Whether you're a professional winery, or are making small batches in your kitchen, hardware parts will be necessary. We offer dozens of hardware parts, from hose clamps to butterfly valves. Any hardware you'll need to make great wine can be found in the categories below!
Wine Making Hardware
Shop By Collection
-
KOMOS® | CO2 Regulator Gasket | Fiber Washer | 4-Pack
This compression style fiber washers are a must if you use regulator that requires a gasket change everytime you change the tank. Comes in a convenient zip lock bag. NOTE: These are not intended for use with the KOMOS CO2 Regulator. For the correct KOMOS Regulator replacement gasket, please see D1089.
$1.69
-
KOMOS® | CO2 Regulator Gasket | Silicone Stem O-Ring | 2-Pack
Silicone regulator stem o-ring. Commonly used on Taprite regulators which have an o-ring located where the regulator stem mates with the CO2 cylinder. Comes in a convenient zip lock bag. NOTE: These are not intended for use with the KOMOS CO2 Regulator. For the correct KOMOS Regulator replacement gasket, please see D1089.
$5.49
-
KOMOS® 25 lb CO2 Tank | Premium Aluminum | New | CGA320 Valve | US DOT Approved
Brand new aluminum 25 lb CO2 tank made from high strength aluminum alloy and high quality CGA320 valves. Because it is made of aluminum rather than steel you can feel confident that it won’t rust. It’s called a 25 lb tank because it holds 25 lbs of compressed (liquified) CO2. 25 lbs of CO2 is enough to dispense about 50x 5-gallon kegs of homebrew. Aluminum tanks are superior to steel because they do not rust. All tanks are shipped empty. To have tanks filled you will want to visit your local welding supply shop. Because you are purchasing a new tank you can choose to either have it filled or to exchange it for a filled tank at your local gas supplier. If you have this tank filled the local gas supplier is responsible for affixing the correct neck label that identifies the gas being put in the cylinder. Tanks should always be stored in an upright position. Features: Made from corrosion resistant, engineered Aluminum Brushed finish Thick, durable cylinder walls 32.5" T x 8 Ø DOT approved New high quality CGA-320 valve Light weight compared to steel tanks
$239.99
-
Duotight Draft Regulator Board | Gas Manifold | 6 Way
Serve beverages at different pressures without the need for multiple CO2 cylinders, dual body regulators, or expensive gas manifolds Feed a single pressure to the gas board from your regulator and then step down the pressure on each Duotight regulator Use one line for serving ales, another for soda or seltzer water, and another for carbonating a freshly filled keg All parts shown are included and snap together quickly thanks to Duotight push-to-connect fittings and rigid plastic joiners Duotight In-Line Regulators feature built-in pressure gauges that read 0-60 PSI and can be swapped out for different ranges if desired The Duotight Draft Regulator Board is a simple and cost-effective solution to serving beer and other beverages on draft at different pressures. With a standard CO2 tank and CO2 regulator, you can feed gas at a single pressure into the regulator board and then fine tune individual pressure settings for each gas line via the Duotight In-Line Regulators. These regulators feature built-in pressure gauges that make adjustments super simple and check valves are included as standard so you never have to worry about back flow into the regulator. This kit includes everything you need to assemble your regulator board and can be customized so the gas inlet is on the right or left side—whichever makes the most sense for your home draft setup. Duotight push-to-connect fittings and the precut rigid joiners make assembly a breeze and only takes 10-15 minutes! The draft board kit comes in two options—with or without shut off valves. These valves offer peace of mind and allow you to shut off gas flow to any line that is not in use. If you ensure that your system has no leaks, they aren't technically needed, and you can always fully tighten your Duotight Regulator adjustment knob for added protection. But that little extra security might help you sleep easier at night! One advantage of choosing no check valves, however, is that it will leave room at the top of the board to label your gas lines. One of the coolest features of the Duotight In-Line Regulator is that the included pressure gauge can be swapped out for different pressure ranges. The standard gauge reads 0-60 PSI, but if you have one line that will always be used for serving Ales, you can swap to a 0-15 PSI gauge that will be a little easier to read and make precise adjustments. There's also a Digital Pressure Gauge available that provides backlit instant reads and is rated from 0-90 PSI. Don't need 6 gas lines? Check out the 4-Way Duotight Draft Regulator Board. Please Note: Full assembly required. The gas board, regulators, and fittings will arrive loose. Please see our instructions and assembly video below. Stepping Down Pressure The ideal regulation scenario occurs when the inline regulator steps down the output pressure to at least 10 PSI less than the inlet pressure. For example, if the inlet pressure is 30 PSI, the regulator effectively manages a range from 0–20 PSI on the output side ensuring optimal performance and stability. Ideal regulation scenario (10 PSI less than inlet pressure) Example of 30 PSI inlet translating to 0–20 PSI output Kit Includes: 6-Output Gas Board (6) Duotight In-Line Regulators (6) Duotight Check Valves (6) Duotight Shut Off Valves (if selected above) (5) Duotight Tees (1) Duotight Elbow (23) Rigid Plastic Joiners NOTE: All Duotight fittings and rigid plastic joiners come as 8mm OD. Mounting hardware is included for the regulators but not for mounting the board itself to a wall or the inside of your kegerator/keezer. If you select the option without shutoff valves, you will be left with some spare joiners after assembly.
