Dozens of fittings and valves for almost any winemaking application.
Fittings & Valves
Shop By Collection
-
Stainless - 1/4" Ball Valve Full Port
Our Ball Valves will last for years. Easy to clean. High grade 304-stainless made to last. 1/4" FPT on input and output side. TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and two gaskets that form the seal when closed. Here at MoreFlavor! we think this ball valve is actually easier to clean than 3-piece ball valves (such as our H602D).
$16.49
-
Stainless Nipple - 3/8"x1" Threaded (Close)
These are typically used for connecting Ball Valves to couplers welded into tanks. “Close” thread means there is no space between the opposing threads
$3.29
-
Stainless Coupler 3/8" FPT x 1/2" FPT
Stainless Reducing Coupler 3/8" FPT x 1/2" FPT
$5.49
-
Stainless Half Coupler - 3/8"
Half Coupler with 3/8" Female Pipe Thread. Half couplers have thread for insertion from one side only.
$3.99
-
Stainless Half Coupler - 1/2"
Half Coupler with 1/2" Female Pipe Thread. Half couplers have thread for insertion from one side only. 304 stainless. Weld into place. You will need to punch a 7/8" hole to install.
$5.49
-
Stainless Half Coupler 1"
Stainless Half Coupler with 1" Female Pipe Thread. Half couplers have thread for insertion from one side only.
$5.49
-
Compression Fitting - 12.7 mm to 1/2 in. BSP
These compression fittings are the most common type to be used with immersion chillers on the market today. We highly recommend using these fittings on any and all immersion / ice bucket chillers to optimize the ability to quicky disconnect the liquid hosing for storage and ease of cleaning. The industry standard fittings are Camlocks which can be found here. These fittings have a pressure rating of 4500psi. Instructions: Tighen the fitting up finger tight. Mark the female and male threaded pars with a texter or marker. Further this fitting 1 and 1/4 turns to ensure correct compression has been achieved. KegLand Part Number: KL02004
$9.89
-
Stainless Plug - 1/2 in. BSPP
1/2" male BSPP stainless steel plug. Hex head design for easy installation or removal with a wrench. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" and 3/4" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL06408
$2.79
-
Stainless Lock Nut - 3/4 in. BSPP
Stainless Lock Nut. 3/4 in. Female BSPP. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" and 3/4" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL06538
$3.29
-
Stainless Coupler - 1/2 in. BSPP x 3/8 in. BSPP
Stainless steel coupler or "reducing socket". 1/2" BSPP x 3/8" BSPP. Made from stainless steel. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" and 3/4" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL10580
$3.89
-
Stainless Elbow - 1/2 in. Male BSP x 1/2 in. Female BSP
Male to female elbow. 1/2" BSP. Made from 304 grade stainless steel. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" and 3/4" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL06620
$5.49
-
KOMOS® | Stainless Barb | 1/4 in. MPT x 5/16 in. Barb | 2-Pack
Stainless steel barb adapter for 1/4" femaile pipe thread connections. For use with 1/4" or 5/16" ID tubing. Pack of 2.
$7.69
-
Brass - 1/2 in. MPT x 1/4 in. FPT Bushing
Brass - 1/2'' MPT x 1/4" FPT Bushing
$2.99
-
$3.29
-
Brass - 3/8" MPT x 1/2" Barb
Brass - 3/8" MPT x 1/2" Barb
$3.59
-
Brass Nipple 1/2" Close
Male 1/2" NPT threads on both sides, no space between them
$3.99
-
Flanged Tri-Clamp Gasket | EPDM | 3"
Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections EPDM gaskets are more resistant to acids and caustic chemicals, and don't show signs of wear as quickly as silicone For 3" tri-clamp connections A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both EPDM and Silicone. EPDM gaskets have a more narrow temperature range than silicone gaskets, but they are more resistant to acids and caustic chemicals. For 3" tri-clamp fittings Made from EPDM Temperature rated from -30°F to 300°F KegLand Part Number: KL45216 Example Image: Updated images coming soon. See the video below to check out the flanged gaskets in action.
$2.59
-
Flanged Tri-Clamp Gasket | Silicone | 3"
Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections Silicone gaskets have a wide temperature range and are recommended for hot side applications For 3" tri-clamp connections A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both Silicone and EPDM. Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 3" tri-clamp fittings Made from Silicone Temperature rated from -58°F to 446°F KegLand Part Number: KL44813
$2.59
-
Stainless Tri-Clamp Ferrule | 3" T.C.
3" TC Ferrule is used to weld in a TC connection anywhere you need one! AiSI304 Stainless Steel.
$14.49
-
TC Reducers | 3 in. to 1.5 in.
Tri Clamp adapter that goes from a 3" TC to a 1.5" TC.
$25.95
-
BrewBuilt® Stainless Butterfly Valve | 2" T.C.
The BrewBuilt Butterfly Valve has all the standard advantages you would expect from a butterfly valve in that they are the most sanitary valve, easy to clean and won't trap wort inside. It has a custom polished stainless steel handle which is designed to fit perfectly with the BrewBuilt X-series conical 2" T.C. bottom port.
$99.99
-
Stainless Tri-Clamp | 3 Piece | 3" Clamp
This stainless steel tri-clamp features two hinges and folds into three pieces. Some brewers find this style of clamp easier to work with on large equipment that requires a 3" clamp. Direct replacement part to the clamp included with the FermZilla Tri-Conical fermenter. KegLand Part Number: KL25799
$14.49
-
Stainless Full Coupler - 3/8 in. BSPP
Full Coupler with 3/8" Female BSPP Thread. Full couplers have threads for insertion from both sides. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" and 3/4" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL06484
$2.79
-
Plastic Tubing Joiner | 3/8" x 3/8"
Temperature Range: Nylon: 32° to 140° F Acetal: -40° to 175° F Tubing: Nylon: Use with firm or soft (Durometer 45A-80A) polyurethane rubber or PVC plastic Acetal: Use with firm or soft (Durometer 40A-80A) polyurethane rubber or PVC plastic
$2.99
