Search results for "din10 thermowell speidel tanks 6"

The FO-M tank from Speidel is very similar to the the standard FO style variable volume storage tank. The FO-M tank, however, has been specially altered to make it more useful as a fermentation tank, and comes pre-fitted with the most standard features equipped on tanks used for red fermentations. And they have the same degree of flexibility and customization available as the standard FO style tank, but offer an easy starting point and cost savings for tanks destined for red fermentation. And don't miss out on Spediel's Mobile Must Plunger, which makes punch downs fast, easy and automatic! Key Features Available in 28 sizes covering 6 different tank diameters from 1,100L to 15,200L Tank is equipped with rectangular manway for must discharge. Legs elevated to 52cm height for easier must discharge. Can be extended up to 80cm to accommodate a macro bin under the manway. Bottom drain is rotated to just in front of the left tank leg so it's out of the way of must receptacle. 1,100L & 1,600L Tanks equipped with 1.5" TC racking and drainage ports. All other tanks equipped with 2" TC. Larger fittings available by request Reinforced racking ports prevent tank wall flex and can support the weight of a tank mixer. All tanks include a lifting arm. Mobile, forkliftable Pneumatic Must Plunger available to go with these tanks! View the resource for more information on the key features of all Speidel Tanks. Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.

Read more less

The age-old, and still practiced, process of manual punch down is now modernized, automated and brought to a larger scale thanks to Speidel! This simple but effective system features an external  pneumatic cylinder which drives the punching assembly. During the downward stroke the folding stainless punching wings lay flat against the top of the pommace cap and push the solids back into the fermenting wine. On the upward stroke of the cycle the wings set at angle which induces the wings to rotate about 30 degrees, position themselves over a fresh segment of the cap, and the cycle then repeats itself. The whole cap can be punched in as little as 5-6 punch cycles—about 15 minutes! The duration of time that the tank performs punch downs, and the interval of time between them, are adjustable depending on your individual vineyard, vintage and winemaking style. Must Discharge: Automatic, motorized must-discharge arms with gate-style opening allows for fine netering of how fast you allow must to flow out of the tank. Especially useful with thin musts. Must-Discharge motor requires 380V, 3-phase power. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Tank ceiling is reinforced to withstand the punchdown forces. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Compressor should be able to provide 500L/min at 6 bar pressure with a minimum of 90L tank capacity (17.7 CFM at 87 psi with a 24 gallon tank). Speidel recommends that the compressed air be conditioned before entering the pneumatic cylinder and recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent. Air Consumption per punch cycle: Immersion Depth Air Consumption 1000 mm 12.3 liters 1250 mm 15.3 liters 1500 mm 18.3 liters 1750 mm 21.4 liters  

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. This preconfigured tank comes with: Double jacket with 2xG1" external connections Liquid level indicator with a liter scale Welded gland NW10 for sampling Welded gland for thermometer NW10 with cap Venting welded gland with a 2 in. TC connection Racking outlet with a 2 in TC connection Bottom outlet with a 2 in. TC connection Dome with a hinged and swiveling venting gland Mash door - 12.2 in. (310 mm) x 16.5 in. (420 mm) Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time. Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters View the resource for more information on the key features of all Speidel Tanks.

Read more less

The FO2 tank from Speidel is one step up from their BO style tank and is a great option for home winemakers and wineries with small lots of wine to store. Speidel's unique pocketed tank bases are molded into shape so there are no welds on the bottom surface of the tank, and offer complete drainage. All FO2 tanks are equipped with 1.5" TC racking and drain ports. Key Features Available in four sizes: 300L, 530L, 675L and 910L 300L tank has a 17mm wide top flange, all other tanks have a 42mm wide flange Tanks from 530L up have a reinforcing plate at the racking valve to prevent tank wall flex and to support a tank mixer Liter scale on exterior of tank On three legs View the resource for more information on the key features of all Speidel Tanks. Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.