$142.99
-
KOMOS® | Ball Lock Keg | Stainless Steel Corny Keg | 5 gal.
The KOMOS Homebrew keg is the perfect option for beer, cold brew coffee, kombucha, cider, or any other beverage you want to serve under pressure. Built in an ISO 9001-certified facility and made from beverage-grade 304 stainless steel with robotically welded seams. Features a single steel handle and rubber boot at the bottom, so they're easy to move around and won't damage floors, and they can be stacked on top of other homebrew kegs with a rubber top. The lid's pull ring PRV provides both manual and automatic pressure relief. Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams Single Ergonomic Steel Handle Rubber Boot Bottom ISO9001 Quality Assurance NSF Approved Made from 304 Stainless Steel 25.25" H x 8.75" D
$119.99
-
Corny Keg Lid O-Ring | EPDM | Corny Keg Part
Round EPDM O-rings for Cornelius keg lids.
$3.29
-
Stainless Steel Hoffman Clamp | Flow Control Pinch Clamp for Flexible Tubing | 30mm | 1"
Hoffman Clamps, or screw compressor clamps, are used to control the flow in flexible tubing. The clamp has a machined adjustment screw to permit accurate regulation of the flow. All corners are rounded to prevent cutting of the tubing. This can be particularly useful when regulating the flow of sparge water, collecting sweet wort from your mash tun, or liquid management applications of a still. Max Tubing OD: 30mm / 1.18" KegLand Part Numbers: KL37891
$6.59
-
EVABarrier Double Wall Draft Tubing | LightShield Black | 3 mm ID x 6.35 mm OD
Easily identify gas and beverage lines with color-coded options—LightShield Black for beverages, Transparent Red for gas EVABarrier's double-walled design with a proprietary inner polymer significantly reduces oxidation and CO2 loss, keeping your beer fresher for longer The ultra-smooth, nearly impermeable inner surface of the tubing prevents bacteria and microbes from adhering, ensuring cleaner beer lines The stiff yet pliable EVA outer barrier makes the tubing kink-resistant and ideal for use with push-in fittings like Duotight and John Guest 3 mm ID size is perfect for mobile draft applications where only a short 3.2 ft. beverage line is needed Easily identify your gas and beverage lines with color-coded draft tubing. LightShield Black EVABarrier is recommended for beverage lines while using Transparent Red for your gas lines, saving you a headache when your draft lines inevitably get tangled up in your draft system. LightShield Black also works perfectly for hydroponic systems as it will block UV and discourage algae growth. If you're looking for a high-quality draft tubing to take your system into the 21st century, EVABarrier is the clear choice. This double walled tubing offers superior protection against oxidation, CO2 loss and microbial growth. Plus, it's BPA and PVC free! EVA tubing is the future of draft line for professional applications, and now you can rig up your home system with the same first-class tubing. The 3 mm (5/32") ID size is perfect for mobile draft applications or home draft systems where only a short beverage line is needed. Lengths of 3.2 ft. per line are all that you'll need for adequate flow resistance. Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest, and other push-in fittings. Inner Barrier The inner barrier is made from a proprietary polymer that acts as an excellent gas barrier. You can rest assured that your beer will be better protected from oxygen exposure, as well as CO2 loss. Your beer will stay fresher for longer and not loose carbonation like with other draft line. With other beverage line, you may notice that beer sitting in the line for an extended period will start to taste flat and/or oxidized. EVA Barrier tubing is unquestionably better in this regard and you will notice a significantly improved freshness of your beer, especially if it's been sitting in the lines for a while. Due to the high density and smooth nature of the EVABarrier inner wall, the internal surface of the tubing is remarkably smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing. Just another way EVABarrier is looking out for you and your beer! Direct Connect to Ball Lock Kegs This tubing works seamlessly with Duotight Gas In and Bev Out Ball Lock QDs which allow you to connect your draft lines directly to your ball lock homebrew keg. Be sure to select the correct size QD fittings that correspond to your tubing's outer diameter (OD). Specifications: Inner Diameter - 3 mm (1/8") Outer Diameter - 6.35 mm (1/4") PVC, BPA , and Plasticizer Free* Stiff outer wall is kink resistant and easy to use with Duotight fittings Smooth inner wall prevents oxidation, CO2 loss and microbial growth build-up *EVABarrier does not contain plasticizers, or phthalates, that are used to make PVC flexible. These plasticizers are known to leach out into the beer over time and have adverse health effects. KegLand Part Number: KL42789
$28.49
-
LinkTech High Temp Plastic Female Quick Disconnect (QD) | 3/8" Barb w/ Shutoff Valve
The LinkTech 60PS Series is a lineup of premium plastic Quick Disconnects. These High Quality QDs are made from medical grade polypropylene, a high-strength plastic that is temperature tolerant 160° (Max!), and can handle pressure ranging from a vacuum to 60 psi. All of the 60PS Series will interconnect, and these units will also work seamlessly (and leaklessly!) with CPC Quick Disconnects of the same internal 3/8” flow path. O-rings are a EPDM Rubber, and internal valve springs are constructed from 316 Stainless steel. This is a Female Socket, which can connect to any H501 Series Male Plug. It has a 3/8" Hose Barb on the other end for attaching any 3/8" ID tubing. This QD is equipped with a shutoff valve. When not connected to another QD, this will not allow any flow. While not quite as bulletproof as our Stainless Steel Quick Disconnects, this lineup does offer a few advantages. These can be set up with Shutoffs, which will prevent flow when disconnected, and can be incredibly useful on Pump or Glycol systems. The pricing of these products is more economical, yet the plastic is still medical grade. All in all, these are a premium lineup of quick disconnects with great features and lots of options. Features: LinkTech brand 60PS Series Equipped with Shutoff Valve Connections: Female Socket Quick Disconnect 3/8" Barb Medical Grade Materials: Body: High-Strength Polypropylene Spring: 316 Stainless Steel O-Ring: EPDM Operating Pressure: Vacuum to 60 PSI Temperature Tolerance: -40 to 280°F (-40 to 138°C) 3/8" Flow Path Interchangeable with CPC - Colder HFC35 Series
$25.99
-
Stainless Tri-Clamp Ferrule | 4" T.C.
4" TC Ferrule is used to weld in a TC connection anywhere you need one! 304 Stainless Steel
$15.49
-
ForgeFit® Stainless Tri-Clamp Eccentric Reducer | 2" x 1.5"
2" x 1.5" tri-clamp eccentric reducer. Made from 304 stainless steel.
$54.49
-
ForgeFit® Stainless Tri-Clamp Extension Tube (Spool) | 1.5" T.C. | 24" Long
304-type stainless steel tri-clamp extension tube with 1.5" clamp ends. 24" long.
$67.49
-
ForgeFit® Stainless Tri-Clamp Extension Tube (Spool) | 2" T.C. | 12" Long
304-type stainless steel tri-clamp extension tube with 2" clamp ends. 12" long.
$43.99
-
ForgeFit® Stainless Tri-Clamp Extension Tube (Spool) | 2" T.C. | 18" Long
304-type stainless steel tri-clamp extension tube with 2" clamp ends. 18" long.
