Whether you're a professional winery, or are making small batches in your kitchen, hardware parts will be necessary. We offer dozens of hardware parts, from hose clamps to butterfly valves. Any hardware you'll need to make great wine can be found in the categories below!
Wine Making Hardware
Shop By Collection
-
ForgeFit® Stainless Tri-Clamp | 2.5" Clamp
The most popular choice for sanitary connections, tri-clamp fittings are widely used in the food & beverage industry due to their ability to be cleaned in place. Tri-clamps join two fittings together without any nooks or crannies for contaminants to hide. Use anywhere you want to ensure a sanitary connection. 2.5" tri-clamp Made from 304 stainless steel
$11.49
-
Tri-Clamp Spunding Valve | Integrated Pressure Gauge | Scaled Spunding Valve | Polycarbonate Liquid Cylinder | 2.2 BAR | 0-32 PSI | 1.5" T.C. | Stainless Steel
For commercial brewery application with a range of 0-2.2 Bar. For homebrew fermenters, see the BrewBuilt® Spunding Valve Automatically release pressure inside your fermenter during pressure fermentations Compatible with any stainless steel pressurizable fermenter with 1.5" tri-clamp ports In-line pressure gauge for easy reference of tank pressure reads from 0-35 PSI Made from 304 stainless steel and comes fully assembled This tri-clamp spunding valve provides professional-level accuracy for fermenting under pressure. Attach to any pressurizable stainless steel conical with 1.5" TC ports and set your desired blow-off pressure. A pressure gauge sits in-line from the conical to the spunding valve so you can reference the current pressure inside your vessel at any time. The polycarbonate cylinder that surrounds the spunding valve can be filled with water or sanitizer to keep your tank 100% sanitary throughout the fermentation process. Not designed for homebrewing conicals where the maximum allowed pressure does not exceed 1 Bar. The pressure gauge reads from 0-35 psi or 0-0.25 MPa. The spunding valve is scaled in both psi and BAR, up to 32 psi (2.2 BAR). Comes fully assembled 1.5" tri-clamp connection In-line pressure gauge Made from 304 stainless steel For Your Safety: Never exceed the maximum rated working pressure of your vessel at any time during operation. The fixed-pressure PRV on your conical should always remain in place while using this spunding valve.
$299.99
-
Stainless - 1 in. Full Coupler BSPP
Full Coupler with 1" Female British Standard Pipe Parallel Thread. Full couplers have threads for insertion from both sides.
$7.69
-
Stainless - 1" MPT x 1/2" FPT Bushing
This bushing is to use when you want to use your larger pumps with an other fitting.
$6.09
-
Rubber Stopper - #13 Solid
#13 stopper - solid. Top diameter 2.64 inches (67 mm), bottom diameter 2.28 inches (58 mm), length 1 inch (25 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. Max. Temperature Rating: 158 °F (70 °C).
$6.49
-
KOMOS® Gas Manifold | Aluminum | 1/4 in. Flare
The KOMOS gas manifold features 1/4" flare gas inlet and check valves for much more flexibilty when choosing your draft line. Use 1/4" or 5/16" gas line with the appropriate Flare Fitting Set (KEG607 or KEG640), or use EVABarrier Draft Tubing with the appropriately sized Duotight fitting (DUO106 or DUO120). The check valves can also be replaced with a Ball Lock Post Bulkhead, allowing for the use of a gas-in ball lock jumper line as a quick connect option. If more than 4 outlets are needed, join multiple manifolds together with this 1/4" Nipple. Features: 1/4" Flare connections 1/4" BSP ball valves Rated to 100 psi Wall mount holes Made from aluminum, brass, and stainless steel Size Overall Length 2-way 5.25" 3-way 7.25" 4-way 9.25" The above measurements are from the tip for the brass flare inlet to the plug on the opposite end. Each manifold measures approximately 3.5" from the mounting holes to the tip of the valve.
$26.99
-
Torpedo Keg | Ball Lock Keg | Stainless Steel Corny Keg | 15 gal.
