Beer Making
-
BrewBuilt® X3 | Replacement Lid Clamp | 8" Tri-Clamp
Replacement clamp for the BrewBuilt X3 Uni Conical 8" tri-clamp lid. This 3-piece stainless steel tri-clamp features two hinges which makes the clamp easier to work with on larger fitting sizes.
$54.99
-
Brewtools MiniUni™ 50+ | Cooling Jacket | 50L | 13.2G
The Brewtools MiniUni™ series fermenters are high-quality, affordable and flexible tanks for fermentation, storage and serving beer The Plus models feature a built-in cooling jacket for maximum cooling power when paired with a glycol chiller Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use Pressure rated to 30 PSI so you can safely ferment under pressure and pressure transfer finished beer to kegs with virtually no oxygen pickup Brewtools is a Norwegian brand known for high-quality products made without compromise. From brewing systems to fermenters, they continue to push the envelope of innovation for homebrewers around the globe All valves, fittings, and gaskets come included The MiniUni™ is a series of high-quality, affordable and flexible tanks for fermentation, storage and serving beer and endless other applications like water heating, cleaning liquid storage, HERMS setups, etc. The Plus-model also has a cooling jacket with 3/8" NPT threaded ports and two 1.5" T.C. ports in the front. They can be kept in the included base, or installed on the wall with the included wall bracket. With the optional pressure kit, you can utilize the 2 bar (30 PSI) pressure rating for fermentation and carbonation. Use them to build your setup, they will last a lifetime! And as always, Brewtools appreciates any feedback or requests for accessories. Key Features: PureBlast™ surface inside and out which eliminates the use of wax and polishing compounds and does not require passivation Easy cleaning with a 4" T.C. top port and 2" T.C. bottom port Pressure rated for 2 bar / 30 PSI. Wall bracket included Cooling jacket with 3/8" NPT ports Two 1.5" T.C. ports If you want to raise the MiniUni base and make room for an elbow with a butterfly valve or other accessories, check out the MiniUni™ Leg Kit. MiniUni tanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party. Specifications: Packaging size: 13.3" (w) x 13.7" (d) x 42.9" (h) Net weight: 45.6 lbs Gross weight: 48.9 lbs Tank diameter (inside): Ø11" Max volume: 13.2 gal Cone volume: 0.4 gal Material: 1.5mm stainless steel (SS304) Operating pressure: 1.0 bar / 15 PSI Max pressure: 2 bar / 30 PSI In the Box: MiniUni™ Tank Base with silicone gasket Wall bracket and wall support Wall bracket safety pin Composite T.C. adapter 4" to 34mm Airlock, 3-piece with holder 4" tri-clamp 2" tri-clamp 1.5" tri-clamp (2) 2" T.C. blind cap 1.5" T.C. blind cap (2) T.C. gaskets For User Manuals and support, please follow this link to Brewtools Docs.
$801.00
-
Brewtools MiniUni™ 30+ | Cooling Jacket | 30L | 7.9G
The Brewtools MiniUni™ series fermenters are high-quality, affordable and flexible tanks for fermentation, storage and serving beer The Plus models feature a built-in cooling jacket for maximum cooling power when paired with a glycol chiller Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use Pressure rated to 30 PSI so you can safely ferment under pressure and pressure transfer finished beer to kegs with virtually no oxygen pickup Brewtools is a Norwegian brand known for high-quality products made without compromise. From brewing systems to fermenters, they continue to push the envelope of innovation for homebrewers around the globe All valves, fittings, and gaskets come included The MiniUni™ is a series of high-quality, affordable and flexible tanks for fermentation, storage and serving beer and endless other applications like water heating, cleaning liquid storage, HERMS setups, etc. The Plus-model also has a cooling jacket with 3/8" NPT threaded ports and two 1.5" T.C. ports in the front. They can be kept in the included base, or installed on the wall with the included wall bracket. With the optional pressure kit, you can utilize the 2 bar (30 PSI) pressure rating for fermentation and carbonation. Use them to build your setup, they will last a lifetime! And as always, Brewtools appreciates any feedback or requests for accessories. Key Features: PureBlast™ surface inside and out which eliminates the use of wax and polishing compounds and does not require passivation Easy cleaning with a 4" T.C. top port and 2" T.C. bottom port Pressure rated for 2 bar / 30 PSI. Wall bracket included Cooling jacket with 3/8" NPT ports Two 1.5" T.C. ports If you want to raise the MiniUni base and make room for an elbow with a butterfly valve or other accessories, check out the MiniUni™ Leg Kit. MiniUni tanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party. Specifications: Packaging size: 13.3" (w) x 13.7" (d) x 30.3" (h) Net weight: 31.3 lbs Gross weight: 34.8 lbs Tank diameter (inside): Ø11" Max volume: 7.9 gal Cone volume: 0.4 gal Material: 1.5mm stainless steel (SS304) Operating pressure: 1.0 bar / 15 PSI Max pressure: 2 bar / 30 PSI In the Box: MiniUni™ Tank Base with silicone gasket Wall bracket and wall support Wall bracket safety pin Composite T.C. adapter 4" to 34mm Airlock, 3-piece with holder 4" tri-clamp 2" tri-clamp 1.5" tri-clamp (2) 2" T.C. blind cap 1.5" T.C. blind cap (2) T.C. gaskets For User Manuals and support, please follow this link to Brewtools Docs.
$653.00
-
Brewtools Troll Module Connection Kit
Bolt kit for connecting Troll Brew Table System modules together. M8 Bolt Kit 85mm, Hex 5, 4 pcs.
$9.00
-
Brewtools Troll Frame With Plate
Low frame with wheels and flat top plate for Brewtools Troll Brew Table System. Used for placing equipment like glycol chillers or handling malt when using the crane. Remember M8 bolt kit for connecting to other modules. Troll Frame With Plate only. Does not include Troll Table pictured in example photo. Specifications: Size: 28.75" x 28.75" x 5.9" (assembled) Weight assembled: 37.5 lbs Material: AISI 304 In the box: 1 pcs table frame, 28.75" x 28.75" 1 pcs flat top plate with hole 2 pcs wheels with brakes 2 pcs wheels without brakes 4 pcs 20-pack silicone plugs for holes Tools and bolts for assembly
$365.00
-
Brewtools Troll Bracket for Counterflow Cooler
Bracket for installing Brewtools counterflow cooler under the Troll Brew Table. Tools and bolts included.
