Beer Making

Replacement Wire Malt Pipe Support for 35L BrewZilla. Made from 304 stainless steel. This is the "Gen 2" version of the wire support ring. It has been slightly modified from the previous version to be compatible with all generations of BrewZillas and DigiBoils. KegLand Part Number: KL88020

Read more less

Specifically designed for maximum strength and rigidity. This redesigned top screen features a hole for the probe of the RAPT Bluetooth Thermometer (coming soon) for monitoring and controlling your BrewZilla Gen 4. KegLand Part Number: KL27366  

Read more less

This false bottom is specifically designed for the Gen 4 35L BrewZilla. On this model the ball valve tap was relocated underneath the unit, allowing for a super low profile false bottom that molds itself to the concave bottom of the BrewZilla. This also allowed for a larger malt pipe for bigger grain bills and provides a filter for protecting the easy access pump. It is not suitable for DigiBoils or Gen 3.1.1 or older BrewZillas, as those models do not have a concave bottom. Includes 2x Eye Bolt Assemblies. KegLand Part Number: KL27304  

Read more less

Replacement RAPT Controller for 35L Gen 4 BrewZillas. Compatible with all Gen 4 models. This will not work with BrewZilla Gen 3.1.1 models or older. It is also not suitable for DigiBoil units. Please refer to the instruction manual on adjusting the controller between the Gen 4 units. There is a mechanical toggle switch on the back of the board that will need to be adjusted. KegLand Part Number: KL20305  

Read more less

Replacement silicone seal for the 35L size Boiler Extension Kit. KegLand Part Number: KL22576

Read more less

Replacement silicone seal for the 65L size Boiler Extension Kit. KegLand Part Number: KL22866

Read more less

Shutoff check valves can be used in multiple gas applications. Commonly added to CO2 regulators or manifolds to protect your equipment from back flow. 1/4" NPT check valve with 1/4" barb. Use with 1/4" or 5/16" ID gas line.

Read more less

Shutoff check valves can be used in multiple gas applications. Commonly added to CO2 regulators or manifolds to protect your equipment from back flow. 1/4" NPT check valve with 1/4" barb. Use with 3/16" or 1/4" ID gas line.

Read more less

Stainless steel barb adapter for 1/4" female pipe thread connections. For use with 3/16" or 1/4" ID tubing. Pack of 2.

Read more less

Adapt 1/4" male pipe thread to 1/4" male flare thread, making any 1/4" FPT fitting compatible with flare fittings or flare threaded Duotight fittings. Made from chrome plated brass.

Read more less

Replacement wrenches that comes included with the Cannular Can Seamer. KegLand Part Number: KL13192

Read more less

Replacement Operation Switch (Momentary Switch) for Cannular can seamer. This switch is only compatible with the Cannular Pro Semi-Auto unit. NOTE: the switch might be yellow or blue. You can tell the Operation Switch from the Power Switch by testing the button. The Operation Switch can be depressed/pushed in while the Power Switch will only click when pressed. KegLand Part Number: KL16445

Read more less

This flat lid with pre-drilled holes allows you to easily add a Temp Twister Cooling Coil to your 35L Bucket Buddy fermenter. It also has holes for your stopper & airlock (included with the Bucket Buddy) as well as a Thermowell so you can control the circulation of cooling solution with a Temperature Controller. The lid is also compatible with 65L BrewZillas and DigiBoils. If you're fermenting in the Bucket Buddy with built-in heating element, we recommend plugging the unit into the heating outlet of your temperature controller and leaving the power switch turned on. This will allow the temp controller to provide power to the unit only when heating is needed and it will cut the power as soon as you're back to your set temperature. Using the Bucket Buddy's controller to maintain the heating set temp and using a separate controller to maintain the cooling may result in heating and cooling cycling at the same time. NOTE: The pre-drilled holes are meant for specific sizes of Duotight bulkheads and the stopper included with the Bucket Buddy fermenter. All holes need to be occupied in order to protect your fermentation from outside contaminants. Depending on the placement of the Temp Twister, you might need to shorten the inlet/outlet tubes on the outside of the fermenter using a Pipe Cutter. Lid only. Other accessories must be purchased separately. You Will Also Need: Temp Twister Cooling Coil FermZilla Thermowell Temperature Controller KegLand Part Number: KL28110