Read more less

The age-old, and still practiced, process of manual punch down is now modernized, automated and brought to a larger scale thanks to Speidel! This simple but effective system features an external  pneumatic cylinder which drives the punching assembly. During the downward stroke the folding stainless punching wings lay flat against the top of the pommace cap and push the solids back into the fermenting wine. On the upward stroke of the cycle the wings set at angle which induces the wings to rotate about 30 degrees, position themselves over a fresh segment of the cap, and the cycle then repeats itself. The whole cap can be punched in as little as 5-6 punch cycles—about 15 minutes! The duration of time that the tank performs punch downs, and the interval of time between them, are adjustable depending on your individual vineyard, vintage and winemaking style. Must Discharge: Forward sloped Fermentation Manway with hinged door opening Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Tank ceiling is reinforced to withstand the punchdown forces. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Compressor should be able to provide 500L/min at 6 bar pressure with a minimum of 90L tank capacity (17.7 CFM at 87 psi with a 24 gallon tank). Speidel recommends that the compressed air be conditioned before entering the pneumatic cylinder and recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent. Air Consumption per punch cycle: Immersion Depth Air Consumption 1000 mm 12.3 liters 1250 mm 15.3 liters 1500 mm 18.3 liters 1750 mm 21.4 liters  

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be customized with a wide array of add-on features, and can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time. Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters View the resource for more information on the key features of all Speidel Tanks.

Read more less

The age-old, and still practiced, process of manual punch down is now modernized, automated and brought to a larger scale thanks to Speidel! This simple but effective system features an external  pneumatic cylinder which drives the punching assembly. During the downward stroke the folding stainless punching wings lay flat against the top of the pommace cap and push the solids back into the fermenting wine. On the upward stroke of the cycle the wings set at angle which induces the wings to rotate about 30 degrees, position themselves over a fresh segment of the cap, and the cycle then repeats itself. The whole cap can be punched in as little as 5-6 punch cycles—about 15 minutes! The duration of time that the tank performs punch downs, and the interval of time between them, are adjustable depending on your individual vineyard, vintage and winemaking style. Must Discharge: Forward sloped Fermentation Manway with gate-style opening allows of fine netering  of how fast you allow must to flow out of the tank. Especially useful with thin musts. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Tank ceiling is reinforced to withstand the punchdown forces. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Compressor should be able to provide 500L/min at 6 bar pressure with a minimum of 90L tank capacity (17.7 CFM at 87 psi with a 24 gallon tank). Speidel recommends that the compressed air be conditioned before entering the pneumatic cylinder and recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent. Air Consumption per punch cycle: Immersion Depth Air Consumption 1000 mm 12.3 liters 1250 mm 15.3 liters 1500 mm 18.3 liters 1750 mm 21.4 liters  

Read more less

Speidel's SD-MGRL Tanks bring high tech fermentation solutions to wineries with restricted ceiling heights. The horizontal red wine fermenter is equipped with a slow-moving center shaft with mixing arms attached to it, which effectively break up and re-submerge the cap after just a few rotations. The duration of and interval between immersion operations is programmable to suit the needs of your different vineyards and vintages as well as your individual winemaking style. The mixing arms are slanted forward which pushes must forward and promotes complete emptying of the tank once fermentation is complete through the 125,mm (5") drain valve.   Key Features: Tank entirely in AISI304 stainless steel. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow 42x32 cm (16.5x12.5 in) Oval Racking Door Included NW 10 DIN stainless thermowell with analog bi-metal thermometer insert Included NW 20 DIN stainless sample valve 125 mm (5") threaded drain port, 2” Tri-Clamp racking outlet. Stainless steel electronic control box 380V 3-phase gear-reduced mixing motor turns at 3 rpm for cap management and at 6 rpm for must evacuation.