$38.00
-
Brewtools Troll Unitank Frame
Low frame with wheels for installing Brewtools Unitanks in the Troll Brew Table System. Fits all Brewtools Unitanks up to and including the F300 Unitank. Includes bolts and nylon spacers for Unitank installation. Remember M8 bolt kit for connecting to other modules. Specifications: Size: 28.75" x 28.75" x 5.9" (assembled) Weight assembled: 22 lbs Material: AISI 304 In the box: 1 pcs unitank frame, 28.75" x 28.75" 2 pcs wheels with brakes 2 pcs wheels without brakes 4 pcs nylon spacers and M10 bolts for Unitank 4 pcs 20-pack silicone plugs for holes Tools and bolts for assembly
$293.00
-
Brewtools Troll Brewing Crane
The perfect match for the Brewtools Troll Brew Table 220 lb lifting capacity Height adjustable (6 levels) Flexible lifting bracket Flexible pulley placement on boom PureBlast™ surface The Brew Crane allows you to easily lift and swing the malt pipe of the Brewtools Brewing System. The Troll Table comes ready for the crane to be installed. The crane can lift 220 lbs. A universal lifting bracket is included. It is possible to use the crane without the Troll Brew Tables at your own risk. The hole needed for the bushings is 64mm. Specifications: Ceiling height requirement: 72.6" to 92.3" Height requirement is based on model of brewing system you have For more detailed specs, please follow this link to Brewtools Docs Lifting height above table top: 39.75" to 59.5" Weight assembled: 29 lbs Material: AISI 304 In the box: Crane, 3parts Lifting bracket Bottom support Winch bracket Winch Support leg with adjustable foot (2) S-hooks Nylon pulleys and bushings Tools and bolts for assembly Brewtools Troll Table sold separately Note: The maximum weight must never been exceeded. Crane must only be used with support legs or a low frame bolted to the side you lift towards. For User Manuals and support, please follow this link to Brewtools Docs.
$420.00
-
Brewtools Troll Brew Table | Low Model | 59cm | 23"
Modular design with the possibility to bolt several frames together Strong 1.5" x 1.5" square frame construction PureBlast™ surface Ready for Troll Brew Crane High quality wheels, 2 of which have brakes The Brewtools Troll Brew Table System is a result of years of development. Brewtools worked hard to keep this simple, modular and flexible, and futureproof for accessories and add-ons. The optional Troll Brew Crane will give you the possibility to handle malt pipes with ease. Specifications: Size: 28.75" x 28.75" x 23.25" (assembled) Weight assembled: 59.5 lbs Material: AISI 304 In the box: (2) table frames, 28.75" x 28.75" (4) legs (15.75") (1) top plate with folded edges (5) silicone strip to raise top plate above corner bolts (2) wheels with brakes (2) wheels without brakes (4) 20-pack silicone plugs for holes Tools and bolts for assembly
$695.00
-
Brewtools Troll Brew Table | Tall Model | 89cm | 35"
Modular design with the possibility to bolt several frames together Strong 1.5" x 1.5" square frame construction PureBlast™ surface Ready for Troll Brew Crane High quality wheels, 2 of which have brakes The Brewtools Troll Brew Table System is a result of years of development. Brewtools worked hard to keep this simple, modular and flexible, and futureproof for accessories and add-ons. The optional Troll Brew Crane will give you the possibility to handle malt pipes with ease. Specifications: Size: 28.75" x 28.75" x 35" (assembled) Weight assembled: 63.9 lbs Material: AISI 304 In the box: (2) table frames, 28.75" x 28.75" (4) legs (27.5") (1) top plate with folded edges (5) silicone strip to raise top plate above corner bolts (2) wheels with brakes (2) wheels without brakes (4) 20-pack silicone plugs for holes Tools and bolts for assembly
$724.00
-
Fermentis | SafAle™ F-2 Bottle Conditioning | Dry Beer Yeast | 25 g
F-2 was specifically selected for secondary fermentation in bottle and in cask Neutral aroma profile and high alcohol resistance make it perfect for refermentation bottle conditioning Sticks well at the bottom of the bottles/casks Fermentis active dry yeast offers reliability, ease-of-use, and consistency to home and professional beverage makers across the world SafAle™ F-2 is specifically selected for secondary fermentation in bottle and in cask. This yeast assimilates very little maltotriose but assimilates basic sugars (glucose, fructose, saccharose, maltose) and is characterized by a neutral aroma profile respecting the base beer character. Its neutral aroma profile, high alcohol resistance and stickiness characteristics make it a perfect match for consistent re-fermentation in bottle and cask. SafAle™ F-2 resists to high alcohol levels (>10% v/v) and allows brewers to obtain all the properties of refermentation such as: Beer preservation thanks to oxygen trapping Contribution in roundness and maturation aromas Carbonation Sticks well at the bottom of the bottles/casks and forms a nice haze when it is resuspended Usage: Add 19 to 38 grams of sugar per gallon of beer (5 to 10 grams of sugar per liter) to obtain a saturation of 2.5 to 5.0 g/l of CO2 Pitch the sweetened beer, that should be at fermentation temperature (68-77°F / 20-25°C) with the rehydrated yeast. Carbonation will be achieved in 1 to 2 weeks at 68-77°F. Carbonation at 59°F can take over 2 weeks At the end of refermentation, the beer can be cooled down and will gain in roundness after 2 to 3 weeks Please note: Example image shows a 20g sachet. The correct size is 25g. Updated image coming soon.