The newest addition to the Torpedo Keg arsenal! This ball lock keg has the same great features and superior quality as its predecessors, and will allow large-scale homebrewers to fit their entire batch into a single keg. These kegs are laser welded by an ISO certified commercial keg manufacturer, so you won't find any nooks or crannies for contaminants to hide. Made with rolled stainless steel handles that are comfortable to grab. "In" and "Out" are etched near the keg posts for a quick and mistake-free set up when connecting lines in a refrigerator or kegerator. The 10 and 15 gallon kegs can be stacked on top of each other with ball lock fittings still attached. Considering the price and quality, this Torpedo Keg is an amazing value! Specifications: Total Capacity: 15.2 gal. Max Pressure: 130 psi PRV Rating: 85 psi Height: 24.75" Diameter: 16.05" Made from 304 Stainless Steel
$269.99
-
KOMOS® | Stainless Butterfly Hose Clamps | 1/2 in. to 1 in. | 10-Pack
These stainless steel butterfly hose clamps are the ideal choice for connecting silicone tubing to quick disconnects, pumps, and more. The butterfly thumb screw allows for toolless tightening and untightening, so you can build out or break down your system without rummaging through the toolbox for the right screwdriver. Fits 1/2 in. OD to 1 in. OD tubing. Actual size of the clamp is 14-25 mm (0.55-0.98 in.). Comes in a convenient zip lock bag.
$10.99
-
Stainless Barb - 1/2 in. x 1/2 in. Male BSP
Stainless steel barb fitting. 1/2" male BSP x 13mm barb (0.51"). KegLand Part Number: KL03629
$6.59
-
Stainless Steel Camlock - Female Cam X 1/2 in. Barb (Type C)
Type C Camlock Fitting. Female Camlock with 1/2" Barb (13mm). Camlocks are considered by many to be the superior quick connect fitting. They have a higher working pressure and hold a tighter seal than quick disconnect fittings, making them less likely to leak while in use. Locking and unlocking the female pieces may require two hands, but it's a small price to pay for long-lasting reliability. 304 Stainless steel construction. 150 psi working pressure. Kegland Part Number: KL04497
$14.49
-
ForgeFit® CIP Spray Ball - 1.5 in. T.C.
1.5" tri-clamp "clean in place" spray ball. A pump capable of 29 PSI minimum is recommended for this product.
$41.49
-
ForgeFit® Stainless Tri-Clamp End Cap | 3"
End cap for 3" tri-clamp fittings. Made from 304 stainless steel.
$8.49
-
ForgeFit® Stainless Tri-Clamp Concentric Reducer | 3" x 2"
3" x 2" tri-clamp concentric reducer. Made from 304 stainless steel.
$48.49
-
Gaskets | Body Connect | Corny Keg Part
The gaskets on the body connects that the ball or pin lock fittings slide over. 7/16" ID with a 3/32" cross section. Made of FDA BUNA-N rubber. We also use this as a replacement for the smaller compression ring in our 1/2" Compression fittings so that you can create a snug fit in a Sanke keg conversion kit without permanently compressing a ring on the pick up tube.
$0.99
-
Torpedo Keg Sleeve
Neoprene keg sleeves for standard Torpedo Kegs. For the Slimline series sleeves, see KEG651. 6mm thick. The 5-gallon sleeve is also compatible with 1/6 bbl or sixtel commercial sanke kegs.
$16.49 $14.09
-
Duotight In-Line Regulator | Built-In Pressure Gauge | 0-60 PSI | Liquid & Gas Compatible | 8 mm Duotight
The Duotight In-Line Regulator works with both gas and liquid. Easily adjust the flow can be adjusted with the yellow adjustment knob. 8 mm Duotight fittings at both inlet and outlet make this unit perfect for use with EVABarrier 8 mm OD tubing (D1717 or D1718). Features an integrated pressure gauge so you can quickly and easily dial in your pressure setting. The analog gauge is removable and can be swapped out with a gauge of a different pressure range or it can be swapped out for the Digital Mini Pressure Gauge. Stepping Down Pressure The ideal regulation scenario occurs when the inline regulator steps down the output pressure to at least 10 PSI less than the inlet pressure. For example, if the inlet pressure is 30 PSI, the regulator effectively manages a range from 0–20 PSI on the output side ensuring optimal performance and stability. Ideal regulation scenario (10 PSI less than inlet pressure) Example of 30 PSI inlet translating to 0–20 PSI output Specifications: Made from food grade acetal Stainless screws Easily disassembles for cleaning 8mm (5/16") Duotight fittings at both ends Interchangeable pressure gauge Gauge reads from 0-60 psi Made with quality EPDM seals Wall mountable WARNING: Do not exceed gauge pressure. Exceeding the pressure range will damage the gauge. Kegland Part number: KL15035
$19.49 $14.69
-
Vinyl Beverage Tubing | Rigid | Draft Line | 3/8 in. ID | 5/8 in. OD
PVC tubing for gas and beer lines in kegging systems. 3/8 in inside diameter tubing with thick walls.