$54.99
-
ForgeFit® Stainless Tri-Clamp Extension Tube (Spool) | 2" T.C. | 24" Long
304-type stainless steel tri-clamp extension tube with 2" clamp ends. 24" long.
$59.49
-
ForgeFit® Stainless Tri-Clamp Eccentric Reducer | 3" x 2.5"
3" x 2.5" tri-clamp eccentric reducer. Made from 304 stainless steel.
$125.99
-
ForgeFit® 3 in. Butterfly Valve Gasket
Replacement gasket for the ForgeFit® 3" butterfly valve. We recommend replacing your butterfly gasket at least every 3 years. If you wait until you have a leak, your valve has already been unsanitary for some time.
$42.49
-
Replacement Gasket for ForgeFit® Tri-Clamp Sight Glass - 1.5 in.
Replacement internal gasket for the ForgeFit 1.5" T.C. Sight Glass. There is a gasket at both ends of the sight glass, so be sure to order two if you need to replace both gaskets.
$2.99
-
Replacement Gasket for ForgeFit® Tri-Clamp Sight Glass - 2 in.
Replacement internal gasket for the ForgeFit 2" T.C. Sight Glass. There is a gasket at both ends of the sight glass, so be sure to order two if you need to replace both gaskets.
$2.99
-
Stainless Tri-Clamp Extension Tube | Spool | 4" x 2"
This tri-clamp extension tube features 4" tri-clamp connections at both ends and is made from high-quality stainless steel. Extension tubes (or spools) are an easy way to extend the length of any T.C. fitting. 4" tri-clamp 2" long Made from 304 stainless steel
$79.99
-
Vacuum Breaker with Back Gas Port - 1.5 in. T.C.
This clever device allows you to back fill your tank with an inert gas while cold crashing to avoid the ingress of O2 through the vacuum relief. It is normally used on a tee with a normal PRV/Vacuum Breaker. The NPT port is hooked up to a regulator and set to a low pressure. The exact setting used will depend on the volume of your head space and your regulator. Start at 2 PSI and adjust from there. A pin spanner is required for disassembly. 1.5" tri-clamp 1/2" female NPT port
$87.99
-
BrewBuilt® Thermowell Offset | 1.5" T.C.
This unique thermowell fitting is has the probe offset from the center of the fitting, leaving room for additional hardware such as the BrewBuilt Whirlpool Return Fitting. Pairing the two fittings allows you to recirculate wort in your boil kettle while still getting temperature readings from your thermometer or temperature probe. The thermowell has a 6" probe that fits all BrewBuilt kettles so that you can get the most accurate temperature measurement of your wort.
$29.99
-
Ss Brewtech 1.5 in. T.C. Thermowell
Features: 304 Stainless Steel Compatible with 1/4" probes Does not include TC gasket 2.75" Thermowell
$25.95
-
BrewBuilt® Whirlpool Return Fitting & Thermowell Offset Kit | 1.5" T.C.
Recirculate wort in your boil kettle without sacrificing one of your tri-clamp ports. The BrewBuilt Whirlpool Return Fitting & Thermowell Offset kit allows you to use any tri-clamp kettle's thermometer port to recirculate wort while also taking temp readings. This kit is perfect for kettles that only have two tri-clamp ports—eliminating the need to drill out a hole in your kettle to add a third port for wort recirculation. Attach your preferred valve or tri-clamp fitting to the side inlet and, during whirlpool, draw wort from your bottom port and pump it back through the Whirlpool Return Fitting. Kit Includes: Whirlpool Return Fitting Thermowell Offset (1) 1.5" Tri-Clamp (1) 1.5" Tri-Clamp Gasket (EPDM)
$99.99
-
MB® Tri-Clamp Spunding Valve | 2 BAR | 15-30 PSI | 1.5" T.C. | Etched Pressure Scale | Hand Adjustable | Polycarbonate Liquid Cylinder | Stainless Steel
Ferment under pressure with precisely tuned pressure settings Pressure fermentations help to suppress unwanted esters Make clean lagers faster and at higher temperatures Easy-to-read etched pressure scale from 15 to 30 psi Hand adjustable—turn clockwise or counterclockwise to raise or lower your setting Made from 304 stainless steel with polycarbonate cylinder MB is a brand dedicated to crafting and sourcing high-quality, professional-level brewing supplies The MB T.C. spunding valve will give you the highest level of accuracy when fermenting under pressure. Designed for use with any pressurizable stainless steel conical with 1.5" T.C. top ports. For larger units, the spunding valve can also be integrated into the blowoff pipework and used with a pressure gauge and tri-clamp tee. The polycarbonate cylinder that surrounds the spunding valve can be filled with water or sanitizer to keep your tank 100% sanitary throughout the fermentation process. Adjustable from 15-30 psi Made from 304 stainless steel 11.75" H x 4" Ø For Your Safety: Never exceed the maximum rater working pressure of your vessel at any time during operation. The fixed-pressure PRV on your conical should always remain in place while using this spunding valve.