$7.49
-
BrewZilla | Replacement Malt Pipe Handle | 65L
Replacement malt pipe handle for the 65L BrewZilla. 3/8" thick. KegLand Part Number: KL29513
$16.49
-
RAPT Bluetooth Thermometer | Replacement HTC Probe
Replacement probe for the RAPT Bluetooth Thermometer (MT409). The cord is 39" long with a 7.8" long probe probe with sharp tip. Please remove the black plastic tip before use. That is for storage to avoid punctures / injury. KegLand Part Number: KL29445
$10.99
-
Stainless Steel Shuttle for NukaTap® Beer Faucet
This stainless steel shuttle can be used to replace the TPV rubber NukaShuttle that comes standard in the NukaTap beer faucet. For users that prefer stainless internal mechanisms in their faucet. You will need to remove the bonnet piece at the handle, pull the handle out and then slide the shuttle piece out. Compatible with all NukaTap faucets, including Gen 2 Flow Control. KegLand Part Number: KL35958
$5.49
-
Beer Faucet Shank | Pass Through | Stainless | 4"
You can use pass through shanks for beer entry through the back side of a cooler. Drill a 1" hole through the cooler, insert the shank, and use the two attached nuts to tighten up on the cooler. You will need nuts and nipples of the size line you are working with as well as hose clamps. We do not use pass through shanks in our boxes because we drill a hole that is same size as the line so we can pull it back in when we are traveling. However there might be instances where they would be appropriate. Pass through shanks can also be used to put through the side of a refrigerator to pass a gas line through Installation Note: On a fridge there is generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. This is a stainless steel shank with chrome plated brass hex nuts. Dimensions: 4" - Shank Length 4" - Thread Length 2-3/4" - Pass Through Length Max length with hex nuts at either end Does not account for nuts/nipples you may install Male Beer Thread (5/8" BSP)
$29.99
-
Beer Faucet Shank | Pass Through | Stainless | 3"
You can use pass through shanks for beer entry through the back side of a cooler. Drill a 1" hole through the cooler, insert the shank, and use the two attached nuts to tighten up on the cooler. You will need nuts and nipples of the size line you are working with as well as hose clamps. We do not use pass through shanks in our boxes because we drill a hole that is same size as the line so we can pull it back in when we are traveling. However there might be instances where they would be appropriate. Pass through shanks can also be used to put through the side of a refrigerator to pass a gas line through. Installation Note: On a fridge there are generally no coolant lines running through the door but please check to see there are no lines connecting the door and the rest of the refrigerator. To test for coolant lines on a freezer start with a warm freezer then plug the unit in with the lid open. You should be able to see the lines form condensation on the inside of the freezer where there are lines running. Please still use caution when drilling. This is a stainless steel shank with chrome plated brass hex nuts. Dimensions: 3" - Shank Length 3" - Thread Length 1-7/8" - Pass Through Length Max length with hex nuts at either end Does not account for nuts/nipples you may install Male Beer Thread (5/8" BSP)
$24.49
-
WilliamsWarn BrewKeg25 | Pressurizable Conical Fermenter | Draining Sediment Bottle | 25 L | 6.6 Gallon
The BrewKeg25 is a 6.6-gallon (25 L) capacity stainless steel, conical pressure fermenter with sediment removal and an easy to use lid with pressure relief valve. Suitable for batch sizes of up to 6.6 gallons, the BrewKeg25 is suitable for all-grain and extract brewers who want to experience the magic results of pressure fermentation. Ferment under pressure and serve 6.6 gallons of beer from the same vessel without ever transferring! The BrewKeg from WilliamsWarn is a unitank that allows you to ferment, carbonate and serve all in one vessel, saving you money on other equipment. The BrewKeg lets you ferment up to 6.6 gallons of wort at up to 25 psi. The tank itself has a total volume of 7.9 gal, giving it the perfect amount of headspace to produce 6 gallons of finished beer. Fermenting under pressure reduces esters allowing your beer to ferment at higher and more varied temperatures. Fermenting under pressure also produces clearer beer! The fermenter also includes a yeast collection ball so you can remove yeast and trub without having to rack to a separate vessel. The BrewKegs all stainless steel construction and conical bottom make it perfect for extract, partial extract, and all-grain brewers. Features: Made from stainless steel Conical base Extra-large, easy to remove draining sediment ball 25 psi working pressure & built in relief valve 40 psi maximum pressure rating Ferments clean and clear beer from 64-82°F Beer is carbonated perfectly at the end of fermentation Beer ready to enjoy sooner Compact design fits in most kegerators Eliminates kegging Easy to clean and sanitize Dimensions: Height: 26 in. Diameter: 15.5 in. Actual Volume: 30L (7.92 gal)
$659.99
-
BrewZilla Gen 4 | RAPT Screen Extension Cable | 5 ft.
RAPT Controller extension cable for the BrewZilla 35L, 65L and 100L Generation 4 models. Mount your screen up higher in your brew space and get a clear view on brew day. Compatible with 110V / 220V models 4.9 ft. Cable Length (1.5 m) Suitable only for Gen 4 BrewZillas KegLand Part Number: KL32681
$21.99
-
BrewZilla Gen 4 | RAPT Controller Swivel Mounting Bracket
Controller mounting bracket for the Gen 4 BrewZillas. Mount your controller up to 5 ft. away with the RAPT Screen Extension Cable (AG547). KegLand Part Number: KL32698
$21.99
-
Brewtools MiniUni™ Leg Kit
Kit with 3 legs and necessary accessories to raise the MiniUni base and make room for an elbow with a butterfly valve or a heating element etc. Made from reinforced nylon. With the legs mounted, the height will increase with 5.5". As the legs extends with the same angle as the base, space equivalent of a circle of 14.5" in diameter is needed where placed. In the box: 3 pcs legs 6 pcs silicone plugs 3 pcs M6 bolts Tool for assembly (Hex 5mm)
$42.00
-
Five Star | Lactic Acid (88%)
88% concentration. Use to adjust pH of sparge water down.
$220.99
-
Five Star | Kettle Defoamer 880 | 1 Gal | Case of 4
Non-silicone, antifoam agent best used in blow-off buckets. Use as a rate of 1 oz per BBL. This will provide foam surpression for up to 14 days Use at a rate no greater than 1 oz per 5 BBL With blow-off buckets, add as needed. Generally 1 oz. per 30 gallons of foam Are you a Pro Brewer or a brewery in planing? For the best price on commercial brewery supplies, sign up for an account at morebeerpro.com!
$288.99
-
KOMOS® | Stainless Splicer | 1/4" Barb x 3/8" Barb
Stainless steel splicer fitting for joining different sizes of tubing. Recommended for splicing 3/16" or 1/4" ID tubing to 3/8" ID tubing. One end is slightly undersized at 6 mm (0.24") and the other is slightly oversized at 10 mm (0.39"). Made from 304 stainless steel.
$4.39
-
Replacement Transformer for BrewBuilt® IceMaster Max 2
Replacement Transformer for BrewBuilt® IceMaster Max 2 glycol chiller.
