Products

Convert a commercial sanke keg to be used with ball lock fittings. To install, remove the keg spear, place the gasket on the keg ferrule with the beaded side facing up, attach the silicone dip tube and place the tapping head on the ferrule, then secure with the 2" tri-clamp. Be sure to always depressurize the keg before removing the tapping head. Includes: Ball Lock Post Lid 2" tri-clamp Single-side beaded tri-clamp gasket 60 cm silicone dip tube (23.6") Red 2.5 bar PRV (36 psi) KegLand Part Number: KL10610  

Read more less

This easy to use and compact pressure relief valve is super handy for keg transfers. Using a ball lock quick disconnect as the main body, the valve easily snaps onto ball lock keg posts. Adjustable relief valves are a great way to limit oxygen exposure and regulate flow during closed keg transfers, The included gauge reads from 0-30 PSI and can be swapped out with a digital gauge or large face dial gauge for easier, more accurate readings. The black pull ring cap on the other end can be rotated for adjustments, or swapped to a range of color coded PRVs for a fixed pressure. This low-profile option only measures 1.75" in height. It works right out of the box but has several upgrade options as shown in the images. Warning: Never swap out the valve's standard PRV with a color coded PRV that exceeds the pressure rating of your vessel. Features: Duotight fitting where the gauge attaches This allows for upgrading the valve with a digital gauge or larger analog gauge Manual pull ring pressure relief This allows for you to not only adjust the pressure with the black rotary knob but also use the ring pull to instantly release pressure if you want to release manually Option for several color coded PRVs to be used (see below) Yellow - 17 psi Red - 35 psi Green - 65 psi Gray - 100 psi KegLand Part Number: KL29438

Read more less

Are you ever in a situation where you don't want to unhook your gas line from your kegs, or have ball lock disconnects that you need to clean over at the sink but don't want to take your gas line all the way over there? Why not fill a PET Bottle with your cleaner / sanitizer and pump it without gas! This little device can also be used as a mini party keg without a gas source (should be consumed well within 24 hours of pumping). Kit Contains: Yellow carbonation cap PCO Tee Piece (Female x Male x Male) Mini yellow hand pump 11.75" length of EVABarrier tubing (5mm ID x 8mm OD) PET Bottle not included KegLand Part Number: KL20220  

Read more less

This bev out ball lock bulkhead assembly allows you to add a ball lock post just about anywhere. Use in conjunction with the gas in bulkhead to create your own pressure vessel. The included short dip tube can be replaced with a longer dip suitable to your needs. 1/4" BSP threads and locking nut. Kegland Part Number: KL03162

Read more less

This gas in ball lock bulkhead assembly allows you to add a ball lock post just about anywhere. Create your own pressure vessel or attach it to one of our aluminum gas manifolds for a quick connect option. 1/4" BSP threads and locking nut. Kegland Part Number: KL03179

Read more less

This stainless QD with adjustable pressure relieve valve is a great accessory to have when performing pressure transfers. Made from stainless steel components for long-lasting quality. Features the Torpedo Keg gas-in disconnect and adjustable stainless gas pressure relief valve (D1833L). Looking for a PRV alve with pressure gauge? Check out the FIL42AS.  

Read more less

This Ball Lock QD With Pressure Gauge and Adjustable PRV is a great accessory to have when performing pressure transfers. Made from stainless steel components for long-lasting quality. Features the Torpedo Keg gas-in disconnect and adjustable stainless gas pressure relief valve (D1833L). This model also features a pressure gauge that reads from 0-15 psi. Don't need the gauge? Check out the FIL42S.  

Read more less

An Intertap accessory that converts the spout of an Intertap faucet into a ball lock quick disconnect. One of the most popular uses is being able to connect the beverage side of your counter pressure filler without having to open your refrigerator door. Compatible with Intertap and NukaTap faucets. Stainless Steel Construction Kegland Part number: KL01052

Read more less

The WilliamsWarn ball lock QD with CombiBarb connection allows you to connect draft lines using either standard hose & clamp or Duotight & EVABarrier tubing. The CombiBarb will accept 8 mm Duotight fittings for use with 8 mm OD EVABarrier, but also works perfectly well with 1/4" or 5/16" ID tubing.   

Read more less

Bev Out ball lock quick disconnect with 1/4 in. flare connection. Flare fitting barbs come in multiple sizes so you can choose the draft tubing size that best suits your needs. Features a built-in washer so you will not need a separate nylon washer. Manufactured in Germany by CM Becker. Packaged in the U.S. and distributed by KOMOS.

Read more less

Gas In ball lock quick disconnect with 1/4 in. barb connection. Recommended for use with 3/16 in. ID tubing for a tight fit. Manufactured in Germany by CM Becker. Packaged in the U.S. and distributed by KOMOS.  

Read more less

The WilliamsWarn ball lock QD with CombiBarb connection allows you to connect draft lines using either standard hose & clamp or Duotight & EVABarrier tubing. The CombiBarb will accept 8 mm Duotight fittings for use with 8 mm OD EVABarrier, but also works perfectly well with 1/4" or 5/16" ID tubing.   