Read more less

The age-old, and still practiced, process of manual punch down is now modernized, automated and brought to a larger scale thanks to Speidel! This simple but effective system features an external  pneumatic cylinder which drives the punching assembly. During the downward stroke the folding stainless punching wings lay flat against the top of the pommace cap and push the solids back into the fermenting wine. On the upward stroke of the cycle the wings set at angle which induces the wings to rotate about 30 degrees, position themselves over a fresh segment of the cap, and the cycle then repeats itself. The whole cap can be punched in as little as 5-6 punch cycles—about 15 minutes! The duration of time that the tank performs punch downs, and the interval of time between them, are adjustable depending on your individual vineyard, vintage and winemaking style. Must Discharge: Automatic, motorized must-discharge arms with hinged door opening. Must-Discharge motor requires 380V, 3-phase power. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Tank ceiling is reinforced to withstand the punchdown forces. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Compressor should be able to provide 500L/min at 6 bar pressure with a minimum of 90L tank capacity (17.7 CFM at 87 psi with a 24 gallon tank). Speidel recommends that the compressed air be conditioned before entering the pneumatic cylinder and recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent. Air Consumption per punch cycle: Immersion Depth Air Consumption 1000 mm 12.3 liters 1250 mm 15.3 liters 1500 mm 18.3 liters 1750 mm 21.4 liters  

Read more less

The FO Variable Volume tank is Speidel's flagship Variable Volume tank for storage. Available in 28 different capacities from 1,100L up to over 15,000L. Each tank has multiple cooling jacket styles and a host of other optional add-ons available. Truly customizable to your winery's needs! Key Features Available in 28 sizes covering 6 different tank diameters from 1,100L to 15,200L (larger tanks available with special shipping arrangements) 1,100L & 1,650L Tanks equipped with 1.5" TC racking and drainage ports. All other tanks equipped with 2" TC. Larger fittings available by request Reinforced racking ports prevent tank wall flex and can support the weight of a tank mixer. All tanks have welded-on mounting points for lid lifting arms. Tanks from 1,650L include a lifting arm; from 2,200L up the arm is winch-operated View the resource for more information on the key features of all Speidel Tanks. Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.

Read more less

The age-old, and still practiced, process of manual punch down is now modernized, automated and brought to a larger scale thanks to Speidel! This simple but effective system features an external  pneumatic cylinder which drives the punching assembly. During the downward stroke the folding stainless punching wings lay flat against the top of the pommace cap and push the solids back into the fermenting wine. On the upward stroke of the cycle the wings set at angle which induces the wings to rotate about 30 degrees, position themselves over a fresh segment of the cap, and the cycle then repeats itself. The whole cap can be punched in as little as 5-6 punch cycles—about 15 minutes! The duration of time that the tank performs punch downs, and the interval of time between them, are adjustable depending on your individual vineyard, vintage and winemaking style. Must Discharge: Forward sloped Fermentation Manway with gate-style opening allows of fine netering  of how fast you allow must to flow out of the tank. Especially useful with thin musts. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Tank ceiling is reinforced to withstand the punchdown forces. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Compressor should be able to provide 500L/min at 6 bar pressure with a minimum of 90L tank capacity (17.7 CFM at 87 psi with a 24 gallon tank). Speidel recommends that the compressed air be conditioned before entering the pneumatic cylinder and recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent. Air Consumption per punch cycle: Immersion Depth Air Consumption 1000 mm 12.3 liters 1250 mm 15.3 liters 1500 mm 18.3 liters 1750 mm 21.4 liters  

Read more less

The FO Variable Volume tank is Speidel's flagship Variable Volume tank for storage. Available in 28 different capacities from 1,100L up to over 15,000L. Each tank has multiple cooling jacket styles and a host of other optional add-ons available. Truly customizable to your winery's needs! Key Features Available in 28 sizes covering 6 different tank diameters from 1,100L to 15,200L (larger tanks available with special shipping arrangements) 1,100L & 1,650L Tanks equipped with 1.5" TC racking and drainage ports. All other tanks equipped with 2" TC. Larger fittings available by request Reinforced racking ports prevent tank wall flex and can support the weight of a tank mixer. All tanks have welded-on mounting points for lid lifting arms. Tanks from 1,650L include a lifting arm; from 2,200L up the arm is winch-operated View the resource for more information on the key features of all Speidel Tanks. Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.