$39.99
-
NukaTap® Mini Beer Faucet | Stout Spout
The Stout Spout installs on the NukaTap Mini to improve the pour of your stouts and nitro brews The creamer/aerator disc inside strips out nitrogen gas for a creamier beer Simply unthread the standard spout from the NukaTap Mini and swap in the Stout Spout Simply unscrew the normal spout from the NukaTap Mini and screw this Stout Spout in its place to pour your nitro brews. This spout has a creamer/aerator disc inside that strips out the nitrogen gas for a creamier beer. Only compatible with the NukaTap Mini faucet. The Stout Spout will have a 1/4" female flare thread. KegLand Part Number: KL32858
$8.79
-
KegLand Quick Swivel Connector | Stainless End Cap | 18mm Diameter
The fitting is to be used in a KegLand Stainless Steel Quick Swivel Connectors in 1/2" Female NPT. This is the end cap only. Handy for terminating 1/2" Quick Swivel Connections. KegLand Part Number: KL31646
$2.19
-
KegLand Quick Swivel Connector | Replacement O-rings | 10-Pack
Replacement O-rings for the 1/2" KegLand Quick Swivel Connectors. Made from high temp silicone. Comes in a pack of 10. These come in brown silicone only. Refrain from using undiluted acidic / heavy strength alkaline substances or the Silicone may change in color. KegLand Part Number: KL31592
$2.19
-
KegLand Quick Swivel Connector | 1/2" Nut
Replacement 1/2" KegLand Quick Swivel Connector Nut. Comes with a heavy duty silicone grip guard allowing comfortable and quick tool-free operation. Silicone O-ring included. KegLand Part Number: KL31547
$4.99
-
KegLand Quick Swivel Connector | 1/4" Straight Barb | 6.35 mm Duotight Compatible
This straight barb in 1/4" (6.35mm) OD is only compatible with the 1/2" KegLand Quick Swivel Connector Nut. Compatible with 6.35 mm Duotight fittings. Quick Swivel Nut sold separately. KegLand Part Number: KL31554
$3.99
-
KegLand Quick Swivel Connector | 5/16" Straight Barb | 8 mm Duotight Compatible
This straight barb in 5/16" (8mm) OD is only compatible with the 1/2" KegLand Quick Swivel Connector Nut. Compatible with 8 mm Duotight fittings. Quick Swivel Nut sold separately. KegLand Part Number: KL31561
$3.99
-
KegLand Quick Swivel Connector | 3/8" Straight Barb | 9.5 mm Duotight Compatible
This straight barb in 3/8" (9.5mm) OD is only compatible with the 1/2" KegLand Quick Swivel Connector Nut. Compatible with 9.5 mm Duotight fittings. Quick Swivel Nut sold separately. KegLand Part Number: KL31578
$3.99
-
KegLand Quick Swivel Connector | 1/2" Straight Barb
This straight barb in 1/2" (13mm) OD is only compatible with the 1/2" KegLand Quick Connector Swivel Nut. 3/8" (10mm) ID bore. Quick Swivel Nut sold separately. KegLand Part Number: KL31585
$3.99
-
KegLand Quick Swivel Connector | 1/2" x 1/4" Elbow Barb | 6.35 mm Duotight Compatible
High temp silicone grip provides a cool touch even with hot liquids! Ribbed grips allow quick comfortable tool-free operation Fits all male 1/2" NPT and BSP fittings 6.35 mm Duotight compatible stainless steel elbow barb tail The KegLand Stainless Steel Quick Connectors come with a heavy-duty silicone grip guard allowing comfortable and quick tool-free operation. Specs: Stainless steel and silicone construction Silicone O-ring seal is retained for perfect positioning but is easily cleaned or replaced 1/4" (6.35mm) OD elbow barb tail KegLand Part Number: KL31677
$8.79
-
KegLand Quick Swivel Connector | 1/2" x 1/4" Straight Barb | 6.35 mm Duotight Compatible
High temp silicone grip provides a cool touch even with hot liquids! Ribbed grips allow quick comfortable tool-free operation Fits all male 1/2" NPT and BSP fittings 6.35 mm Duotight compatible stainless steel barb tail The KegLand Stainless Steel Quick Connectors come with a heavy-duty silicone grip guard allowing comfortable and quick tool-free operation. Specs: Stainless steel and silicone construction Silicone O-ring seal is retained for perfect positioning but is easily cleaned or replaced 1/4" (6.35mm) OD barb tail KegLand Part Number: KL31608
$8.79
-
KegLand Quick Swivel Connector | 1/2" x 3/8" Straight Barb | 9.5 mm Duotight Compatible
High temp silicone grip provides a cool touch even with hot liquids! Ribbed grips allow quick comfortable tool-free operation Fits all male 1/2" NPT and BSP fittings 9.5 mm Duotight compatible stainless steel barb tail The KegLand Stainless Steel Quick Connectors come with a heavy-duty silicone grip guard allowing comfortable and quick tool-free operation. Specs: Stainless steel and silicone construction Silicone O-ring seal is retained for perfect positioning but is easily cleaned or replaced 3/8" (9.5mm) OD barb tail KegLand Part Number: KL31622
$8.79
-
KegLand Quick Swivel Connector | 1/2" Elbow Barb
This elbow barb makes it easier to route lines and avoid kinks in your tubing. Commonly used for pump inlet/outlets, fermenter blowoffs, or gravity fed transfer lines. Quick Swivel Nut sold separately. Specs: 1/2" (13mm) OD x 1/2" Quick Swivel Nut compatible end Stainless steel KegLand Part Number: KL31660
$7.69
-
Ss Brewtech | Ss Hop Spider
Keeping trub and hop material in your kettle and out of your fermenter is one of the critical components to ensuring clear beer in your pint glass! On top of that, brewing with whole cone hops can introduce a lot of hop leaf material that easily overwhelms and clogs transfer lines creating lots of headaches. Ss Hop Spider helps with these challenges by containing hop material within a fine mesh, photo-chemical etched basket. The basket sits inside a custom-designed ring mount with Silicone Adjustment Arms so you can dial in the Hop Spider for the perfect fit on your kettle. Intended for use with SVBS, Ss Brewtech TC Brew Kettles(10 gal, 15 gal & 20 gal), and Ss Brewtech eKettles. Not compatible with Ss Brewtech 30 gal & 50 gal Brew Kettles and Ss Brewtech 5.5 gal Mini Brew Kettle. Features: 400 Micron Photo-Chemical Etching Adjustable Mounting Arm Removable Basket for Easy Cleaning Specifications: 304 Stainless Steel and High Temp Silicone 6” Basket Diameter 15.5” Basket Height 15" Adjustment Arm Minimum Length 18" Adjustment Arm Maximum Length Package Dimensions: 11"H x 9.5"W x 19"L 6lbs
$99.95
-
KegLand Handy Clamp for BrewZilla | Tubing Clamp | 4" Long
Secure silicone hose to your mash tun during recirculation Large circular center of the clamp leaves room for tubing without pinching Excellent chemical resistance to common brewing cleaners and sanitizers Able to withstand boiling temperatures This handy spring clamp features a heavy-duty muslin spring which ensures your silicone hose never accidentally pops out of your mash tun and spills your precious nectar over your brewery floor. The large circular space between the arms of the clamp is perfect for passing 1/2" silicone tubing through without pinching. Rounded handles for a comfortable grip and a PE end grip to ensure your hosing is kept secure. Made from Polypropylene and Polyethylene which have good chemical resistance so it will stand up to the task for use around common brewing cleaners and sanitizers. Temperature Rating: 32-248°F KegLand Part Number: KL24686