$199.99
-
Tri-Clamp Spunding Valve | Replacement Sealing Ring
Replacement sealing O-ring for 1.5" stainless tri-clamp spunding valves. Single ring. Made from EPDM. This is the O-Ring for the reservoir. Compatible with the BrewBuilt® and MB® tri-clamp spunding valves.
$3.29
-
ForgeFit® Stainless Tri-Clamp Elbow | 45° | 1.5"
304-type stainless steel tri-clamp 45° elbow with 1.5" clamp ends.
$27.49
-
Plastic Sight Glass Lens | 2" Tri-Clamp | Transparent T.C. End Cap
This sight glass lens is suitable for use with any 2" tri-clamp ferrule with a 2" clamp and gasket. Made of Polyphenylsulfone (PPSU) which offers the clarity of transparency of glass with a much higher shatter and heat resistance. PPSU is an excellent choice for components that are exposed to high temperatures (up to 392°F) and corrosive media due to its exceptional chemical resistance, as well as being extremely impact resistant, and with the added benefit of being see-through. KegLand Part Number: KL25973
$13.49
-
Plastic Sight Glass Lens | 3" Tri-Clamp | Transparent T.C. End Cap
This sight glass lens is suitable for use with any 3" tri-clamp ferrule with a 3" clamp and gasket. Made of Polyphenylsulfone (PPSU) which offers the clarity of transparency of glass with a much higher shatter and heat resistance. This is a direct replacement part for the Pro Sight Glass Distillation Lid. PPSU is an excellent choice for components that are exposed to high temperatures (up to 392°F) and corrosive media due to its exceptional chemical resistance, as well as being extremely impact resistant, and with the added benefit of being see-through. KegLand Part Number: KL22071
$14.49
-
Replacement Reservoir for Tri-Clamp Spunding Valve
Replacement reservoir for 1.5" tri-clamp spunding valve. Compatible with both 1 BAR BrewBuilt model (CON4P36) and 2 BAR MB model (CON4P35-MB).
$18.99
-
ForgeFit® Stainless Ball Valve | Full Port | 2" T.C.
This 2" tri-clamp ball valve is full port and completely disassembles for easy sanitation. It is perfect for inserting a mixer into a wine tank or for mixing hops in a beer tank. No tools are required for disassembly. Simply turn the valve to the closed position, remove the 3.5" tri-clamp, remove the bottom thumb screw (drain), and tilt the ball out of the socket by rotating the top towards you. Reassemble in reverse order. Use food safe grease on all surfaces. Note: Take care to not allow fermentation inside the valve. Do not open the valve during fermentation. The drain screw can be removed while the valve is closed to drain the valve. 2" tri-clamp 3.5" T.C. assembly Made from 304 stainless steel
$161.49
-
Tri-Clamp Gasket with Stainless Mesh Screen | 7 Mesh | Teflon | 3"
Teflon gasket with 304 stainless mesh screen for 3" tri-clamp connections. Can be used as a filter screen to trap large particulates passing through T.C. fittings. Often used for distillation to retain activated carbon for filtering neutral spirits or used in pot distillation to retain botanicals in the vapor stream. The screen has a mesh size of 7 which will block particles larger than 2.83mm or 2830 microns. This slightly larger mesh size makes this screen ideal for use in a distillation basket. KegLand Part Number: KL28868
$10.99
-
Tri-Clamp Gasket with Stainless Mesh Screen | 7 Mesh | Teflon | 4"
Teflon gasket with 304 stainless mesh screen for 4" tri-clamp connections. Can be used as a filter screen to trap large particulates passing through T.C. fittings. Often used for distillation to retain activated carbon for filtering neutral spirits or used in pot distillation to retain botanicals in the vapor stream. The screen has a mesh size of 7 which will block particles larger than 2.83mm or 2830 microns. This slightly larger mesh size makes this screen ideal for use in a distillation basket. KegLand Part Number: KL28394
$12.49
-
Stainless Tri-Clamp | 3 Piece | 4" Clamp
This stainless steel tri-clamp features two hinges and folds into three pieces. Some brewers find this style of clamp easier to work with on large equipment that requires a 4" clamp. KegLand Part Number: KL32902
$16.99
-
ForgeFit® Stainless Tri-Clamp Elbow | 90° | 3" T.C.
