Whether you're a professional winery, or are making small batches in your kitchen, hardware parts will be necessary. We offer dozens of hardware parts, from hose clamps to butterfly valves. Any hardware you'll need to make great wine can be found in the categories below!
Wine Making Hardware
Shop By Collection
-
CMBecker Pin Lock Quick Disconnect (QD) | Beverage Out | Barbed | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA
This is a high quality fitting made by CM Becker in Germany. Red body with black top. 3 pin. 1/4'' barb fitting.
$7.99
-
CMBecker Pin Lock Quick Disconnect (QD) | Gas In | Flared | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA
This is a high quality fitting made by CM Becker in Germany. Red body with gray top. 2 pin. 1/4'' male flare fitting.
$7.99
-
KOMOS® CO2 Regulator to Nitrogen or Argon Tank Adapter | CGA320 Male Thread by CGA580 Male Thread
With this adapter you can use a KOMOS CO2 regulator with a Nitrogen or Argon tank. Not all CO2 Regulators are suitable for use with a Nitrogen tank. Only for use with KOMOS regulator which is a dual gas regulator capable of handling Nitrogen and CO2 gasses. CGA320 male thread by CGA580 male thread. Compatible with KOMOS Dual Gauge and Dual Body regulators.
$24.99
-
Stepless Hose Clamp - 5/16 in. - 3/8 in. OD Tubing (20 Pack)
These stainless stepless clamps tighten in an exact circle, making them ideal for use with draft lines. Suitable for 5/16" to 3/8" OD tubing (7-10 mm OD). Comes in packs of 20 clamps. Stepless Clamp Tool sold separately - H1006 Kegland Part Number: KL06682
$10.99
-
High Temp Silicone Tubing | Reinforced | 3/8" ID
The construction of braided silicone enables the tubing to handle increased pressure applications. Reinforced silicone offers outstanding resistance to temperature extremes and is made from FDA-sanctioned ingredients. The flexible design and construction of this tubing allows excellent bend radii and permits installation in restricted spaces without impeding flow. 3/8" inner diameter, 5/8" outer diameter Open mesh polyester braiding incorporated within the wall of silicone tubing Made from FDA-sanctioned ingredients Translucent natural color for visual contact with the flow Able to resist extreme temperature variation: -40°F to 392°F (-40°C to 200°C) Odorless, tasteless, and inert Working Pressure: 94 psi Burst Pressure: 275 psi Platinum cured Conforms to FDA CFR 177.2600, NSF
$46.49
-
High Temp™ PVC Free Tubing - 1/2 in.
EJ Beverage High Temp tubing is perfect for use on the hot side of your brewing system. When compared with traditional Silicone this tubing is less likely to kink at higher temperatures. It is constructed of TPE (Thermoplastic Elastomer) which is an excellent alternative to high temperature PVC and Silicone. The advantages to this high temperature tubing are: PVC & BPA Free. Contains no DEHP phthalates or other plasticizers High temperature up to 135° C (275° F) Extremely low extractables Extremely low leachables High flexibility Remains flexible at high temperatures Ultra-low permeability Barrier properties 1/2” ID x 3/4” OD Environmentally friendly production - does not emit dioxins Burst Pressure = 63 psi Working pressure of 21 psi
$16.49
-
Stainless Tri-Clamp | 2" T.C. x 3/4" BSPP Female
Convert 3/4" BSPP (Straight Thread) fittings to 2" Tri-Clover.
$28.99
-
Stainless - 4 in. T.C. x 2 in. T.C. Concentric Reducer
Stainless steel Tri-Clamp reducer going from 4" T.C. to 2" T.C. Kegland Part Number: KL06156
$54.99
-
ForgeFit® 2 in. Butterfly Valve Gasket
Replacement gasket for the ForgeFit® 2" butterfly valve. We recommend replacing your butterfly gasket at least every 3 years. If you wait until you have a leak, your valve has already been unsanitary for some time.
$24.49
-
Stainless Tri-Clamp | 1.5" T.C. x 1/2" BSP Female
1.5" tri-clamp with 1/2" BSP female threads. Made from 304 stainless steel. This adapts the beer-in for the Canular KEG500 to TC. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL25362
$16.49
-
Stainless - Full Coupler - 1/2 in.(BSPP)
Full Coupler with 1/2" Female British Standard Pipe Parallel Thread. Full couplers have threads for insertion from both sides.