Read more less

Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory. Relieves pressure while filtering from one keg to another plus allowing reading the pressure in the receiving keg.  Notes: The very end of the pressure relief valve can be adjusted by unscrewing to adjust the pressure. If tight, and not adjustable by hand, it needs to be loosened with pliers. Wrap a towel around the end piece of the pressure relief valve (about  the last 1/4 in) and loosen with pliers. Then finger tighten or loosen to desired pressure. Gauge reads 0 - 15 psi

Read more less

Replacement triangular plastic ball retainer for check valve assembly on Sanke couplers. This is the little plastic piece that holds the check valve ball in place.

Read more less

Nickel plated 1" ball valve. Male BSP x Female BSP. 

Read more less

Nickel plated 1/2" ball valve. Male BSP x Female BSP. 

Read more less

Nickel plated 3/4" ball valve. Male BSP x Female BSP.

Read more less

This cast iron wide-profile banjo burner is strong and efficient, topping our ratings in getting wort to a quick boil, while using the same amount or less of propane. Adjusted for efficiency this banjo burner produces around 70,000 BTU/hr, and in full, this banjo burner mode produces 100,000 btu.  Banjo burners can often times have issues when using with low flame output.  We sourced and tested a number of different units, before settling on this one, which performs great at low output.  Uses 3/8" male flare fitting (included). Comes with steel orifice plate for regulating airflow The burner has a 9 7/8" diameter and is 14 3/4" long This banjo burner requires a propane regulator to function properly.  We recommend a Wind Guard with these units if brewing outdoors.  If using indoors, you must have proper ventilation in the form of an overhead cooking hood.

Read more less

T-Corks are a great option for bottling your homemade concoctions. Dimensions: Top section is 28mm wide by 13mm high, lower cork section (that goes into the bottle) is 19mm wide by 20mm high. 

Read more less

Black Top Synthetic T-Cork Stopper. 22.2mm cork diameter. Direct replacement stopper for the 750 mL Sprit Bottle. KegLand Part Number: KL18890

Read more less

Bar Top T-corks offer the convenience of hand sealing, allowing you to easily reclose bottles  Whole natural cork stopper with black plastic head Premium stoppers for premium spirits, distillates and other shelf stable beverages 19.2mm cork diameter | Fits standard cork finish (neck) wine bottles & 375mL Farro spirit bottles Molinas Cork has been sustainability harvesting from the cork forests of Sardinia for over 100 years Bark is aged an additional year prior to harvest, leading to less porous, higher quality cork A high quality natural cork topped with a black plastic head.  Unlike the competition, which typically uses synthetic or agglomerated (particle board) stoppers, we chose high grade whole natural cork that has been traditionally used. Steam treated for the reduction of TCA and other volatile compounds. MP TS is the ideal solution if you want to bottle your distillates using a traditional closure at an affordable rate.  19.2 mm cork diameter. Fits standard cork finish (neck) bottles & 375mL Farro spirit bottles. Italy produces more wine than any country in the world and Molinas is the largest Italian cork supplier with over 1 billion corks produced annually. Molinas Cork was started over 100 years ago by Pietro Molinas on the Italian island of Sardinia. Besides its beautiful beaches and designation as one of the world's five Blue Zones, Sardinia is known for its large, government protected Cork tree forests. Today, the 4th generation of the Molinas family sustainably harvests cork from these protected trees. Compared to most cork available in the market, the bark is allowed to mature an additional year. This leads to a less porous, higher quality cork, and has less impact on the forest. Throughout the entire process from tree to finished cork, quality control is strictly monitored. MoreFlavor! is proud to represent Molinas Cork in the USA Tolerances on Normal Dimensions: Height of the cork body: Nom. Value +/- 0,3 mm Diameter of the cork body: Nom. Value +/- 0,3 mm Height of the stud: Nom. Value +/- 0,2 mm Diameter of the stud: Nom. Value +/- 0,2 mm Characteristics Physical / Chemical / Sensory: Humidity: Min: 3% Max: 8% Peroxides: < 0,2 mg/stopper Dust transfer:  ≤ 1,5 mg/stopper Organoleptic test: ≤ 2% Final Treatments: Genesis Steam treatment for the reduction of TCA and of other volatile compounds. Washing: with a solution of H2O2. Drying: a forced warm air for the elimination of peroxides residuals silicone coating fit to food contact. Silicone lubricant and adhesives with food certification for food contact.    

Read more less

Bar Top T-corks offer the convenience of hand sealing, allowing you to easily reclose bottles  Synthetic cork stopper with black plastic head 19.5mm cork diameter | Fits standard cork finish (neck) wine bottles & 375mL Farro spirit bottles Our bar top stopper corks have a smooth, black plastic bar top. Bar top corks are intended to fit tightly to eliminate leaking and maintain freshness of product. You may need to use a rubber mallet to install a bar top cork on a container with matching neck finish. Easy to remove and reuse, bar top corks feature synthetic Expancork stems. Dimensions: 1.18" head diameter; 0.77" (19.5mm) cork diameter; 1.22" total height.

Read more less

Bar Top T-corks offer the convenience of hand sealing, allowing you to easily reclose bottles  Synthetic cork stopper with black beechwood head 22.6mm cork diameter | Fits 750mL Farro spirit bottles Bar top corks featuring beech wood heads will give finish your product with a touch of style. Bar top corks are intended to fit tightly to eliminate leaking and maintain freshness of product. You may need to use a rubber mallet to install a bar top cork on a container with matching neck finish. Easy to remove and reuse, bar top corks feature synthetic Expancork stems. Dimensions: 1.34" head diameter; 0.89" (22.6mm) cork diameter; 1.34" total height.

Read more less