Read more less

This flat lid with pre-drilled holes allows you to easily add a Temp Twister Cooling Coil to your 35L Bucket Buddy fermenter. It also has holes for your stopper & airlock (included with the Bucket Buddy) as well as a Thermowell so you can control the circulation of cooling solution with a Temperature Controller. The lid is also compatible with 35L BrewZillas and DigiBoils. If you're fermenting in the Bucket Buddy with built-in heating element, we recommend plugging the unit into the heating outlet of your temperature controller and leaving the power switch turned on. This will allow the temp controller to provide power to the unit only when heating is needed and it will cut the power as soon as you're back to your set temperature. Using the Bucket Buddy's controller to maintain the heating set temp and using a separate controller to maintain the cooling may result in heating and cooling cycling at the same time. NOTE: The pre-drilled holes are meant for specific sizes of Duotight bulkheads and the stopper included with the Bucket Buddy fermenter. All holes need to be occupied in order to protect your fermentation from outside contaminants. Depending on the placement of the Temp Twister, you might need to shorten the inlet/outlet tubes on the outside of the fermenter using a Pipe Cutter. Lid only. Other accessories must be purchased separately. You Will Also Need: Temp Twister Cooling Coil FermZilla Thermowell Temperature Controller KegLand Part Number: KL28103

Read more less

The CMBecker International Inline Flow Control 10mm Barb is necessary for those looking to use tubing that has an inner diameter of 3/8". It is slightly smaller than 1/2", but it will fit a 1/2" ID Hose if properly clamped. Use with CMBecker In-Line Flow Control Compensator Stainless steel nipple, only stainless steel touches your beverage Works with CMBecker International shanks. Includes CMBecker beer nut The size is 10mm which is between 1/2" and 3/8". When using with 3/8" hose you may need to slightly heat hose (using hot water) to stretch hose over barb (this is how we do it!) When using with 1/2" it will be loose, but we have used it with syphon hose and thicker high heat (EJ beverage or silicone) hose. Just make sure you clamp it properly to get a good seal. This will not work with a standard shank, it works with CMBecker shanks

Read more less

The CMBecker Inline Flow Control 7mm Barb is necessary for those looking to use tubing that has an inner diameter of 5/16 or 3/8" Use with CMBecker In-Line Flow Control Compensator Stainless steel nipple, only stainless steel touches your beverage Works with CMBecker International shanks. Includes CMBecker beer nut The size is 7mm which is slightly wider than 1/4" at 0.27" This will not work with a standard shank, it works with CMBecker shanks.

Read more less

The CMBecker Inline Flow Control 4mm Barb is necessary for those looking to use tubing that has an inner diameter of 3/16" Use with CMBecker In-Line Flow Control Compensator Stainless steel nipple, only stainless steel touches your beverage Works with CMBecker International shanks. Includes CMBecker beer nut The size is 4mm. When using with 3/16" hose you may need to slightly heat hose (using hot water) to stretch hose over barb (this is how we do it!) Just make sure you clamp it properly to get a good seal This will not work with a standard shank, it works with CMBecker shanks. These seal at two places and do not have a flat end (see photo)

Read more less

Replacement seal for barbed or flareed stainless ball lock quick disconnects from KegLand. Compatible with KEG732, KEG734, KEG745, & KEG746.  

Read more less

Replacement Actuator Pin / Thumb Screw Assembly for KegLand Core 360 Mini CO2 Regulator. KegLand Part Number: KL20039

Read more less

Replacement Duotight Barb for KegLand Core 360 Mini CO2 Regulator. KegLand Part Number: KL22835

Read more less

Replacement FFL Outlet for KegLand Core 360 Mini CO2 Regulator KegLand Part Number: KL22828

Read more less

Contains the o-rings for the piston, the red inlet washer, MK4 seat assembly o-ring, 2 x barb MFL outlet o-rings and a thumb screw o-ring. For instructions on replacing the seals and/or general maintenance please refer to the product manual below. KegLand Part Number: KL12584

Read more less

This extra-long drip tray is well-suited for the KOMOS Double-Wide kegerator and home bar countertops. Made from stainless steel with a removable grill. Good for up to 8 horizontally mounted draft faucets. Features: Removable grill Made from stainless steel 29.5" L x 6.7" W x 0.9" D  

Read more less

Asco Root™ is a granular slow release extract of cold water seaweed (Ascophyllum nodosum). It greatly helps to aid in root growth and set, stress tolerance, and overall plant health while providing a strong potassium source. It has shown exceptional yield increases in field trials, and provides a great head start to help first year rhizome planting. You will receive a bag to cover the volume need of 5 rhizomes, and it should be planted in the hole with your rhizomes when planting.  

Read more less