Stainless Steel Tri-Clamp Fittings & Valves
-
Tri-Clamp Spunding Valve | Integrated Pressure Gauge | Replacement Polycarbonate Cup Reservoir
Replacement Polycarbonate Cup if you happened to damage or lose the reservoir for the 1.5" Tri-Clover Spunding Valve during routine cleaning and replacement of sanitizer solution post-fermentation. KegLand Part Number: KL27472
$16.49
-
Stainless Tri-Clamp Cross - 1.5 in.
This cross fitting features 1.5" T.C. connections at all ends and is made from high-quality stainless steel. 1.5" tri-clamp 5.75" long x 5.75" tall Made from 304 stainless steel
$32.99
-
ForgeFit® Stainless Tri-Clamp Extension Tube (Spool) | 1.5" T.C. | 18" Long
304-type stainless steel tri-clamp extension tube with 1.5" clamp ends. 18" long.
$34.49
-
Stainless - 2 in. T.C. Check Valve (1 PSI)
This is a Stainless Steel one way Check Valve. It has 2" T.C. Fittings on either side, and releases pressure at ~1 p.s.i. Can be used to inhibit a siphon in certain applications, or to vent gas pressure in a tank.
$109.99 $93.49
-
Flanged Tri-Clamp Gasket | Silicone | 2"
Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections Silicone gaskets have a wide temperature range and are recommended for hot side applications For 2" tri-clamp connections A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both Silicone and EPDM. Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 2" tri-clamp fittings Made from Silicone Temperature rated from -58°F to 446°F KegLand Part Number: KL44820
$2.49
-
ForgeFit® Stainless Beer Thread Adapter | 5/8" Female Beer Thread x 1.5" T.C.
Convert standard 5/8" beer thread to 1.5" tri-clamp. Made from 304 stainless steel.
$17.99
-
ForgeFit® Stainless Tri-Clamp Concentric Reducer | 3" x 1.5"
Adapt any 3" tri-clamp port or valve to work with an existing 1.5" tri-clamp fitting. The concentric design limits flow resistance as you step down from 3" T.C to 1.5" T.C. Perfect for pairing with the BrewBuilt X3 Conical's 3" bottom port and attaching 1.5" tri-clamp fittings. 1.5" x 3" tri-clamp 7" tall Made from 304 stainless steel
$43.99 $37.39
-
FermZilla Stainless Tri-Clamp Reducing Elbow | 3" x 1.5"
Due to high demand, this item is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this to you when we receive more inventory. Stainless steel tri-clamp reducing elbow. Specifically manufactured as an alternative for the FermZilla 27L and 55L Tri-Conical bottom dump port. If you would like to bypass the 3" x 2" butterfly valve and collection container on your FermZilla Tri-Conical, you can use this reducing elbow to go directly to a 1.5" tri-clamp valve. KegLand Part Number: KL29469
$43.99
-
Stainless Tri-Clamp | 3 Piece | 3" Clamp
This stainless steel tri-clamp features two hinges and folds into three pieces. Some brewers find this style of clamp easier to work with on large equipment that requires a 3" clamp. Direct replacement part to the clamp included with the FermZilla Tri-Conical fermenter. KegLand Part Number: KL25799
$14.49
-
BrewBuilt® Tri-Clamp Spunding Valve | 1 BAR | 0.3–14.5 PSI
The BrewBuilt T.C. spunding valve will give you the highest level of accuracy when fermenting under pressure. Designed for use with the BrewBuilt X-Series Uni Conical Fermenter, the spunding valve attaches to the lid's 1.5" tri-clamp port where the blow off fitting is normally installed. It can also be used with any pressurizable stainless steel conical with 1.5" T.C. top ports. The polycarbonate cylinder that surrounds the spunding valve can be filled with water or sanitizer to keep your tank 100% sanitary throughout the fermentation process. Adjustable from 0.3–14.5 psi, designed for the X3 Made from 304 stainless steel 11.75" H x 4" Ø For Your Safety: Never exceed the maximum rated working pressure of your vessel at any time during operation. The fixed-pressure PRV on your conical should always remain in place while using this spunding valve.
$199.99
-
BrewBuilt® Whirlpool Return Fitting | 1.5" T.C.
The BrewBuilt Whirlpool Return Fitting allows you to recirculate wort in your boil kettle without sacrificing one of your tri-clamp ports. Install it in any tri-clamp kettle's thermometer port and attach your preferred valve to the side inlet. The front of the fitting can be capped off with a 1.5" T.C. end cap, or you can pair with the BrewBuilt Thermowell Offset to install a thermometer or temperature probe.