$3.99
-
NukaTap® Mini Beer Faucet | Wall Mount Shank Kit | 6.35 mm Duotight
Designed specifically for mounting the NukaTap Mini Beer Faucet on any kegerator, keezer, cold room wall, or other flat surface Connect beer line directly to the faucet, reducing the amount of temperature loss to a standard draft shank No spinning faucets. Your tap will remain in a fixed orientation once locked into the collet Easy installation. No need to drill a large hole through your fridge to accommodate a standard 5/8" draft shank Use with 6.35 mm OD EVABarrier draft tubing This shank kit is specifically designed to suit the NukaTap Mini Beer Faucet and will allow you to connect the NukaTap Mini to a cooler box, kegerator, keg fridge, cold room wall or any other flat surface. This wall mount shank kit is for use with 6.35 mm OD EVABarrier. For the shank kit for use with 8 mm OD EVABarrier, see here. New Innovative Shank Design Unlike other shank kits, this kit doesn't use a bulky 5/8" threaded shank. The issue with a standard draft shank is that acts as a heat sink, and due to the fact that most shanks sit inside an insulated wall, this results in a substantial amount of warm beer coming out of the tap before cold beer starts flowing. This results in substantial "first pour foam" effect which wastes beer, can result in sour beer, and ultimately negatively effects the quality of the beverages being served. This new design has the beer line feed all the way directly up to the back of the faucet, greatly reducing the volume of non-refrigerated beer. No Spinning Shanks If you have ever installed a traditional 5/8" long shank, you will know how frustrating it is when you use the faucet and it starts rotating. This new design of shank alternative uses three screws that lock the tap into a fixed position and prevents the taps from rotating. If you loosen the 1/2" stainless tap collet you can still have the flexibility to rotate the faucet to any orientation, but once the collet is tight, interlocking teeth on this shank kit and the NukaTap Mini will hold the tap permanently in the correct orientation. Easy Installation Another advantage compared to standard shanks is that this kit doesn't require you to drill a large 3/4"-1" hole through the wall. As no shank is required, only a hole large enough to accommodate the beer line is required. As a result, an 8mm (5/16") conventional drill bit is all that is necessary for installation. However, if you are concerned about the small amount of beer sitting in the draft line inside the wall not being refrigerated, you can also shell out a larger diameter of foam on the inside of the wall to allow cold air to circulate around the beer line thus reducing the non-refrigerated beer in the line even more. If you wanted to do this the Step Drill Bit is the best tool for the job. Any Wall Thickness Other shank kits will require you to purchase a specific length shank for a specific wall thickness. This new shank alternative will fit any wall thickness. If you have wall thicknesses that are less than 2.7" thick then you can use the included screws that have "snap off" points so you can simply cut the screws down to the desired length. However, if the wall is thicker than 2.7" you can simply purchase a conventional screw from the hardware store and screw the shank kit to your wall. If the substrate is firm enough you may not even need to go all the way through the wall so a common 1-1/4" long screw may be all that is required. Specifications: Beer Line Diameter: 6.35 mm OD EVABarrier Collet and Screw Cover: 304 Grade Stainless Steel O-ring Material: Dual O-ring Silicone/EPDM combination Plastic Mounting: Polyketone (POK) Temperature Range: 14-212°F (-10-100°C) Max Pressure: 150 psi KegLand Part Number: KL32193
$21.99
-
NukaTap® Mini Beer Faucet | Wall Mount Shank Kit | 8 mm Duotight
Designed specifically for mounting the NukaTap Mini Beer Faucet on any kegerator, keezer, cold room wall, or other flat surface Connect beer line directly to the faucet, reducing the amount of temperature loss to a standard draft shank No spinning faucets. Your tap will remain in a fixed orientation once locked into the collet Easy installation. No need to drill a large hole through your fridge to accommodate a standard 5/8" draft shank Use with 8 mm OD EVABarrier draft tubing This shank kit is specifically designed to suit the NukaTap Mini Beer Faucet and will allow you to connect the NukaTap Mini to a cooler box, kegerator, keg fridge, cold room wall or any other flat surface. This wall mount shank kit is for use with 8 mm OD EVABarrier. For the shank kit for use with 6.35 mm OD EVABarrier, see here. New Innovative Shank Design Unlike other shank kits, this kit doesn't use a bulky 5/8" threaded shank. The issue with a standard draft shank is that acts as a heat sink, and due to the fact that most shanks sit inside an insulated wall, this results in a substantial amount of warm beer coming out of the tap before cold beer starts flowing. This results in substantial "first pour foam" effect which wastes beer, can result in sour beer, and ultimately negatively effects the quality of the beverages being served. This new design has the beer line feed all the way directly up to the back of the faucet, greatly reducing the volume of non-refrigerated beer. No Spinning Shanks If you have ever installed a traditional 5/8" long shank, you will know how frustrating it is when you use the faucet and it starts rotating. This new design of shank alternative uses three screws that lock the tap into a fixed position and prevents the taps from rotating. If you loosen the 1/2" stainless tap collet you can still have the flexibility to rotate the faucet to any orientation, but once the collet is tight, interlocking teeth on this shank kit and the NukaTap Mini will hold the tap permanently in the correct orientation. Easy Installation Another advantage compared to standard shanks is that this kit doesn't require you to drill a large 3/4"-1" hole through the wall. As no shank is required, only a hole large enough to accommodate the beer line is required. As a result, an 8mm (5/16") conventional drill bit is all that is necessary for installation. However, if you are concerned about the small amount of beer sitting in the draft line inside the wall not being refrigerated, you can also shell out a larger diameter of foam on the inside of the wall to allow cold air to circulate around the beer line thus reducing the non-refrigerated beer in the line even more. If you wanted to do this the Step Drill Bit is the best tool for the job. Any Wall Thickness Other shank kits will require you to purchase a specific length shank for a specific wall thickness. This new shank alternative will fit any wall thickness. If you have wall thicknesses that are less than 2.7" thick then you can use the included screws that have "snap off" points so you can simply cut the screws down to the desired length. However, if the wall is thicker than 2.7" you can simply purchase a conventional screw from the hardware store and screw the shank kit to your wall. If the substrate is firm enough you may not even need to go all the way through the wall so a common 1-1/4" long screw may be all that is required. Specifications: Beer Line Diameter: 8 mm OD EVABarrier Collet and Screw Cover: 304 Grade Stainless Steel O-ring Material: Dual O-ring Silicone/EPDM combination Plastic Mounting: Polyketone (POK) Temperature Range: 14-212°F (-10-100°C) Max Pressure: 150 psi KegLand Part Number: KL32186
