Dozens of fittings and valves for almost any winemaking application.
Fittings & Valves
Shop By Collection
-
3 Piece Stainless Ball Valve - 1.5 in. T.C.
Stainless steel 3-piece ball valve with tri-clamp connections. A great option for T.C. kettles, pumps, and conicals to go from 1.5" tri-clamp to any 1.5" tri-clamp connection or accessory. Full port for higher flow rate.
$32.99
-
Stainless - 1/2 in. FPT Tee
304 Stainless, 1/2" Female Pipe Thread on all three openings. 2" length x 1.5" width
$6.09
-
BrewBuilt® CIP Spray Ball | 1.5" T.C.
BrewBuilt CIP Spray Ball for use with X-Series Uni Conicals or any stainless steel fermenter with 1.5" tri-clamp fittings. The head emits a 360° fan spray that cleans above and below the spinning ball. The sharp spray easily removes soil inside your tank. The long neck design allows the spray ball to reach through tall fittings and ferrules. With a welded 90° elbow inlet, you won't have any trouble with kinked hosing slowing your pump flow and lowering the spray ball's performance. A pump capable of 30-45 psi and 11 GPM is recommended for this product to provide a high pressure cleaning radius of 3.6 ft. When used with BrewBuilt conicals, 7 GPM is enough to coat the full interior of the fermenter, but longer CIP runs might be required to fully breakdown stubborn solid deposits.
$99.99
-
Stainless Street Elbow - 1/2'' fpt x 1/2'' mpt
1/2" Female thread on one side and 1/2" male thread on the other. Called a street elbow because of the female threads on one side and the male threads on the other. Made from 304 type Stainless Steel.
$6.09
-
Gasket for 1.5 in Butterfly Valve
Replacement interior gasket for H661 Butterfly Valve.
$12.49
-
Tri-Clamp 90 Elbow (2")
304-type polished stainless. A set of "elbows" is great for connecting hoses to a pump so they run parallel to each other. With 2" and 3" hose, this dramatically reduces the space needed to allow the pump to pass. In addition, having the lines run parallel makes the pump more agile when moving around the winery when connected.
$25.49
-
ForgeFit® Stainless Tri-Clamp Hose End | 3" Barb x 3" T.C.
This ForgeFit oversized barb hose end is intended for use with professional beverage tubing. 3" tri-clamp connection with 3" OD barb.
$58.49
-
Brass Hose Connector | Female Hose Thread x 1/2 in Barb
Useful piece for connecting tubing to a Wort Chiller. Female Garden Hose on one side, with a 1/2" OD barb for tubing on the other side.
$5.49
-
Brass Hose - Female Hose x 3/8'' Barb
Useful piece for connecting tubing to a Wort Chiller. Female Garden Hose on one side, with a 3/8" OD barb for tubing on the other side.
$4.99
-
ForgeFit® Stainless Tri-Clamp Tee | 1.5"
304-type stainless steel tri-clamp tee with 1.5" clamp ends.
$25.99
-
Stainless Tri-Clamp Weldless Bulkhead - 2 in.
Add a 2" tri-clamp port to any tank or lid with this 304 stainless steel weldless bulkhead. Just drill a 45-47 mm hole and tighten this item to your vessel wall. For distilling purposes, this is perfect if you want to fit an extension tube between the BrewZilla / DigiBoil distillation lid and the copper pot or reflux still. Kegland Part Number: KL10979
$32.99
-
ForgeFit® Tri-Clamp Gasket | Silicone | 2.5"
Silicone gasket for 2.5" tri-clamp connection. Temperature rated from -58°F to 446°F.
$3.49
-
Tri-Clamp Thermowell
1.5" Tri-Clamp end cap welded to thin wall stainless tubing for quick accurate temperature readings. Insert 1/4" thermal probe from controller. Works perfectly with our Ranco digital controllers. Thermowell mounts into 1.5" Tri-Clamp ferrule in the side or your tank. Has a 6 inch probe. Works with new 2016 Rancos
$32.99
-
ForgeFit® Stainless Butterfly Valve | 1.5" T.C.
This 1.5" Tri-Clamp Butterfly Valve features stainless steel construction and 7-position handle. The stainless steel handle can be rotated 180° for right or left hand operation.
$74.49
-
Stainless Coupler - 3/4" FPT x 1/2" FPT
A stainless steel coupler with 3/4" FPT x 1/2" FPT threads. Great for March Pumps with a 3/4" Center Inlet!
$5.49
-
Stainless Tri-Clamp Ferrule | 1.5" T.C.
Stainless - 1.5" TC Ferrule. Used to weld in a TC connection anywhere you need one! Total Length: 1 3/32" Inner Diameter: 1 13/32". AiSI304 Stainless Steel.
