. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow 42x32 cm (16.5x12.5 in) Oval Racking Door Included NW 10 DIN stainless thermowell with analog bi-metal thermometer insert Included NW 20 DIN stainless sample valve 125 mm (5") threaded drain port, 2” Tri-Clamp racking outlet. Stainless steel electronic control box 380V 3-phase gear-reduced mixing motor turns at 3 rpm for cap management and at 6 rpm for must evacuation.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be customized with a wide array of add-on features, and can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be customized with a wide array of add-on features, and can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters   Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel’s FD-DF Red Wine Fermentation Tank integrates Air Pulse technology directly into your fermentation tank without the need for additional equipment. Increasingly, today’s research is indicating that there are a lot of benefits to controlled oxygen contact during red wine fermentation. Previously considered Public Enemy #1 in the winery, oxygen is now being specifically introduced to the fermenting wine at certain phases. To make this process easier and more approachable, and to eliminate the need for exterior equipment, Speidel developed their FD-DF tank. The tanks is equipped with a set of 4 programmable air-injection nozzles with inline check valves, for total control on the part of the winemaker. Duration of and interval between air injections can be controlled, as well as the inlet pressure. The incoming air can be used to break up and flush CO2 from the cap, causing it to fall back into the fermenting juice for better extraction in addition to helping drive tannin complexing reactions and ensuring healthy ferments to reduce instances of slow or sluggish fermentation. Must Discharge: Forward sloped Fermentation Manway with gate-style opening allows of fine netering of how fast you allow must to flow out of the tank. Especially useful with thin musts. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Speidel recommends an accumulation tank for the compressor that can store 1000L or air compressed to 6 bar (265 gal at 90 psi) Speidel recommends that either the compressor natively outputs a filtered, oil-free air or that the compressed air be conditioned before entering the nozzles and tank/must. As filters, Speidel recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent.

Read more less

The age-old, and still practiced, process of manual punch down is now modernized, automated and brought to a larger scale thanks to Speidel! Now th eFD-IT tank improves on the original Pneumatic Punchdown system by moving the pneumaitc piston inside the tank, accomodating wineries with ceiling height restrictions and allowing for tanks to be used to process much smaller lots of must (as little as 40% of full tank capacity!) This simple but effective system features an external  pneumatic cylinder which drives the punching assembly. During the downward stroke the folding stainless punching wings lay flat against the top of the pommace cap and push the solids back into the fermenting wine. On the upward stroke of the cycle the wings set at angle which induces the wings to rotate about 30 degrees, position themselves over a fresh segment of the cap, and the cycle then repeats itself. The whole cap can be punched in as little as 5-6 punch cycles—about 15 minutes! The duration of time that the tank performs punch downs, and the interval of time between them, are adjustable depending on your individual vineyard, vintage and winemaking style. Must Discharge: Forward sloped Fermentation Manway with hinged door opening. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Tank ceiling is reinforced to withstand the punchdown forces. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Integrated 50mm (2") pumpover piping with 2" Tri-Clamp connection Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Compressor should be able to provide 500L/min at 6 bar pressure with a minimum of 90L tank capacity (17.7 CFM at 87 psi with a 24 gallon tank). Speidel recommends that the compressed air be conditioned before entering the pneumatic cylinder and recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent. Air Consumption per punch cycle: Immersion Depth Air Consumption 1000 mm 12.3 liters 1250 mm 15.3 liters 1500 mm 18.3 liters 1750 mm 21.4 liters  

Read more less

The age-old, and still practiced, process of manual punch down is now modernized, automated and brought to a larger scale thanks to Speidel! Now th eFD-IT tank improves on the original Pneumatic Punchdown system by moving the pneumaitc piston inside the tank, accomodating wineries with ceiling height restrictions and allowing for tanks to be used to process much smaller lots of must (as little as 40% of full tank capacity!) This simple but effective system features an external  pneumatic cylinder which drives the punching assembly. During the downward stroke the folding stainless punching wings lay flat against the top of the pommace cap and push the solids back into the fermenting wine. On the upward stroke of the cycle the wings set at angle which induces the wings to rotate about 30 degrees, position themselves over a fresh segment of the cap, and the cycle then repeats itself. The whole cap can be punched in as little as 5-6 punch cycles—about 15 minutes! The duration of time that the tank performs punch downs, and the interval of time between them, are adjustable depending on your individual vineyard, vintage and winemaking style. Must Discharge: Forward sloped Fermentation Manway with gate-style opening allows of fine netering of how fast you allow must to flow out of the tank. Especially useful with thin musts. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Tank ceiling is reinforced to withstand the punchdown forces. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Integrated 50mm (2") pumpover piping with 2" Tri-Clamp connection Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Compressor should be able to provide 500L/min at 6 bar pressure with a minimum of 90L tank capacity (17.7 CFM at 87 psi with a 24 gallon tank). Speidel recommends that the compressed air be conditioned before entering the pneumatic cylinder and recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent. Air Consumption per punch cycle: Immersion Depth Air Consumption 1000 mm 12.3 liters 1250 mm 15.3 liters 1500 mm 18.3 liters 1750 mm 21.4 liters  