This elbow fitting features 3" tri-clamp connections at both ends and is made from high-quality stainless steel. Perfect for pairing with the BrewBuilt X3 Conical's 3" bottom port for routing yeast and trub dumps. 3" tri-clamp 90° bend Made from 304 stainless steel
$76.99
-
ForgeFit® Stainless Ball Valve | 2" T.C. | Rebuild Kit
This rebuild kit includes a 3.5" T.C. Gasket and 3mm x 77mm O-ring to aid in the repair of the ForgeFit 2" T.C. Ball Valve. The 3.5" T.C. Gasket requires a food grade grease for assembly with the FF190 Ball Valve.
$5.49
-
ForgeFit Stainless Tri-Clamp Gasket | EPDM | 3.5"
EPDM gasket for 3.5" tri-clamp connection. Temperature rated from -30°F to 300°F. This gasket is a direct replacement part for the ForgeFit 2" Full Port Ball Valve.
$1.99
-
Stainless Ball Valve - 3/8" Full Port
Our Ball Valves will last for years. Easy to clean. High grade 304-stainless made to last. 3/8" FPT on input and output side. TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and two gaskets that form the seal when closed.
$16.49
-
Stainless - 1/4 in. FNPT Elbow
Stainless 1/4 in. FNPT Elbow
$5.49
-
Stainless - 3/8" Comp. x 1/2" MPT
A great way to set up a homemade Mash Tun. These fittings are designed to thread into the inside of a bulkhead fitting, and clamp down on a copper or stainless tube to allow for a hard-plumbed false bottom! Simply thread the fitting into your bulkhead, loosen the nut, and slide your tubing in! Tightening down the nut with tubing inside will clamp the internal locking mechanism onto your metal tube, creating a seal, and insuring a happy mash tun, happy beer, and happier drinkers! 304-Type Stainless Steel compression fitting. 1/2" Male Pipe Thread with a 3/8" compression fitting on the other side.
$16.49
-
Stainless - 1/2" Comp. x 1/2" MPT
304-Type Stainless Steel compression fitting.
$19.99
-
Stainless Compression Fitting | 1/2 in. x 1/2 in. FPT
304-Type stainless steel compression fitting.
$28.99
-
Stainless - 5/8" Comp. x 1/2" FPT
304-Type stainless steel compression fitting.
$32.99
-
Stainless - 1/4 in. Coupler
Stainless 1/4" Coupler
$6.59
-
Stainless Full Coupler - 1/4 in. BSPP
Full Coupler with 1/4" Female BSPP Thread. Full couplers have threads for insertion from both sides. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL06477
$2.79
-
Stainless Hex Nipple - 1/8 in. BSP
An excellent upgrade to a standard nipple, these have a hex nut in the center to allow easy tightening and loosening in whatever application it's used! 1/8" male BSP threads. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL06422
$2.79
-
Stainless Hex Nipple - 1/4 in. BSP
An excellent upgrade to a standard nipple, these have a hex nut in the center to allow easy tightening and loosening in whatever application it's used! 1/4" male BSP threads. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL06439
$2.79
-
Stainless Lock Nut - 1/4 in. BSPP
Stainless Lock Nut. 1/4 in. Female BSPP. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL06507
$2.79
You have seen 480 out of 504 products