$5.49
-
Stainless Bushing - 1/2 in. x 3/4 in. BSP
1/2" female x 3/4" male BSP reducing bush. Made from 304 stainless steel. Kegland Part Number: KL06583
$4.99
-
Brass Hose - Female Hose x 1/2'' fpt Swivel
Female Garden Hose Thread on one side, 1/2" FPT on the other. Useful piece for adapting Quick Disconnects to Wort Chillers or Water Filters.
$3.89
-
Add On Assembly For Gas Manifold
So you had the great foresight to buy our modular gas line manifold and now you are adding a keg. You need gas on that keg. No problem, use our add on assembly to expand your existing manifold. Includes a shut off check/ball valve, one tee and a connecting nipple.
$15.49
-
CMBecker Pin Lock Quick Disconnect (QD) | Gas In | Barbed | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA
This is a high quality fitting made by CM Becker in Germany. Red body with gray top. 2 pin. 1/4'' barb fitting.
$7.99
-
ForgeFit® Tri-Clamp Gasket | EPDM | 4"
EPDM gasket for 4" tri-clamp connection. Temperature rated from -30°F to 300°F.
$3.99
-
ForgeFit® Stainless Tri-Clamp End Cap | 4"
End cap for 4" tri-clamp fittings. Made from 304 stainless steel.
$26.49
-
ForgeFit® Stainless Tri-Clamp Elbow | 90° | 2"
304-type stainless steel tri-clamp 90° elbow with 2" clamp ends.
$35.99
-
ForgeFit® Stainless Tri-Clamp Concentric Reducer | 3" x 2.5"
3" x 2.5" tri-clamp concentric reducer. Made from 304 stainless steel.
$49.99
-
ForgeFit® Stainless Butterfly Valve | 3" T.C.
This 3" Tri-Clamp Butterfly Valve features stainless steel construction and 7-position handle. The handle can be rotated 180° for right or left hand operation.
$236.49
-
Stainless Hex Nipple - 3/4 in. BSP
An excellent upgrade to a standard nipple, these have a hex nut in the center to allow easy tightening and loosening in whatever application it's used! 3/4" male BSP threads. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL06460
$4.99
-
Stainless Barb - 3/8 in. Male BSPP x 3/8 in.
This Stainless Steel BSPP barb will connect any tubing with a 3/8" ID line to any fitting with a 3/8" Female BSPP connection. The barb is slightly oversized at 10 mm (0.39") compared to 3/8" (0.37") which will give you a tighter connection with your tubing. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL06644
$3.29
-
Brass - 1/2" Flat Nut
1/2" NPT flat nut
$2.99
-
Brass Hose - Male Hose x 1/2'' mpt
Useful Part for adapting Garden Hose Thread to standard NPT. Male Garden Hose Thread with 1/2" MPT on the other side.
$7.99
-
Gas Tubing Assembly - Pin Lock Quick Disconnect (QD)
Includes pin lock gas in quick disconnect, line and two hose clamps.
$16.99
-
Firestone Poppet | Ball Lock | Corny Keg Part
For Firestone brand ball lock kegs. It will fit the Firestone V Challenger, VI Challenger and Super Challenger kegs. Each keg used two poppets.
$15.99
-
Firestone Poppet | Pin Lock | Corny Keg Part
For Firestone brand Pin Lock kegs. Also fits older John Wood pin lock kegs. Each keg used two poppets.
$17.99
-
Torpedo Keg Dip Tube | Gas In | Corny Keg Part
Replacement Gas In dip tube for Torpedo Kegs. Stainless steel construction, approximately 1" in length.
$3.99
-
CMBecker Inline Check Valve | Quick Disconnect (QD) | Flared
This inline check valve can be used with any gas-in ball lock or pin lock flared disconnect. Allows gas to flow through while preventing the backflow of liquid. Made in Germany and assembled in the USA by CM Becker.