Read more less

The FO Variable Volume tank is Speidel's flagship Variable Volume tank for storage. Available in 28 different capacities from 1,100L up to over 15,000L. Each tank has multiple cooling jacket styles and a host of other optional add-ons available. Truly customizable to your winery's needs! Key Features Available in 28 sizes covering 6 different tank diameters from 1,100L to 15,200L (larger tanks available with special shipping arrangements) 1,100L & 1,650L Tanks equipped with 1.5" TC racking and drainage ports. All other tanks equipped with 2" TC. Larger fittings available by request Reinforced racking ports prevent tank wall flex and can support the weight of a tank mixer. All tanks have welded-on mounting points for lid lifting arms. Tanks from 1,650L include a lifting arm; from 2,200L up the arm is winch-operated View the resource for more information on the key features of all Speidel Tanks. Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.

Read more less

The age-old, and still practiced, process of manual punch down is now modernized, automated and brought to a larger scale thanks to Speidel! This simple but effective system features an external  pneumatic cylinder which drives the punching assembly. During the downward stroke the folding stainless punching wings lay flat against the top of the pommace cap and push the solids back into the fermenting wine. On the upward stroke of the cycle the wings set at angle which induces the wings to rotate about 30 degrees, position themselves over a fresh segment of the cap, and the cycle then repeats itself. The whole cap can be punched in as little as 5-6 punch cycles—about 15 minutes! The duration of time that the tank performs punch downs, and the interval of time between them, are adjustable depending on your individual vineyard, vintage and winemaking style. Must Discharge: Automatic, motorized must-discharge arms with gate-style opening allows for fine netering of how fast you allow must to flow out of the tank. Especially useful with thin musts. Must-Discharge motor requires 380V, 3-phase power. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Tank ceiling is reinforced to withstand the punchdown forces. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Compressor should be able to provide 500L/min at 6 bar pressure with a minimum of 90L tank capacity (17.7 CFM at 87 psi with a 24 gallon tank). Speidel recommends that the compressed air be conditioned before entering the pneumatic cylinder and recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent. Air Consumption per punch cycle: Immersion Depth Air Consumption 1000 mm 12.3 liters 1250 mm 15.3 liters 1500 mm 18.3 liters 1750 mm 21.4 liters  

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be customized with a wide array of add-on features, and can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time. Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters View the resource for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be customized with a wide array of add-on features, and can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time. Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters View the resource for more information on the key features of all Speidel Tanks.

Read more less

The age-old, and still practiced, process of manual punch down is now modernized, automated and brought to a larger scale thanks to Speidel! This simple but effective system features an external  pneumatic cylinder which drives the punching assembly. During the downward stroke the folding stainless punching wings lay flat against the top of the pommace cap and push the solids back into the fermenting wine. On the upward stroke of the cycle the wings set at angle which induces the wings to rotate about 30 degrees, position themselves over a fresh segment of the cap, and the cycle then repeats itself. The whole cap can be punched in as little as 5-6 punch cycles—about 15 minutes! The duration of time that the tank performs punch downs, and the interval of time between them, are adjustable depending on your individual vineyard, vintage and winemaking style. Must Discharge: Automatic, motorized must-discharge arms with gate-style opening allows for fine netering of how fast you allow must to flow out of the tank. Especially useful with thin musts. Must-Discharge motor requires 380V, 3-phase power. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Tank ceiling is reinforced to withstand the punchdown forces. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Compressor should be able to provide 500L/min at 6 bar pressure with a minimum of 90L tank capacity (17.7 CFM at 87 psi with a 24 gallon tank). Speidel recommends that the compressed air be conditioned before entering the pneumatic cylinder and recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent. Air Consumption per punch cycle: Immersion Depth Air Consumption 1000 mm 12.3 liters 1250 mm 15.3 liters 1500 mm 18.3 liters 1750 mm 21.4 liters  