$9.89
-
Stainless - 1/4 in 3 Way Ball Valve - FPT x MPT x FPT
Stainless - 1/4 in 3 Way Ball Valve - FPT x MPT x FPT Please Note: Valves include a Teflon gasket. Do not soak the valves in PBW which can corrode Teflon material after prolonged contact.
$28.99
-
Stainless - Nipple - 1/2 in. x 1.5 in.
A stainless steel nipple used to combine two fittings with 1/2" FPT threads. There is a 1/2'' space between threads.
$3.29
-
Stainless 1/2 in MPT Plug - Hollow
Stainless 1/2 in MPT Plug. Hollow behind threads
$6.59
-
ForgeFit® 1.5 in. Butterfly Valve Gasket
Replacement gasket for the ForgeFit® 1.5" butterfly valve. We recommend replacing your butterfly gasket at least every 3 years. If you wait until you have a leak, your valve has already been unsanitary for some time.
$18.49
-
Stainless Nipple - 1/2" x 2" Threaded
Stainless Nipple - 1/2" x 2" Threaded There is approximately a 1/2" of thread on both side of this fitting and a one inch section that is unthreaded.
$4.39
-
Stainless Nipple - 3/4" x Close
Stainless Nipple - 3/4" x Close
$5.49
-
$8.79
-
Tri-Clamp Gasket with Stainless Mesh Screen | 7 Mesh | Teflon | 2"
Teflon gasket with 304 stainless mesh screen for 2" tri-clamp connections. Can be used as a filter screen to trap large particulates passing through T.C. fittings. Often used for distillation to retain activated carbon for filtering neutral spirits or used in pot distillation to retain botanicals in the vapor stream. The screen has a mesh size of 7 which will block particles larger than 2.83mm or 2830 microns. This slightly larger mesh size makes this screen ideal for use in a distillation basket. KegLand Part Number: KL11921
$7.19
-
Tri-Clamp Spunding Valve | Integrated Pressure Gauge | Scaled Spunding Valve | Polycarbonate Liquid Cylinder | 2.2 BAR | 0-32 PSI | 1.5" T.C. | Stainless Steel
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive more in late July. For commercial brewery application with a range of 0-2.2 Bar. For homebrew fermenters, see the BrewBuilt® Spunding Valve Automatically release pressure inside your fermenter during pressure fermentations Compatible with any stainless steel pressurizable fermenter with 1.5" tri-clamp ports In-line pressure gauge for easy reference of tank pressure reads from 0-35 PSI Made from 304 stainless steel and comes fully assembled This tri-clamp spunding valve provides professional-level accuracy for fermenting under pressure. Attach to any pressurizable stainless steel conical with 1.5" TC ports and set your desired blow-off pressure. A pressure gauge sits in-line from the conical to the spunding valve so you can reference the current pressure inside your vessel at any time. The polycarbonate cylinder that surrounds the spunding valve can be filled with water or sanitizer to keep your tank 100% sanitary throughout the fermentation process. Not designed for homebrewing conicals where the maximum allowed pressure does not exceed 1 Bar. The pressure gauge reads from 0-35 psi or 0-0.25 MPa. The spunding valve is scaled in both psi and BAR, up to 32 psi (2.2 BAR). Comes fully assembled 1.5" tri-clamp connection In-line pressure gauge Made from 304 stainless steel For Your Safety: Never exceed the maximum rated working pressure of your vessel at any time during operation. The fixed-pressure PRV on your conical should always remain in place while using this spunding valve.
$299.99
-
Stainless - 1 in. Full Coupler BSPP
Full Coupler with 1" Female British Standard Pipe Parallel Thread. Full couplers have threads for insertion from both sides.
$7.69
-
Stainless Ball Valve - 1" Full Port
Our Ball Valves will last for years. Easy to clean. High grade 304-stainless made to last. 1" FPT on input and output side. TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and two gaskets that form the seal when closed. Please Note: the ball valve may be difficult to turn at first, but it will become less resistant after it is rotated back and forth a couple times.
$29.99
-
Stainless - Elbow - 1/2 in. FPT x 1/2 in. FPT
Stainless steel elbow with a 1/2" FPT inlet and 1/2" FPT outlet. Max pressure rating of 150 psi.
$6.09
-
Stainless Barb - 1/2 in. x 1/2 in. Male BSP
Stainless steel barb fitting. 1/2" male BSP x 13mm barb (0.51"). KegLand Part Number: KL03629
$6.59
-
Plastic Barb - 1/4 in. x 1/2 in. MPT
Plastic 1/4" barb with 1/2" male thread. This is the same barb we use on our Beer and Wine Filter Kit (FIL40).