$9.99
-
Torpedo Keg | Ball Lock Keg | Stainless Steel Corny Keg | Low2 Keg Lid O-Ring | Superior Oxygen Barrier Properties | 6 Gallon
Oversized corny keg, great for bigger batches and fermentation Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Brand new, all-stainless construction ball lock keg Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Set your sights on a brand new Torpedo Keg! The patented, D794,899, sleek all-stainless design represents the pinnacle of quality in ball lock homebrew kegs. With features like welded stainless handles, the ability to stack with fittings in place, amazing quality and a great price we think these kegs will become the standard by which other kegs are measured. Quality First The first thing we at MoreBeer! check out is interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. These kegs are machine welded and exceed our standards for quality. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. In and Out is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Stainless Fermenter We've seen a lot our customers having great success using the 6-gallon Torpedo Keg as a stainless steel fermenter or "kegmenter". The extra headroom that this size offers makes it a great option for fermenting 5-gallon batches. We highly recommend using CellarScience Foam Axe if you're fermenting in the keg. Foam Axe will help reduce krausen buildup, cutting down the chance of clogging issues with the ball lock poppets and the PRV in the keg lid. It should also be noted that leaving your finished beer on the leftover trub from fermentation for too long will eventually lead to off-flavors. If it won't be consumed in 2-3 weeks, transfer your beer to a fresh keg using the Torpedo Keg Buoy which will pick up the clearest beer and leave the sediment behind. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions: 27.15" H x 9" D
$159.99
-
High Temp™ PVC Free Tubing - 3/8 in.
EJ Beverage High Temp tubing is perfect for use on the hot side of your brewing system. When compared with traditional Silicone this tubing is less likely to kink at higher temperatures. It is constructed of TPE (Thermoplastic Elastomer), which is an excellent alternative to high temperature PVC and Silicone. The advantages to this high temperature tubing are: PVC & BPA Free. Contains no DEHP phthalates or other plasticizers High temperature up to 135° C (275° F) Extremely low extractables Extremely low leachables High flexibility Remains flexible at high temperatures Ultra-low permeability Barrier properties 3/8” ID x 5/8” OD Environmentally friendly production - does not emit dioxins Burst Pressure = 54 psi Working pressure of 18 psi
$10.49
-
High Temp Silicone Tubing | Reinforced | 1/2" ID
Reinforced silicone tubing offers higher temperature tolerances and chemical resistance while remaining flexible and easy to handle. Ideal for both cold side and hot side processes and high-pressure applications. Although braided, the tubing remains transparent to allow you to visually inspect the flow of liquids. 1/2" inner diameter 3/4" outer diameter Odorless, tasteless and inert Polyester heat resistant fiber reinforcing braid Good electrical and weatherability properties Resists UV, Ozone, gases, and moisture Working Temperature: -76°F–500°F Working Pressure: 0-150 psi KegLand Part Number: KL25300
$10.99
-
Brass Hose - Male Quick Disconnect (QD)
This is the male side of the Garden Hose Quick Disconnects. This set enables you to quickly and efficiently connect and disconnect lines from your Wort Chiller, Water Filter, or whatever else you feel could be improved through quicker connections! This product is designed to work in conjunction with our Female Garden Hose Quick Disconnect. Please Note: This product will NOT work with our Stainless or Plastic Quick Disconnects.
$6.99
-
Stainless Steel Camlock - Male Cam X 1/2 in. Female (Type A)
Type A Camlock Fitting. Male Camlock with 1/2" Female BSP. Camlocks are considered by many to be the superior quick connect fitting. They have a higher working pressure and hold a tighter seal than quick disconnect fittings, making them less likely to leak while in use. Locking and unlocking the female pieces may require two hands, but it's a small price to pay for long-lasting reliability. 304 Stainless steel construction. 150 psi working pressure. Kegland Part Number: KL04503
$9.89
-
Stainless Steel Camlock - Female Cam X 1/2 in. Male (Type B)
Type B Camlock Fitting. Female Camlock with 1/2" Male BSP. Camlocks are considered by many to be the superior quick connect fitting. They have a higher working pressure and hold a tighter seal than quick disconnect fittings, making them less likely to leak while in use. Locking and unlocking the female pieces may require two hands, but it's a small price to pay for long-lasting reliability. 304 Stainless steel construction. 150 psi working pressure. Kegland Part Number: KL04480
$15.49
-
Stainless Steel Camlock - Male Cam X 1/2 in. Barb (Type E)
Type E Camlock Fitting. Male Camlock with 1/2" Barb (13mm). Camlocks are considered by many to be the superior quick connect fitting. They have a higher working pressure and hold a tighter seal than quick disconnect fittings, making them less likely to leak while in use. Locking and unlocking the female pieces may require two hands, but it's a small price to pay for long-lasting reliability. 304 Stainless steel construction. 150 psi working pressure. Kegland Part Number: KL04527
$8.79
-
Beer & Gas Tubing Quick Disconnect (QD) - 3/8 in. Barb x Male QD
Plastic quick disconnect with 3/8" barb which can be used with either 1/4", 5/16" or 3/8" line. The quick disconnect functionality is activated by a shrouded thumb latch on the female QD. The temperature range is -40F to 180F. They can handle a vacuum to 120 psi - so you need not worry about them leaking gas. The o-ring is food grade buna-n. This is a non-valved QD. It does not have an internal shut-off like H550A. For the female side, see our H550B.