Read more less

The FO Variable Volume tank is Speidel's flagship Variable Volume tank for storage. Available in 28 different capacities from 1,100L up to over 15,000L. Each tank has multiple cooling jacket styles and a host of other optional add-ons available. Truly customizable to your winery's needs! Key Features Available in 28 sizes covering 6 different tank diameters from 1,100L to 15,200L (larger tanks available with special shipping arrangements) 1,100L & 1,650L Tanks equipped with 1.5" TC racking and drainage ports. All other tanks equipped with 2" TC. Larger fittings available by request Reinforced racking ports prevent tank wall flex and can support the weight of a tank mixer. All tanks have welded-on mounting points for lid lifting arms. Tanks from 1,650L include a lifting arm; from 2,200L up the arm is winch-operated View the resource for more information on the key features of all Speidel Tanks. Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.

Read more less

The FO-M tank from Speidel is very similar to the the standard FO style variable volume storage tank. The FO-M tank, however, has been specially altered to make it more useful as a fermentation tank, and comes pre-fitted with the most standard features equipped on tanks used for red fermentations. And they have the same degree of flexibility and customization available as the standard FO style tank, but offer an easy starting point and cost savings for tanks destined for red fermentation. And don't miss out on Spediel's Mobile Must Plunger, which makes punch downs fast, easy and automatic! Key Features Available in 28 sizes covering 6 different tank diameters from 1,100L to 15,200L Tank is equipped with rectangular manway for must discharge. Legs elevated to 52cm height for easier must discharge. Can be extended up to 80cm to accommodate a macro bin under the manway. Bottom drain is rotated to just in front of the left tank leg so it's out of the way of must receptacle. 1,100L & 1,600L Tanks equipped with 1.5" TC racking and drainage ports. All other tanks equipped with 2" TC. Larger fittings available by request Reinforced racking ports prevent tank wall flex and can support the weight of a tank mixer. All tanks include a lifting arm. Mobile, forkliftable Pneumatic Must Plunger available to go with these tanks! View the resource for more information on the key features of all Speidel Tanks. Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.

Read more less

The FO Variable Volume tank is Speidel's flagship Variable Volume tank for storage. Available in 28 different capacities from 1,100L up to over 15,000L. Each tank has multiple cooling jacket styles and a host of other optional add-ons available. Truly customizable to your winery's needs! Key Features Available in 28 sizes covering 6 different tank diameters from 1,100L to 15,200L (larger tanks available with special shipping arrangements) 1,100L & 1,650L Tanks equipped with 1.5" TC racking and drainage ports. All other tanks equipped with 2" TC. Larger fittings available by request Reinforced racking ports prevent tank wall flex and can support the weight of a tank mixer. All tanks have welded-on mounting points for lid lifting arms. Tanks from 1,650L include a lifting arm; from 2,200L up the arm is winch-operated View the resource for more information on the key features of all Speidel Tanks. Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be customized with a wide array of add-on features, and can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time. Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters View the resource for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be customized with a wide array of add-on features, and can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time. Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters View the resource for more information on the key features of all Speidel Tanks.

Read more less

The FO Variable Volume tank is Speidel's flagship Variable Volume tank for storage. Available in 28 different capacities from 1,100L up to over 15,000L. Each tank has multiple cooling jacket styles and a host of other optional add-ons available. Truly customizable to your winery's needs! Key Features Available in 28 sizes covering 6 different tank diameters from 1,100L to 15,200L (larger tanks available with special shipping arrangements) 1,100L & 1,650L Tanks equipped with 1.5" TC racking and drainage ports. All other tanks equipped with 2" TC. Larger fittings available by request Reinforced racking ports prevent tank wall flex and can support the weight of a tank mixer. All tanks have welded-on mounting points for lid lifting arms. Tanks from 1,650L include a lifting arm; from 2,200L up the arm is winch-operated View the resource for more information on the key features of all Speidel Tanks. Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.