$1.99
-
ForgeFit® Stainless Butterfly Valve | 2" T.C.
This 2" Tri-Clamp Butterfly Valve features stainless steel construction and 7-position handle. The handle can be rotated 180° for right or left hand operation.
$99.99
-
ForgeFit® Stainless Tri-Clamp | 2.5" Clamp
The most popular choice for sanitary connections, tri-clamp fittings are widely used in the food & beverage industry due to their ability to be cleaned in place. Tri-clamps join two fittings together without any nooks or crannies for contaminants to hide. Use anywhere you want to ensure a sanitary connection. 2.5" tri-clamp Made from 304 stainless steel
$11.49
-
Stainless - 1" MPT x 1/2" FPT Bushing
This bushing is to use when you want to use your larger pumps with an other fitting.
$6.09
-
ForgeFit® Stainless Tri-Clamp End Cap | 3"
End cap for 3" tri-clamp fittings. Made from 304 stainless steel.
$8.49
-
ForgeFit® CIP Spray Ball - 1.5 in. T.C.
1.5" tri-clamp "clean in place" spray ball. A pump capable of 29 PSI minimum is recommended for this product.
$41.49
-
ForgeFit® Tri-Clamp Gasket | Silicone | 4"
Silicone gasket for 4" tri-clamp connection. Temperature rated from -58°F to 446°F.
$4.49
-
ForgeFit® Stainless Tri-Clamp Concentric Reducer | 3" x 2"
3" x 2" tri-clamp concentric reducer. Made from 304 stainless steel.
$48.49
-
Stainless Tri-Clamp - 4 in. End Cap w/ Pre Drilled Hole
Use this 4" T.C. end cap to attach an airlock to your kegmenter unit. The hole measures 13/16", which is perfect for a #3 stopper (FE410VS). Kegland Part Number: KL06163
$14.49
-
Tri-Clamp Gasket with Stainless Mesh Screen | 7 Mesh | Teflon | 1.5"
Teflon gasket with 304 stainless mesh screen for 1.5" tri-clamp connections. Can be used as a filter screen to trap large particulates passing through T.C. fittings. Often used for distillation to retain activated carbon for filtering neutral spirits or used in pot distillation to retain botanicals in the vapor stream. This screen can also be used with the 1.5" Hop Bong as an inline filter. The screen has a mesh size of 7 which will block particles larger than 2.83mm or 2830 microns. This slightly larger mesh size makes this screen ideal for use in a distillation basket. KegLand Part Number: KL28516
$7.19
-
Stainless - Full Coupler (1 in.)
Full Coupler with 1" Female Pipe Thread. Full couplers have threads for insertion from both sides.
$5.49
-
Stainless Hex Nipple - 1/2 in. BSP
An excellent upgrade to a standard nipple, these have a hex nut in the center to allow easy tightening and loosening in whatever application it's used! 1/2" male BSP threads. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL06453
$3.89
-
Stainless Tri-Clamp Ferrule | 2" T.C.
2" TC Ferrule for welding onto a tank or section of pipe. 304-type stainless steel. ID is approximately 1-7/8th.
$10.99
-
BrewBuilt® 1.5" Tri-Clamp Thermometer | 6" Probe
The BrewBuilt tri-clamp thermometer features a large 3" face for easy reads and 6" probe for deep penetration into your conical fermenter or T.C. kettle. Dial face reads from 0-220°F and -10-100°C. 3" dial face 6" probe 1.5" T.C. Reads in °F and °C
$44.99
-
Stainless Tri-Clamp Extension Tube - 2 in.
Extension tube with 2" tri-clamp fittings on both ends. 10" in length. Made from 304 stainless steel. Kegland Part Number: KL10665
$32.99
-
Stainless Tri-Clamp | 1.5" T.C. x 1/2" BSP Male
1.5" tri-clamp with 1/2" BSP male threads. Made from 304 stainless steel. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL01847
$16.49
-
Brass Hose - Female Garden Hose Thread x 1/2" MPT
Female Garden Hose Thread on one side with 1/2" MPT on the other. Useful for customizing your chilling configuration! A gasket is included inside the female garden hose thread portion.
$4.49
-
DIN to Tri-Clamp Adapter | DIN NW 25 | 1" DIN x 1.5" T.C.
Speidel 1" DIN to 1.5" TC adapter. If you have a mixture of TC and DIN fittings, there is finally an adapter to help you connect everything together. To top it all off it is made with the expert craftmanship of Speidel.
$58.99
-
$4.39
You have seen 96 out of 267 products