Read more less

The age-old, and still practiced, process of manual punch down is now modernized, automated and brought to a larger scale thanks to Speidel! This simple but effective system features an external  pneumatic cylinder which drives the punching assembly. During the downward stroke the folding stainless punching wings lay flat against the top of the pommace cap and push the solids back into the fermenting wine. On the upward stroke of the cycle the wings set at angle which induces the wings to rotate about 30 degrees, position themselves over a fresh segment of the cap, and the cycle then repeats itself. The whole cap can be punched in as little as 5-6 punch cycles—about 15 minutes! The duration of time that the tank performs punch downs, and the interval of time between them, are adjustable depending on your individual vineyard, vintage and winemaking style. Must Discharge: Forward sloped Fermentation Manway with hinged door opening Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Tank ceiling is reinforced to withstand the punchdown forces. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN  stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Compressor should be able to provide 500L/min at 6 bar pressure with a minimum of 90L tank capacity (17.7 CFM at 87 psi with a 24 gallon tank). Speidel recommends that the compressed air be conditioned before entering the pneumatic cylinder and recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent. Air Consumption per punch cycle: Immersion Depth Air Consumption 1000 mm 12.3 liters 1250 mm 15.3 liters 1500 mm 18.3 liters 1750 mm 21.4 liters  

Read more less

The age-old, and still practiced, process of manual punch down is now modernized, automated and brought to a larger scale thanks to Speidel! This simple but effective system features an external  pneumatic cylinder which drives the punching assembly. During the downward stroke the folding stainless punching wings lay flat against the top of the pommace cap and push the solids back into the fermenting wine. On the upward stroke of the cycle the wings set at angle which induces the wings to rotate about 30 degrees, position themselves over a fresh segment of the cap, and the cycle then repeats itself. The whole cap can be punched in as little as 5-6 punch cycles—about 15 minutes! The duration of time that the tank performs punch downs, and the interval of time between them, are adjustable depending on your individual vineyard, vintage and winemaking style. Must Discharge: Forward sloped Fermentation Manway with gate-style opening allows of fine netering  of how fast you allow must to flow out of the tank. Especially useful with thin musts. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Tank ceiling is reinforced to withstand the punchdown forces. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Compressor should be able to provide 500L/min at 6 bar pressure with a minimum of 90L tank capacity (17.7 CFM at 87 psi with a 24 gallon tank). Speidel recommends that the compressed air be conditioned before entering the pneumatic cylinder and recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent. Air Consumption per punch cycle: Immersion Depth Air Consumption 1000 mm 12.3 liters 1250 mm 15.3 liters 1500 mm 18.3 liters 1750 mm 21.4 liters  

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be customized with a wide array of add-on features, and can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be customized with a wide array of add-on features, and can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters   Click Here for more information on the key features of all Speidel Tanks.

Read more less

The age-old, and still practiced, process of manual punch down is now modernized, automated and brought to a larger scale thanks to Speidel! This simple but effective system features an external  pneumatic cylinder which drives the punching assembly. During the downward stroke the folding stainless punching wings lay flat against the top of the pommace cap and push the solids back into the fermenting wine. On the upward stroke of the cycle the wings set at angle which induces the wings to rotate about 30 degrees, position themselves over a fresh segment of the cap, and the cycle then repeats itself. The whole cap can be punched in as little as 5-6 punch cycles—about 15 minutes! The duration of time that the tank performs punch downs, and the interval of time between them, are adjustable depending on your individual vineyard, vintage and winemaking style. Must Discharge: Automatic, motorized must-discharge arms with hinged door opening. Must-Discharge motor requires 380V, 3-phase power. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Tank ceiling is reinforced to withstand the punchdown forces. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Compressor should be able to provide 500L/min at 6 bar pressure with a minimum of 90L tank capacity (17.7 CFM at 87 psi with a 24 gallon tank). Speidel recommends that the compressed air be conditioned before entering the pneumatic cylinder and recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent. Air Consumption per punch cycle: Immersion Depth Air Consumption 1000 mm 12.3 liters 1250 mm 15.3 liters 1500 mm 18.3 liters 1750 mm 21.4 liters  