Read more less

The age-old, and still practiced, process of manual punch down is now modernized, automated and brought to a larger scale thanks to Speidel! This simple but effective system features an external  pneumatic cylinder which drives the punching assembly. During the downward stroke the folding stainless punching wings lay flat against the top of the pommace cap and push the solids back into the fermenting wine. On the upward stroke of the cycle the wings set at angle which induces the wings to rotate about 30 degrees, position themselves over a fresh segment of the cap, and the cycle then repeats itself. The whole cap can be punched in as little as 5-6 punch cycles—about 15 minutes! The duration of time that the tank performs punch downs, and the interval of time between them, are adjustable depending on your individual vineyard, vintage and winemaking style. Must Discharge: Automatic, motorized must-discharge arms with hinged door opening. Must-Discharge motor requires 380V, 3-phase power. Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Tank ceiling is reinforced to withstand the punchdown forces. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow NW 10 DIN stainless thermowell with thermometer insert NW 20 DIN stainless sample valve Standard 2” Tri-Clamp racking and total drain outlets. Stainless steel electronic control box System Electrical and Pneumatic Requirements: 220V, 1-phase, 60Hz power for the control system. Compressor should be able to provide 500L/min at 6 bar pressure with a minimum of 90L tank capacity (17.7 CFM at 87 psi with a 24 gallon tank). Speidel recommends that the compressed air be conditioned before entering the pneumatic cylinder and recommends either the FESTO FRC-1/2-D MIDI-A (Part No. 159591) or the SMC AC40A-F04DE or equivalent. Air Consumption per punch cycle: Immersion Depth Air Consumption 1000 mm 12.3 liters 1250 mm 15.3 liters 1500 mm 18.3 liters 1750 mm 21.4 liters  

Read more less

The FO Variable Volume tank is Speidel's flagship Variable Volume tank for storage. Available in 28 different capacities from 1,100L up to over 15,000L. Each tank has multiple cooling jacket styles and a host of other optional add-ons available. Truly customizable to your winery's needs! Key Features Available in 28 sizes covering 6 different tank diameters from 1,100L to 15,200L (larger tanks available with special shipping arrangements) 1,100L & 1,650L Tanks equipped with 1.5" TC racking and drainage ports. All other tanks equipped with 2" TC. Larger fittings available by request Reinforced racking ports prevent tank wall flex and can support the weight of a tank mixer. All tanks have welded-on mounting points for lid lifting arms. Tanks from 1,650L include a lifting arm; from 2,200L up the arm is winch-operated View the resource for more information on the key features of all Speidel Tanks. Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.

Read more less

The FO Variable Volume tank is Speidel's flagship Variable Volume tank for storage. Available in 28 different capacities from 1,100L up to over 15,000L. Each tank has multiple cooling jacket styles and a host of other optional add-ons available. Truly customizable to your winery's needs! Key Features Available in 28 sizes covering 6 different tank diameters from 1,100L to 15,200L (larger tanks available with special shipping arrangements) 1,100L & 1,650L Tanks equipped with 1.5" TC racking and drainage ports. All other tanks equipped with 2" TC. Larger fittings available by request Reinforced racking ports prevent tank wall flex and can support the weight of a tank mixer. All tanks have welded-on mounting points for lid lifting arms. Tanks from 1,650L include a lifting arm; from 2,200L up the arm is winch-operated View the resource for more information on the key features of all Speidel Tanks. Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be customized with a wide array of add-on features, and can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time. Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters View the resource for more information on the key features of all Speidel Tanks.

Read more less

These Speidel Sealed Transport tanks are the perfect solution for winemakers who have, well, wine to transport! The modular, stackable design makes them easy to store and useful around the winery when not being used for transport. The 1000L capacity means they can be picked up with a standard forklift when full, and the fact that they fit the footprint of a standard pallet means they will fit in the bed of most full-sized pickup trucks. Key Features Sealed top with welded on D-Tabs for lifting the tank 40cm hinged top hatch with 2''TC vent neck with sealing cap. Molded, fully draining tank bottom with 2''TC. Stainless steel frame, accessible from four sides by forklift. Maximum stack of 3 tanks when full View the resource for more information on the key features of all Speidel Tanks.