$6.09
-
Vinyl Transfer Tubing | Flexible | Racking | 1/8 in. ID | 1/2 in. OD
Used primarily in aeration and oxygentation systems that call for 1/8" ID line. 3/16" OD.
$3.69
-
Stainless Steel Camlock - Male Cam X 1/2 in. MPT (Type F)
Type F Camlock Fitting. Male Camlock with 1/2" BSP. Camlocks are considered by many to be the superior quick connect fitting. They have a higher working pressure and hold a tighter seal than quick disconnect fittings, making them less likely to leak while in use. Locking and unlocking the female pieces may require two hands, but it's a small price to pay for long-lasting reliability. 304 Stainless steel construction. 150 psi working pressure. Kegland Part Number: KL04510
$8.79
-
Stainless Tri-Clamp - 4 in. End Cap w/ Pre Drilled Hole
Use this 4" T.C. end cap to attach an airlock to your kegmenter unit. The hole measures 13/16", which is perfect for a #3 stopper (FE410VS). Kegland Part Number: KL06163
$14.49
-
ForgeFit® Tri-Clamp Gasket | Silicone | 4"
Silicone gasket for 4" tri-clamp connection. Temperature rated from -58°F to 446°F.
$4.49
-
Stainless - Full Coupler (1 in.)
Full Coupler with 1" Female Pipe Thread. Full couplers have threads for insertion from both sides.
$5.49
-
CellarScience® Universal Breathable Bung | Complete Set
Not sure what bung is right for you? We got your back! Get all the Breathable Bungs with this complete set. Includes: Breathable Carboy Bung Breathable Universal Bung Breathable Barrel Bung Breathable Bung for Glass Carboys A breathable Silicone stopper that acts as both a stopper and an airlock. Unique design allows CO2 pressure to escape but keeps Oxygen and airborne contamination out. This quickly became our stopper of choice for wine, and is a popular style used by numerous commercial wineries. Also has great application for beer ferments: It will create a vacuum if fermenting wort cools (as opposed to pulling water in from your traditional airlock.) Airtight seal is great for extended fermented lager when CO2 production is still present but very slight. Fits 3, 5, 6 & 6.5 gallon glass carboys, 1 gallon bottles, growlers, and 500 mL flasks. Replaces Stopper Sizes #6, #6.5, #7, #8 Stopper Measurements: 0.94" x 1.48" (24 mm x 37.5 mm) Universal Breathable Bung This CellarScience Bung has a ridge to keep it from getting sucked in and self-sealing vent holes to let air out but not in. They have a gentle taper, so they don’t slip out during use. They are also very easy to clean and sanitize. This a perfect fit for a 1.5” TC ferrules, Fermonsters, and Vintage Shop Plastic carboys. Replaces Stopper Sizes #8, #9. #10 Stopper Measurements: 1.36" x 1.89" (34.5 mm x 48 mm) Breathable Barrel Bung We recently discovered this premium breathable silicone barrel bung and were immediately impressed with its robust design and features. To start with, the ridge really helps make bung removal effortless. The bung acts as an airlock and allows the release of CO2 while maintaining a seal against oxygen coming in. This makes the bung ideal for alcoholic or malolactic fermentation in barrels or tanks. Fits 30- and 60-gallon barrels as well as the hole in the lid of most Variable Volume tanks! Also fits perfectly in a 2" tri-clamp ferrule Replaces Stopper Sizes #10 , #11, #12 Stopper Measurements: 1.65" x 2.19" (42 mm x 55.5 mm) The flapper stopper protrudes roughly 2.5" from the stopper
$32.99
-
Pressure Gauge (LHT) | High Pressure (0-3000 PSI) | CO2 or Nitrogen Regulator | 1/4" MPT Left-Hand Thread
3000psi gauge tells tank pressure. Left hand thread replacement gauge for some brand regulators.
$16.99