$21.99
-
NukaTap® Mini Beer Faucet | Duotight Adapter | 8 mm (5/16")
This Duotight 8 mm (5/16") adapter is designed to suit the Nukatap Mini and will allow you to couple the faucet to a wide range of other 8 mm Duotight fittings. This includes attaching it to the Duotight Flow Control Ball Lock Disconnect. This particular type of flow control ball lock disconnect includes a "tang" at the top of the push in fitting that couples with this adapter. The combination of the two fittings prevents the faucet from spinning around while in use. Sold Separately: NukaTap Mini Beer Faucet (D1598) Flow Control Ball Lock Disconnect (DUO159) Mini Self Closing Spring (D1598A) KegLand Part Number: KL32209
$7.69
-
NukaTap® Mini Beer Faucet | Matte Black | Forward Sealing
The ultimate portable draft faucet! Compact & lightweight with all the advantages of a standard NukaTap forward sealing faucet Pair with a Flow Control Ball Lock QD & Duotight Adapter and the whole assembly fits in your pocket Forward-sealing design prevents beer residue from gumming up the faucet Reduced first pour foam due to low thermal mass and conductivity Perfect for mobile draft, mini kegs, sampling from fermenters, and can even be installed on your kegerator or keezer Mini Design – Ideal Flow Rate for Small Systems Most conventional beer faucets are designed with 3/8" diameter spouts so you can pour a pint in just over 10 seconds. This type of flow rate is great for high turnover bars and commercial venues but isn't necessary or even desirable for all applications. For compact portable systems and home draft systems, a slower flow rate is easier to control and further reduces foaming issues due to the low liquid volume stored in the body of the faucet. The NukaTap Mini is also more ideal for pouring smaller doses. For example, cocktails where 5-8 oz of liquid is dispensed is difficult to control with a high flow rate tap. For portable systems, the NukaTap Mini with the Flow Control Ball Lock QD & Duotight Adapter assembly is small enough to literally put in your pocket, making it ideal for mini keg setups that you want to be portable or that you want to easily fit inside a domestic fridge where space is tight. Forward Sealing Forward sealing faucets are absolutely the way to go when it comes to beer taps. Old legacy taps still exist in the industry that are simply poorly designed. The issue with rear sealing faucets is that beer dries up on the internal piston. Aside from being unsanitary, as more and more beer dries up in these components the faucet can almost glue completely shut causing damaged seals or broken handles (this is particularly the case if it's left for some time to dry out with beer inside). These older legacy designs still exist probably due to poor education. The forward sealing designs do not have this problem and the tap drains out completely with no beer drying up on the mechanical moving parts in the same way. This makes the tap more sanitary and reduces maintenance. In many instances the price is similar so there is no reason to use a poorly designed rear sealing faucet. All NukaTap faucets are forward sealing. Laminar Flow Just like the NukaTap SS and NukaTap FC, the NukaTap Mini has been designed with laminar flow in mind. Laminar flow is critical for a beer tap as it means you will pour the beer with minimal foaming and a substantial reduction in wastage. Think about how many times a beer faucet opens and closes in its lifetime. 1,000 or maybe 10,000 times? Laminar flow saves wasted beer in excessive foam and the better laminar flow easily pays for itself in a reduction in lost beer. To use poorer designed faucets is essentially flushing money down the sink. Extensive modeling has been done on the NukaTap design to improve laminar flow. Integrated Seals That Are Indestructible and More Sanitary Unlike other designs, the NukaTap Mini body is made from Polyketone (POK) making it strong, robust, and able to be autoclaved. The seals are also over-molded from Santoprene® making them hard wearing so they will literally last for the lifetime of the tap without the need for replacement. Santoprene® and POK both have excellent resistance to chemicals such as caustic soda, peroxide, phosphoric acid, lactic acid, citric acid, acetic acid, and all common chemicals sold and used in the beverage industry. The seals internally are over-molded meaning no fissures or cracks exist for bacteria, crud, or yeast to hide. Superior First Pour Foam Due to Low Thermal Mass and Conductivity First pour foam is an issue caused by a warm tap body. For most faucets to pour well it's important to dispense enough beer to cool the tap body down to reach maximum performance. In addition to this the conductivity of the tab body also makes this worse so insulative materials simply work better than conductive materials. The NukaTap mini not only has very low thermal mass but is also highly insulative being made mostly from Santoprene® and POK. The combination of these two factors in conjunction with superior laminar flow makes for the lowest "first pour foam" effect out of any tap ever produced. Long Shank Alternative Most conventional beer faucets require a large 3/4" hole to be drilled through the side of your refrigerator, keezer, or cold box wall. Traditional long shanks also generally have a large volume of liquid that sits inside the wall unrefrigerated which is not ideal. New long shank alternatives developed for the NukaTap Mini are designed to suit any wall thickness and greatly reduces the stagnant beer sitting in the shank itself. For walls up to 2.7" thick, these wall mount shank kits include three screws, however if the wall is thicker, you can also use 6 small wood screws or something similar and attach three screws from the front and 3 from the back allowing you to go into any wall type. Another advantage of this new design is the tap will never accidentally rotate. Typically, other long shank beer taps rely on the hex nut on the shank to be done up tight enough to prevent rotation but if the wall compresses (often the case with foam walls) the tap is allowed to rotate. This new design has three fixing points making it impossible for the tap to rotate accidentally as the interlocking teeth behind the collet allow you to set the angle and then do up the collet to fix the tap permanently in that position. NukaTap Mini Accessories (Sold Separately): Duotight Flow Control Ball Lock QD (DUO159) Mini Self Closing Spring (D1598A) Duotight Adapter - 8mm (D1598B) Long Shank Alternative for Wall Mounting - Duotight 8mm (D1598C) Long Shank Alternative for Wall Mounting - Duotight 6.35mm (D1598D) Stout Spout (D1598E) Vertical Clamp On Assembly (D1598G) Horizontal Clamp On Assembly (D1598H)