$5.99
-
Stainless Tri-Clamp - 3 in. Elbow
A set of "elbows" is great for connecting hoses to a pump so they run parallel to each other. With 2" and 3" hose, this dramatically reduces the space needed to allow the pump to pass. In addition, having the lines run parallel makes the pump more agile when moving around the brewery or winery when connected. 304-type polished stainless.
$60.99
-
Stainless Tri-Clamp Sample Valve Shank | 1.5 in. T.C. x Beer Faucet Shank | Intertap® | NukaTap®
These long shanks are suitable to attach to large commercial fermenters and brite tanks with a 1.5" Tri-Clamp Port. Being removable and completely washable it makes this device extremely easy to clean and sanitize before use. Ideally used with the NukaTap Flow Control Faucet with Self-Closing Spring. Please note standard NukaTap SS Faucet and Self-Closing Spring will not work with this shank. You can use a NukaTap SS faucet, but without the autoclose spring. Also compatible with Intertap, Perlick, and other faucets. Specifications: 2.75" total length Standard shank assembly 1.5" T.C. connection KegLand Part Number: KL19989
$21.99
-
CIP Spray Ball | 4" x 1.5" Tri-Clamp
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory. This stainless steel CIP spray ball kit is perfect for homebrew conical fermenters as many popular units out there feature a 4" T.C. top port or clamp-on lid with 4" T.C. ferrule. Tri-clamp gasket not included. Kit Includes: 4" T.C. Cap with 1.5" T.C. x 1" BSP Male Thread connections 1" BSP x CIP Spray Head Requires pump with 12 GPM flow rate KegLand Part Number: KL22989
$65.99
-
Stainless Barb - 3/4 in. Male BSPP x 3/4 in.
This Stainless Steel BSPP barb will connect any tubing with a 3/4" ID line to any fitting with a 3/4" Female BSPP connection. The barb is slightly oversized at 20mm (0.78") compared to 3/4" (0.75") which will give you a tighter connection with your tubing. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL06668
$5.49
-
Vinyl Air Tube for Marchisio Variable Volume Tanks | 80 cm Diameter
Replacement air tubes for variable capacity tanks. 80 cm tube fits Marchisio 500-700 Liter tanks. Please note: These tubes are only compatible with Marchisio brand tanks. They will not work with Speidel or other brands of variable volume tanks.
$49.99
-
Pressure Gauge (RHT) | High Pressure (0-3000 PSI) | CO2 or Nitrogen Regulator | 1/4" MPT Right-Hand Thread
3000psi gauge tells tank pressure. Right hand thread replacement gauge for most brands of regulators.
