Dozens of fittings and valves for almost any winemaking application.
Fittings & Valves
Shop By Collection
-
Stainless Ball Valve - 1" Full Port
Our Ball Valves will last for years. Easy to clean. High grade 304-stainless made to last. 1" FPT on input and output side. TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and two gaskets that form the seal when closed. Please Note: the ball valve may be difficult to turn at first, but it will become less resistant after it is rotated back and forth a couple times.
$29.99
-
Stainless Nipple - 1/2" x 2" Threaded
Stainless Nipple - 1/2" x 2" Threaded There is approximately a 1/2" of thread on both side of this fitting and a one inch section that is unthreaded.
$4.39
-
Stainless - Elbow - 1/2 in. FPT x 1/2 in. FPT
Stainless steel elbow with a 1/2" FPT inlet and 1/2" FPT outlet. Max pressure rating of 150 psi.
$6.09
-
Plastic Barb - 1/4 in. x 1/2 in. MPT
Plastic 1/4" barb with 1/2" male thread. This is the same barb we use on our Beer and Wine Filter Kit (FIL40).
$1.99
-
Tri-Clamp Gasket with Stainless Mesh Screen | 7 Mesh | Teflon | 2"
Teflon gasket with 304 stainless mesh screen for 2" tri-clamp connections. Can be used as a filter screen to trap large particulates passing through T.C. fittings. Often used for distillation to retain activated carbon for filtering neutral spirits or used in pot distillation to retain botanicals in the vapor stream. The screen has a mesh size of 7 which will block particles larger than 2.83mm or 2830 microns. This slightly larger mesh size makes this screen ideal for use in a distillation basket. KegLand Part Number: KL11921
$7.19
-
ForgeFit® Stainless Tri-Clamp | 2.5" Clamp
The most popular choice for sanitary connections, tri-clamp fittings are widely used in the food & beverage industry due to their ability to be cleaned in place. Tri-clamps join two fittings together without any nooks or crannies for contaminants to hide. Use anywhere you want to ensure a sanitary connection. 2.5" tri-clamp Made from 304 stainless steel
$12.49
-
Stainless - 1 in. Full Coupler BSPP
Full Coupler with 1" Female British Standard Pipe Parallel Thread. Full couplers have threads for insertion from both sides.
$7.69
-
Stainless - 1" MPT x 1/2" FPT Bushing
This bushing is to use when you want to use your larger pumps with an other fitting.
$6.09
-
ForgeFit® Stainless Butterfly Valve | 2" T.C.
This 2" Tri-Clamp Butterfly Valve features stainless steel construction and 7-position handle. The handle can be rotated 180° for right or left hand operation.
$89.49
-
Tri-Clamp Spunding Valve | Integrated Pressure Gauge | Scaled Spunding Valve | Polycarbonate Liquid Cylinder | 2.2 BAR | 0-32 PSI | 1.5" T.C. | Stainless Steel
For commercial brewery application with a range of 0-2.2 Bar. For homebrew fermenters, see the BrewBuilt® Spunding Valve Automatically release pressure inside your fermenter during pressure fermentations Compatible with any stainless steel pressurizable fermenter with 1.5" tri-clamp ports In-line pressure gauge for easy reference of tank pressure reads from 0-35 PSI Made from 304 stainless steel and comes fully assembled This tri-clamp spunding valve provides professional-level accuracy for fermenting under pressure. Attach to any pressurizable stainless steel conical with 1.5" TC ports and set your desired blow-off pressure. A pressure gauge sits in-line from the conical to the spunding valve so you can reference the current pressure inside your vessel at any time. The polycarbonate cylinder that surrounds the spunding valve can be filled with water or sanitizer to keep your tank 100% sanitary throughout the fermentation process. Not designed for homebrewing conicals where the maximum allowed pressure does not exceed 1 Bar. The pressure gauge reads from 0-35 psi or 0-0.25 MPa. The spunding valve is scaled in both psi and BAR, up to 32 psi (2.2 BAR). Comes fully assembled 1.5" tri-clamp connection In-line pressure gauge Made from 304 stainless steel For Your Safety: Never exceed the maximum rated working pressure of your vessel at any time during operation. The fixed-pressure PRV on your conical should always remain in place while using this spunding valve.
$299.99
-
ForgeFit® Stainless Tri-Clamp End Cap | 3"
End cap for 3" tri-clamp fittings. Made from 304 stainless steel.
$8.49
-
Stainless Tri-Clamp - 4 in. End Cap w/ Pre Drilled Hole
Use this 4" T.C. end cap to attach an airlock to your kegmenter unit. The hole measures 13/16", which is perfect for a #3 stopper (FE410VS). Kegland Part Number: KL06163
$14.49
-
ForgeFit® CIP Spray Ball - 1.5 in. T.C.
1.5" tri-clamp "clean in place" spray ball. A pump capable of 29 PSI minimum is recommended for this product.
$41.49
-
ForgeFit® Tri-Clamp Gasket | Silicone | 4"
Silicone gasket for 4" tri-clamp connection. Temperature rated from -58°F to 446°F.
$1.99
-
ForgeFit® Stainless Tri-Clamp Concentric Reducer | 3" x 2"
3" x 2" tri-clamp concentric reducer. Made from 304 stainless steel.
$42.99
-
Stainless - Full Coupler (1 in.)
Full Coupler with 1" Female Pipe Thread. Full couplers have threads for insertion from both sides.
$5.49
-
Stainless Tri-Clamp Ferrule | 2" T.C.
2" TC Ferrule for welding onto a tank or section of pipe. 304-type stainless steel. ID is approximately 1-7/8th.
$10.99
-
Stainless Barb - 1/2 in. x 1/2 in. Male BSP
Stainless steel barb fitting. 1/2" male BSP x 13mm barb (0.51"). KegLand Part Number: KL03629
$6.59
-
Brass Hose - Female Garden Hose Thread x 1/2" MPT
Female Garden Hose Thread on one side with 1/2" MPT on the other. Useful for customizing your chilling configuration! A gasket is included inside the female garden hose thread portion.
$4.49
-
Stainless Tri-Clamp | 1.5" T.C. x 1/2" BSP Male
1.5" tri-clamp with 1/2" BSP male threads. Made from 304 stainless steel. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" and 3/4" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. KegLand Part Number: KL01847
$16.49
-
$4.39
-
Stainless - 2" T.C. x 1" MPT
Adapts 2" Tri-Clover fitting to 1" Male Pipe Thread. 304-type stainless steel.
$30.99
-
BrewBuilt® 1.5" Tri-Clamp Thermometer | 6" Probe
The BrewBuilt tri-clamp thermometer features a large 3" face for easy reads and 6" probe for deep penetration into your conical fermenter or T.C. kettle. Dial face reads from 0-220°F and -10-100°C. 3" dial face 6" probe 1.5" T.C. Reads in °F and °C
$43.99
-
Tri-Clamp Gasket with Stainless Mesh Screen | 7 Mesh | Teflon | 1.5"
Teflon gasket with 304 stainless mesh screen for 1.5" tri-clamp connections. Can be used as a filter screen to trap large particulates passing through T.C. fittings. Often used for distillation to retain activated carbon for filtering neutral spirits or used in pot distillation to retain botanicals in the vapor stream. This screen can also be used with the 1.5" Hop Bong as an inline filter. The screen has a mesh size of 7 which will block particles larger than 2.83mm or 2830 microns. This slightly larger mesh size makes this screen ideal for use in a distillation basket. KegLand Part Number: KL28516
$7.19