$64.99
-
ForgeFit® Stainless Tri-Clamp Hose End | 1.5" Barb x 1.5" T.C.
This ForgeFit oversized barb hose end is intended for use with 1.5" professional beverage tubing. This is the same fitting we use on our pre-fabricated beverage hose assemblies. When designing this fitting, we made sure it has all the features we wanted in a barb intended for professional applications. The hose barb has a shoulder to keep the hose from creeping up towards the fitting end. The long barb promotes solid engagement with the hose and the end has a gentle internal taper to transition the product flow smoothly from the fitting to the tubing. 1.5" tri-clamp connection with 1.52" OD 3.49" long barb. Overall length 4.95". 3A certified 304 stainless.
$24.99
-
BrewBuilt® Stainless Butterfly Valve | 2" T.C.
The BrewBuilt Butterfly Valve has all the standard advantages you would expect from a butterfly valve in that they are the most sanitary valve, easy to clean and won't trap wort inside. It has a custom polished stainless steel handle which is designed to fit perfectly with the BrewBuilt X-series conical 2" T.C. bottom port.
$99.99
-
ForgeFit® Stainless Tri-Clamp End Cap | 2.5"
End cap for 2.5" tri-clamp fittings. Made from 304 stainless steel.
$7.99
-
Stainless Steel Camlock - Male Cam x 1.5 in. T.C.
Camlock to tri-clamp adapter. Perfect if you prefer camlock fittings on your tubing lines and own a brewing kettle, pump, or fermenter with tri-clamp fittings. Male camlock fitting x 1.5" tri-clamp. Made from 304 stainless steel. KegLand Part Number: KL20237
$14.49
-
ForgeFit® Stainless Tri-Clamp Extension Tube (Spool) | 1.5" T.C. | 12" Long
304-type stainless steel tri-clamp extension tube with 1.5" clamp ends. 12" long.
$28.99
-
ForgeFit® Stainless Beer Thread Adapter | 5/8" Female Beer Thread x 1.5" T.C.
Convert standard 5/8" beer thread to 1.5" tri-clamp. Made from 304 stainless steel.
$16.49
-
BrewBuilt® 1.5" Tri-Clamp Blowoff U Barb
The Blowoff U Barb eliminates tubing kinks by extending over the shoulder of a stainless conical fermenter and directing tubing straight downward. This gives you the advantage of a stainless steel blowoff cane, but is much easier to clean and sanitize. The 5/8" OD barb is perfect for forming a tight seal with 1/2" ID silicone tubing. Measures approximately 4" from T.C. to barb. 1.5" T.C. 5/8" OD barb Made from 304 stainless steel
$29.99 $22.49
-
White Valve Seat for 1.5 in. T.C. Sample Valve
Replacement valve seat for plunger-style 1.5" tri-clamp sample valve. Compatible with FF120.
$6.59
-
Stainless Tri-Clamp Reducer | 3" T.C. x 1.5" T.C.
Stainless steel Tri-Clamp reducer with 3" T.C. and 1.5" T.C. connections.
$32.99 $21.44
-
Gasket for 2in Butterfly Valve
Replacement interior gasket for the H661B 2" Butterfly Valve
$14.49 $12.32
-
Stainless Tri-Clamp Ferrule | 2.5" T.C.
2.5" TC Ferrule is used to weld in a TC connection anywhere you need one! AiSI304 Stainless Steel.
$13.49
-
Stainless - 1.5" Tri-Clamp
Used to connect two tri-clamp fittings together to make a sanitary connection. 304 stainless steel. For 1.5" tri-clamp fittings.
$7.69
-
Flanged Tri-Clamp Gasket | Silicone | 3"
Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections Silicone gaskets have a wide temperature range and are recommended for hot side applications For 3" tri-clamp connections A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both Silicone and EPDM. Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 3" tri-clamp fittings Made from Silicone Temperature rated from -58°F to 446°F KegLand Part Number: KL44813
$2.59
-
Flanged Tri-Clamp Gasket | EPDM | 3"
Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections EPDM gaskets are more resistant to acids and caustic chemicals, and don't show signs of wear as quickly as silicone For 3" tri-clamp connections A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both EPDM and Silicone. EPDM gaskets have a more narrow temperature range than silicone gaskets, but they are more resistant to acids and caustic chemicals. For 3" tri-clamp fittings Made from EPDM Temperature rated from -30°F to 300°F KegLand Part Number: KL45216 Example Image: Updated images coming soon. See the video below to check out the flanged gaskets in action.