$21.99
-
KOMOS® Deluxe Kegerator | Stainless Steel Exterior | Digital Thermostat | Casters | Regulator | Fits 1 Half Barrel Keg or 4 Corny Kegs | No Tower
The KOMOS Deluxe Kegerator model boasts the same features as the standard model with an eye-catching stainless steel extrerior and upgraded stainless steel drip tray. The interior is designed to fit up to four 5-gallon ball lock kegs at one time. This unit represents an amazing value in home draft dispensing. It features a digital controller, stainless door and exterior, aluminum floor, rolling casters, robust KOMOS CO2 regulator, and more. This version does not include a tower kit. Great as a fermenation refrigerator or as a unit that can be built-in when adequate ventilation is an option. Approximately 4" of space on each side of the kegerator is required to allow the unit enough air. The tower is then mounted to the countertop and often a pvc collar or foam insulation is placed between the kegerator and the counter. This can also be done with any of our regular kegerators by removing the tower from the unit and mounting it on the counter. The most eye-catching difference between this unit and the previous model is definitely the capacity. This is the first kegerator we have offered that can fit up to four 5-gallon homebrew kegs at one time, and that’s all thanks to the redesigned interior. Most kegerators position the compressor on the right or left side of the inside floor, making one side shallower than the other. The KOMOS kegerator positions the compressor in the middle so both sides of the interior have an equal depth. This seemingly small detail allows the unit to hold up to four 5-gallon Slimline Torpedo or Ball Lock Corny kegs. Dual gas line inlets are absolutely clutch if you want to serve beverages at two different pressures or use two different types of gas. The previous model had one inlet that was only wide enough for a single line to pass through. Now both inlets are just over 3/4" in diameter and feature PCO 1881 threads. This threading allows you to use the plastic Carbonation Ball Lock Cap (FE13) as a quick connect option for your gas lines. Improvements to the condenser, evaporator, and insulation means the KOMOS kegerator is more efficient than ever before. It also features a redesigned internal fan for improved air circulation, pulling cold air from below the evaporator and blowing it back over the top of your kegs and up into the tower to chill your draft lines. Extra Wide Temperature Range is Perfect for Homebrewers The KOMOS kegerator is tailored to a homebrewer's needs. Take, for example, the extended range digital controller with an adjustable temperature range from 26 - 82°F. This allows homebrewers to use as fermentation chamber and is something that other kegerators don't do. Although the unit does not provide heating, the extended range allows you to program the internal temperature at say an ale fermentation temp of 68°F and will provide cooling whenever the temp rises above that set point. With the insulation provided by the kegerator, heating should rarely be needed, but you can always place a low wattage heat wrap inside the unit if ever needed. The digital controller always displays the temperature and is easily adjusted from the front of the kegerator with the door closed. It's pretty nice. Added Features One of the unique features on a kegerator in this price range is the tower fan, which blows cold air up into your tower to reduce foaming issues. They also come standard with the KOMOS dual gauge CO2 regulator, which is super beefy and consistent in delivering accurate pressures. Most Chinese-made regulators experience creep where the pressure increases over time. The KOMOS regulator is by far the best CO2 regulator we have seen made in China. The countertop drip tray couldn't be easier to keep clean. Built-in drip trays look cool, but they're a pain to keep clean. Before long they get pretty disgusting with dried, spilled beer -- attracting fruit flies and becoming a haven for mold and bacteria to grow. They'll often overflow the reservoir inside the kegerator causing a huge mess. Our kegerator's tray is designed to be removed and easily washed. Best Value & Backed by MoreBeer! We've looked around, and when you factor in fast and free shipping, you are getting the very best value on a kegerator in the USA. Plus you're getting MoreBeer! service if something happens in shipment. We double box the unit with foam pads and have very little shipping damage. However, it will be delivered via Fed-Ex ground so damage is possible. If your unit arrives damaged just call us up and we will work with you to take care of it. Feature Summary: Digital Thermostat with wide 26 - 82° F temp range. Robust MKIII CO2 Regulator included Pre cut hole on top perfectly sized for 3" diameter tower CO2 Tank holder mounts on back of kegerator (tank not included) Efficient and powerful compressor Stainless steel door, top cover, and side panels Stainless Countertop Style Drip Tray Aluminum floor panel for additional keg support Rolling casters You will need to purchase keg connections depending on whether you are serving commercial sanke, ball lock corny, or pin lock corny Available Kegerator covers and "off road" casters for moving over uneven terrain. Specifications: 23.75" wide 25" deep 31.5" with CO2 mount 32.5" Tall 35" with Caster wheels 110 v - 60 hz 0.8 Amp draw Optimal ambient temperature is 65°F – 80°F CSA Certified Internal Dimensions: 19.5" wide 17" deep 16" down the center where compressor sits 28.5" tall What Fits: 5 Gal. Torpedo Keg - 3 5 Gal. Slimline Torpedo Keg - 4 5 Gal. Pin Lock Cornelius Keg (Corny Keg) - 3 5 Gal. Ball Lock Cornelius Keg (Corny Keg) - 4 5.2 Gal. Oxebar PET Keg - 3 5.16 Gal. Sixth Barrel Keg (Sixtel, Log) - 3 7.75 Gal. Quarter Barrel Keg (Pony Keg, Stubby Quarter) - 1 7.75 Gal. Slim Quarter Keg (Tall Quarter, The Slim) - 1 15.5 Gal. Half Barrel Keg (Full Size Keg) - 1 See below for the Kegerator Instruction Manual. (The Deluxe Kegerator does not have feauture a Guard Rail as seen in the residental kegerator instructions.) Please note: This unit requires 4" of clearance on all sides and is not intended to be installed under a countertop. For a build-in unit, see the KOMOS Pro Stainless Steel Kegerator.