Read more less

The FO Variable Volume tank is Speidel's flagship Variable Volume tank for storage. Available in 28 different capacities from 1,100L up to over 15,000L. Each tank has multiple cooling jacket styles and a host of other optional add-ons available. Truly customizable to your winery's needs! Key Features Available in 28 sizes covering 6 different tank diameters from 1,100L to 15,200L (larger tanks available with special shipping arrangements) 1,100L & 1,650L Tanks equipped with 1.5" TC racking and drainage ports. All other tanks equipped with 2" TC. Larger fittings available by request Reinforced racking ports prevent tank wall flex and can support the weight of a tank mixer. All tanks have welded-on mounting points for lid lifting arms. Tanks from 1,650L include a lifting arm; from 2,200L up the arm is winch-operated View the resource for more information on the key features of all Speidel Tanks. Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be customized with a wide array of add-on features, and can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time. Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters View the resource for more information on the key features of all Speidel Tanks.

Read more less

The FO-M tank from Speidel is very similar to the the standard FO style variable volume storage tank. The FO-M tank, however, has been specially altered to make it more useful as a fermentation tank, and comes pre-fitted with the most standard features equipped on tanks used for red fermentations. And they have the same degree of flexibility and customization available as the standard FO style tank, but offer an easy starting point and cost savings for tanks destined for red fermentation. And don't miss out on Spediel's Mobile Must Plunger, which makes punch downs fast, easy and automatic! Key Features Available in 28 sizes covering 6 different tank diameters from 1,100L to 15,200L Tank is equipped with rectangular manway for must discharge. Legs elevated to 52cm height for easier must discharge. Can be extended up to 80cm to accommodate a macro bin under the manway. Bottom drain is rotated to just in front of the left tank leg so it's out of the way of must receptacle. 1,100L & 1,600L Tanks equipped with 1.5" TC racking and drainage ports. All other tanks equipped with 2" TC. Larger fittings available by request Reinforced racking ports prevent tank wall flex and can support the weight of a tank mixer. All tanks include a lifting arm. Mobile, forkliftable Pneumatic Must Plunger available to go with these tanks! View the resource for more information on the key features of all Speidel Tanks. Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.