Read more less

The age-old, and still practiced, process of manual punch down is now modernized, automated and brought to a larger scale thanks to Speidel! This simple but effective system features an external  pneumatic cylinder which drives the punching assembly. During the downward stroke the folding stainless punching wings lay flat against the top of the pommace cap and push the solids back into the fermenting wine. On the upward stroke of the cycle the wings set at angle which induces the wings to rotate about 30 degrees, position themselves over a fresh segment of the cap, and the cycle then repeats itself. The whole cap can be punched in as little as 5-6 punch cycles—about 15 minutes! The duration of time that the tank performs punch downs, and the interval of time between them, are adjustable depending on your individual vineyard, vintage and winemaking style. Must Discharge: Automatic, motorized must-discharge arms with gate-style opening allows for fine netering of how fast you allow must to flow out of the tank. Especially useful with thin musts. Must-Discharge motor requires 380V, 3-phase power. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Tank ceiling is reinforced to withstand the punchdown forces. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Compressor should be able to provide 500L/min at 6 bar pressure with a minimum of 90L tank capacity (17.7 CFM at 87 psi with a 24 gallon tank). Speidel recommends that the compressed air be conditioned before entering the pneumatic cylinder and recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent. Air Consumption per punch cycle: Immersion Depth Air Consumption 1000 mm 12.3 liters 1250 mm 15.3 liters 1500 mm 18.3 liters 1750 mm 21.4 liters  

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be customized with a wide array of add-on features, and can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters Click Here for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be customized with a wide array of add-on features, and can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time.   Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters   Click Here for more information on the key features of all Speidel Tanks.

Read more less

The FO Variable Volume tank is Speidel's flagship Variable Volume tank for storage. Available in 28 different capacities from 1,100L up to over 15,000L. Each tank has multiple cooling jacket styles and a host of other optional add-ons available. Truly customizable to your winery's needs! Key Features Available in 28 sizes covering 6 different tank diameters from 1,100L to 15,200L (larger tanks available with special shipping arrangements) 1,100L & 1,650L Tanks equipped with 1.5" TC racking and drainage ports. All other tanks equipped with 2" TC. Larger fittings available by request Reinforced racking ports prevent tank wall flex and can support the weight of a tank mixer. All tanks have welded-on mounting points for lid lifting arms. Tanks from 1,650L include a lifting arm; from 2,200L up the arm is winch-operated Click Here for more information on the key features of all Speidel Tanks. Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.    

Read more less

The FO-M tank from Speidel is very similar to the the standard FO style variable volume storage tank. The FO-M tank, however, has been specially altered to make it more useful as a fermentation tank, and comes pre-fitted with the most standard features equipped on tanks used for red fermentations. And they have the same degree of flexibility and customization available as the standard FO style tank, but offer an easy starting point and cost savings for tanks destined for red fermentation. And don't miss out on Spediel's Mobile Must Plunger, which makes punch downs fast, easy and automatic! Key Features Available in 28 sizes covering 6 different tank diameters from 1,100L to 15,200L Tank is equipped with rectangular manway for must discharge. Legs elevated to 52cm height for easier must discharge. Can be extended up to 80cm to accommodate a macro bin under the manway. Bottom drain is rotated to just in front of the left tank leg so it's out of the way of must receptacle. 1,100L & 1,600L Tanks equipped with 1.5" TC racking and drainage ports. All other tanks equipped with 2" TC. Larger fittings available by request Reinforced racking ports prevent tank wall flex and can support the weight of a tank mixer. All tanks include a lifting arm. Mobile, forkliftable Pneumatic Must Plunger available to go with these tanks! Click Here for more information on the key features of all Speidel Tanks. Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.    

Read more less