$16.49
-
KOMOS® 2.5 lb CO2 Tank | Premium Aluminum | New | CGA320 Valve | US DOT Approved
Brand new aluminum 2.5 lb CO2 tank made from high strength aluminum alloy and high quality CGA320 valves. Because it is made of aluminum rather than steel you can feel confident that it won’t rust. It’s called a 2.5 lb tank because it holds 2.5 lbs of compressed (liquified) CO2. 2.5 lbs of CO2 is enough to dispense about 4x 5-gallon kegs of homebrew. Aluminum tanks are superior to steel because they do not rust. All tanks are shipped empty. To have tanks filled you will want to visit your local welding supply shop. Because you are purchasing a new tank you can choose to either have it filled or to exchange it for a filled tank at your local gas supplier. If you have this tank filled the local gas supplier is responsible for affixing the correct neck label that identifies the gas being put in the cylinder. Tanks should always be stored in an upright position. Features: Made from corrosion resistant, engineered Aluminum Brushed finish Thick, durable cylinder walls 14.75" T x 4.375 Ø DOT approved New high quality CGA-320 valve Light weight compared to steel tanks
$72.99
-
Duotight Draft Regulator Board | Gas Manifold | 4 Way
Serve beverages at different pressures without the need for multiple CO2 cylinders, dual body regulators, or expensive gas manifolds Feed a single pressure to the gas board from your regulator and then step down the pressure on each Duotight regulator Use one line for serving ales, another for soda or seltzer water, and another for carbonating a freshly filled keg All parts shown are included and snap together quickly thanks to Duotight push-to-connect fittings and rigid plastic joiners Duotight In-Line Regulators feature built-in pressure gauges that read 0-60 PSI and can be swapped out for different ranges if desired The Duotight Draft Regulator Board is a simple and cost-effective solution to serving beer and other beverages on draft at different pressures. With a standard CO2 tank and CO2 regulator, you can feed gas at a single pressure into the regulator board and then fine tune individual pressure settings for each gas line via the Duotight In-Line Regulators. These regulators feature built-in pressure gauges that make adjustments super simple and check valves are included as standard so you never have to worry about back flow into the regulator. This kit includes everything you need to assemble your regulator board and can be customized so the gas inlet is on the right or left side—whichever makes the most sense for your home draft setup. Duotight push-to-connect fittings and the precut rigid joiners make assembly a breeze and only takes 10-15 minutes! The draft board kit comes in two options—with or without shut off valves. These valves offer peace of mind and allow you to shut off gas flow to any line that is not in use. If you ensure that your system has no leaks, they aren't technically needed, and you can always fully tighten your Duotight Regulator adjustment knob for added protection. But that little extra security might help you sleep easier at night! One advantage of choosing no check valves, however, is that it will leave room at the top of the board to label your gas lines. One of the coolest features of the Duotight In-Line Regulator is that the included pressure gauge can be swapped out for different pressure ranges. The standard gauge reads 0-60 PSI, but if you have one line that will always be used for serving Ales, you can swap to a 0-15 PSI gauge that will be a little easier to read and make precise adjustments. There's also a Digital Pressure Gauge available that provides backlit instant reads and is rated from 0-90 PSI. Need more than 4 gas lines? Check out the 6-Way Duotight Draft Regulator Board. Please Note: Full assembly required. The gas board, regulators, and fittings will arrive loose. Please see our instructions and assembly video below. Stepping Down Pressure The ideal regulation scenario occurs when the inline regulator steps down the output pressure to at least 10 PSI less than the inlet pressure. For example, if the inlet pressure is 30 PSI, the regulator effectively manages a range from 0–20 PSI on the output side ensuring optimal performance and stability. Ideal regulation scenario (10 PSI less than inlet pressure) Example of 30 PSI inlet translating to 0–20 PSI output Kit Includes: 4-Output Gas Board (4) Duotight In-Line Regulators (4) Duotight Check Valves (4) Duotight Shut Off Valves (if selected above) (3) Duotight Tees (1) Duotight Elbow (15) Rigid Plastic Joiners NOTE: All Duotight fittings and rigid plastic joiners come as 8mm OD. Mounting hardware is included for the regulators but not for mounting the board itself to a wall or the inside of your kegerator/keezer. If you select the option without shutoff valves, you will be left with some spare joiners after assembly.
$98.99
-
Gas Add On Assembly - Ball Lock Quick Disconnect (QD)
Use this assembly to tee off from your CO2 system to add another keg to your existing draft system. Includes a Ball lock gas in quick disconnect.
$16.49
-
CMBecker Pin Lock Quick Disconnect (QD) | Beverage Out | Flared | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA
This is a high quality fitting made by CM Becker in Germany. Red body with black top. 3 pin. 1/4'' male flare fitting.
$7.99
-
KegLand Ball Lock Quick Disconnect (QD) | Beverage Out | Stainless Steel | Barbed
This is a ball-lock type quick disconnect that is constructed from stainless steel for lifetime longevity. 1/4" barb. This QD is for the Bev Out side. See here for the Gas In QD. 2 1/8" H Please note: the outer bushing on the disconnect is made from chrome-plated brass. All parts that come into contact with liquid are stainless. Kegland Part Number: KL02998
$18.99
You have seen 336 out of 504 products