$879.99
-
Rainbow Flavors | Strawberry Extract | Old Fashion Recipe | Soda Pop Base
Strawberry soda extract from Rainbow Flavors. Concentrated flavor extract for making your own sodas. Mix with water and sugar, then either carbonate by bottle conditioning with yeast, or force carbonate in a keg. One 2 fl oz bottle makes 4 gallons of soda. Recipes and mixing instructions for different size batches are included. One 1 gallon jug makes up to 256 gallons of soda.
$8.99
-
Briess CBW® Traditional Dark | Concentrated Brewers Wort | Liquid Malt Extract | LME | 30 SRM
Traditional Dark has an intense, sweet and malty flavor perfect for Brown Ales, Porters, Stouts, and other malt-forward styles Can be used as 100% of your fermentable sugar in extract brewing Add for color correction, boost gravity, or improve head retention in all grain brewing Briess Malt & Ingredients has had a focus on quality and innovation for more than 140 years, with all of their products being made in the U.S.A. Concentrated Brewers Wort (CBW) Liquid Malt Extract (LME) from Briess. Briess CBW malt extracts get all of their color and flavor from base and specialty malts, never through additional boiling. CBW malt extracts are unhopped and nondiastatic for flexible, creative brewing Traditional Dark LME: 100% pure malt barley extract made from a blend of 100% malts and water. Typical Analysis: Color (8° Plato): 30 SRM Fermentability: 75% Solids: 79%
$14.99
-
KOMOS® Homebrew Kegging Kit | Ball Lock Keg | Corny Keg | Premium Dual Gauge Regulator | Easy Push Connect Fittings
Due to high demand, the 2.5 gal is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory. A complete kegging system featuring KOMOS CO2 Regulator, KOMOS CO2 Cylinder, and a brand new ball lock corny keg! Available in 2.5 and 5 gallon sizes, we provide all the equipment you need to get your beer kegged up. Comes with EVABarrier tubing and Duotight ball lock QDs and fittings for easy assembly. Included: KOMOS Dual Gauge Regulator KOMOS 5 lb aluminum CO2 cylinder Ball Lock Corny Keg (2.5 or 5 gal) EVABarrier beer & gas lines Duotight ball lock quick disconnects (QDs) Duotight-compatible plastic picnic faucet KOMOS 7-in-1 Multi Tool Wrench Please note: the CO2 tank ships empty. It can be filled or swapped for a full tank at your local welding or homebrew supply store.
$309.99
-
Speidel Braumeister | Black Insulating Jacket | 50L
Help retain heat with Speidel's insulating jacket for the 50L Braumeister. Fits both new models as well as pre-2015 models.
$186.99
-
Brewtools | F300 Unitank | 32-76 Gallon Capacity | 120-290L
Ferment, cold crash, and carbonate beer all in one vessel with the Brewtools F-Series Unitank Cooling jacket welded to the vertical walls of the tank provide superior cooling capabilities compared to in-solution cooling coils Made from stainless steel throughout with Brewtools' proprietary PureBlast™ surface—no passivation required, simply rinse with warm water before your first use Pressure rated to 30 PSI so you can safely ferment under pressure and pressure transfer finished beer to kegs with virtually no oxygen pickup Brewtools is a Norwegian brand known for high-quality products made without compromise. From brewing systems to fermenters, they continue to push the envelope of innovation for homebrewers around the globe All valves, fittings, and gaskets come included Brewtools Unitanks are fermenters made for ambitious homebrewers and small breweries. As part of the Brewtools identity, they've explored new techniques and solutions. This has resulted in a series of high end fermentation tanks with new features and a lot of possibilities. Key Features: Brewtools PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation. Cooling jacket in the vertical walls offers efficient cooling without the hassle of cleaning a spiral. Many options for connecting accessories like sensors, heaters, carb. stones and other accessories. Pressure rated for 2 bar / 30 PSI Cooling jacket pressure rated for 0.5 bar / 7 PSI 8" TC port on top for easy access. 2" TC dump and racking valves. BrewTools Unitanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party. Specifications: Low height w/o acc.: 66.1" Max height w/o acc.: 74" Packaging size: 70.8" (h) x 28.3" (w) x 28.3" (d) Net weight: 167.1 lbs Gross weight: 209.4 lbs Tank diameter (inside): Ø23.6" Gross volume: 81.8 gal Max rec. volume: 76.6 gal Min rec. volume: 31.7 gal Volume, cone: 10.5 gal Material: 1.5mm stainless steel (SS304) Operating pressure: 1.0 bar / 15 PSI Max pressure: 2.0 bar / 30 PSI In the box: Unitank with adjustable frame 1 pcs Analog pressure gauge, TC34mm 2 pcs Butterfly-valve, 2" 1 pcs Butterfly-valve, 34mm DN20 1 pcs Blow-off pipe 1 pcs Racking arm 2" 1 pcs TC elbow 90°, 2" 1 pcs Insulation jacket, black neoprene 1 pcs Sample valve, 34mm 1 pcs TC Adapter 8"-4" 1 pcs TC blind cap, 4" 1 pcs TC blind cap 2" 2 pcs TC blind cap 1.5" 3 pcs TC blind cap 34mm 2 pcs TC gasket 8" lipped 2 pcs TC gasket 4" 2 pcs TC gasket 2" 5-pack 1 pcs TC gasket 1.5" 5-pack 3 pcs TC gasket 34mm 5-pack 1 pcs Tri Clamp 8" 1 pcs Tri Clamp 4" 5 pcs Tri Clamp 2" 2 pcs Tri Clamp 1.5" 10 pcs Tri Clamp 34mm 1 pcs TC tool 4 pcs M10 steel/rubber feet 1 pcs TC34mm safety valve (PRV, 2 bar) Necessary bolts and parts for assembly 5 year manufacturer's warranty Recommended accessories include: HopDrop-kit, Thermowells for your sensors, 34mm Ball-Lock gas adapter for CO2 filling, Coil for sample valve, Spunding valve, Hose barbs for filling and dumping, etc. For User Manuals and support, please follow this link to Brewtools Docs. NOTE: Model in photo is a prototype. Minor changes and improvements may occur.
$4,923.00
You have seen 1728 out of 3021 products