Read more less

Please​ note: the primary image is an example image and does not exactly match this tank. See below for features and specifications. Variable capacity tank well-suited for fermentation, wine aging, kombucha, and other applications Floating lid can be positioned as needed to match the volume of the liquid you're working with Proprietary rubber lid gasket allows for a superior seal compared to traditional gaskets, providing better protection for your wine Double jacket for glycol cooling Pulley rope for lowering and lifting the floating lid Made in Germany by Speidel We are proud to present our line of premium quality stainless steel tanks. Built in Germany by Speidel, the world-class traditions of German engineering and craftsmanship are reflected in these tanks. And, after examining tanks built by every major manufacturer worldwide, we can safely say that when it comes to features, quality and price, these tanks represent the very best value available in stainless steel wine storage. Speidel Quality Features: Cooling Jacket - Fermenters are equipped with a double jacket that is designed for an operating pressure of 2.5 to 6 bar. This will allow you to hook it into a glycol system (see our Kreyer Chilly45, GLY410) for complete temperature control! Interior Finish - Speidel tanks feature an ultra-smooth 2R rated interior surface which effectively resists the build-up of tartrate residues. Clean your tanks with cold water after cold stabilization! Say goodbye to harsh cleaning chemicals and expensive CIP systems! Weld Quality - Speidel's robotic-arm laser welders create flawless stainless to stainless junctions that look and feel more like a taped fabric seam than a traditional weld. Ultra high-quality welds leave no chance for residual product to harbor spoilage organisms. Thickness - Speidel tanks are designed to be the correct thickness for the tank's total volume. Complete Drainage Bottoms - All Speidel tanks are outfitted with conical, pocketed bottoms for total drainage, which maximizes product yield at rackings and makes cleaning a snap. *Please note that smaller, flat-bottomed tanks do not feature total drainage bottoms. Tri-Clamp Valve Ferrules - All Speidel tanks come configured for use with Tri-Clamp (TC) style valves and fittings. Tanks up to 1600L capacity are outfitted with 1.5" TC racking outlet and bottom outlet. **Please Note: TC valves not included. Please inquire with your sales associate for pricing on TC valves and fittings. Rubber Lid Gaskets - The white rubber gaskets used by Speidel are much thicker than the traditional clear vinyl gaskets, which along with their extruded manufacturing process provide a much better seal with the tanks wall. They're seamless and more oxygen resistant than the clear gaskets. That means better protection for your wines! Warranty - Speidel-Behaelter, GMBH backs up each and every tank with an industry-leading 25 year warranty against defects in materials or workmanship. And, as a 5th generation manufacturer, you can be confident they'll be around to honor that warranty should the need arise. Tank Features: Volume: Sealed, 1100 L Variable Capacity Tank includes Floating lid and Heavy Duty White Rubber Gasket Complete Drainage Dish Bottom Lifting Arm Reinforced Racking valve 1.5" TC connections NW10 fitting for use with Sample Valve or Thermometer and Thermowell Combo (Sample Valve or Thermometer and Thermowell not included)   Note: Over tightening the airlock / orange bulk head can cause it to crack. Only thread the airlock down until it feels snug. Do not over tighten.  

Read more less

Speidel's FS-MO and AS-MO tanks are their flagship storage and fermentation tanks. Featuring a huge range of tank capacities, these tanks can be customized with a wide array of add-on features, and can be stacked to take advantage of vertical space in your facility. The FS-MO tank is the tank used for the base, and up to two AS-MO tanks stack on. Please note that with each diameter range there is a maximum total volume for all tanks in a stack shown below, due to the weight of the tanks when full. Key Features Tank walls and base in AISI304 stainless, tank top is AISI316 stainless for additional SO2 gas resistance Base tanks from 200cm and up in height, and all stacking tanks, include a ladder support bow TC Ferrule on tank top for affixing a valve, bung or blowoff tube. TC racking port is strong enough to support a tank mixer. TC pocketed tank base drains completely 1.5" TC Fittings on tanks up through 1,600L. 2" Fittings on tanks 1,601L and up. Larger fittings available by request All tanks outfitted with DN10 threaded port to accommodate a sample valve (Valve part number H587) All tanks feature a weld-free, molded oval racking door/manway All tanks are pre-equipped with a DN10 threaded port and mounting points to affix a sight gauge at any time. Tank Diameter Maximum Total Volume of Tank Stack 82 cm 1265 Liters 100 cm 2500 Liters 120 cm 4600 Liters 140 cm 6700 Liters 160 cm 10000 Liters 180 cm 12500 Liters 200 cm 16300 Liters View the resource for more information on the key features of all Speidel Tanks.

Read more less

Speidel's FD-MBT Tanks are designed for intermediate storage of incoming grapes or fermented must until they can be processed or pressed off . These high capacity tanks feature integrated mixing bars to keep your fruit/must homogenous during storage, and motorized wiper bars on the tank bottom to ensure that the tank is fully emptied via the 125 mm (5") outlet port..   Key Features: Tank ceiling in AISI316 Stainless, tank walls and base in AISI304. Forward set, vertical 40 cm (16”) top hatch with 2” Tri-Clamp ferrule Ladder support bow 42x32 cm (16.5x12.5 in) Oval Racking Door 125 mm (5") threaded drain port, 2” Tri-Clamp racking outlets. Stainless steel electronic control box 3 Kw (4 HP), 380V 3-phase gear-reduced mixing motor turns at 8 rpm.

Read more less