$2.59
-
ForgeFit® Stainless Tri-Clamp Hose End | 1" Barb x 1.5" T.C.
This ForgeFit barb hose end is intended for use with 1" professional beverage tubing. This is the same fitting we use on our pre-fabricated beverage hose assemblies. When designing this fitting, we made sure it has all the features we wanted in a barb intended for professional applications. The hose barb has a shoulder to keep the hose from creeping up towards the fitting end. The long barb promotes solid engagement with the hose and the end has a gentle internal taper to transition the product flow smoothly from the fitting to the tubing. 1.5" tri-clamp connection with 1" OD 2.62" long barb. Overall length 3.25". 3A certified 304 stainless.
$32.99
-
ForgeFit® Stainless Tri-Clamp Barb | 1/2" Barb x 3" T.C.
Use this barbed fitting to connect 1/2" ID tubing to a 3" tri-clamp fitting. Works seamlessly with the BrewBuilt X3 Conical's 3" butterfly valve bottom port. Tri-clamp fittings are the gold standard in professional breweries and they've been widely adopted in homebrewing as T.C. kettles, fermenters, and pumps become more widely available. Tri-clamp fittings allow you to make a sanitary connection without any nooks or crannies for contaminants to hide in and they can be cleaned in place. 3" tri-clamp 1/2" OD barb Made from 304 stainless steel
$24.99
-
Stainless Tri-Clamp | 1.5" T.C. x 1" BSP Female
Convert 1" BSP fittings to 1.5" tri-clamp. Made from 304 stainless steel. BSP vs. BSPP BSP (or BSPT) fittings have a tapered thread and require teflon tape to form a seal between the male and female fitting. BSP fittings are generally intended to be used with their counterpart of the same thread type. ONLY 1/2" BSP fittings are compatible with US-standard NPT fittings of the same size. BSPP fittings, on the other hand, have a straight thread, require a gasket seated inside the female fitting to form a seal, and are not compatible with NPT. Kegland Part Number: KL23443
$16.49
-
ForgeFit® Stainless Tri-Clamp Extension Tube (Spool) | 2" T.C. | 7" Long
304-type stainless steel tri-clamp extension tube with 2" clamp ends. 7" long.
$29.99
-
TC Reducers | 3 in. to 1.5 in.
Tri Clamp adapter that goes from a 3" TC to a 1.5" TC.
$25.95
-
1.5 in TC x 1/4 in Flare Stainless Fitting
This fitting converts a 1.5 in. TC to a 1/4 in. male flare. Made from 304 stainless steel
$17.95
-
Stainless Tri-Clamp Ferrule | 3" T.C.
3" TC Ferrule is used to weld in a TC connection anywhere you need one! AiSI304 Stainless Steel.
$14.49
-
Tri-Clamp Gasket | Silicone | 8"
Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 8" tri-clamp fittings Made from Silicone Temperature rated from -58°F to 446°F
$4.99
-
Flanged Tri-Clamp Gasket | Silicone | 8"
Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections Silicone gaskets have a wide temperature range and are recommended for hot side applications For 8" tri-clamp connections A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both Silicone and EPDM. Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 8" tri-clamp fittings Made from Silicone Temperature rated from -58°F to 446°F KegLand Part Number: KL44790
$4.99
-
Flanged Tri-Clamp Gasket | Silicone | 4"
Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections Silicone gaskets have a wide temperature range and are recommended for hot side applications For 4" tri-clamp connections A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both Silicone and EPDM. Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 4" tri-clamp fittings Made from Silicone Temperature rated from -58°F to 446°F KegLand Part Number: KL44806
$2.79
-
Flanged Tri-Clamp Gasket | Silicone | 1.5"
Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections Silicone gaskets have a wide temperature range and are recommended for hot side applications For 1.5" tri-clamp connections Flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both Silicone and EPDM. Silicone gaskets have a much wider temperature range than EPDM gaskets and are recommended for hot side applications. They are less resistant to acids and caustic chemicals, and may show signs of wear faster than EPDM gaskets. For 1.5" tri-clamp fittings Made from Silicone Temperature rated from -58°F to 446°F KegLand Part Number: KL44837
$2.19
-
Flanged Tri-Clamp Gasket | EPDM | 8"
Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections EPDM gaskets are more resistant to acids and caustic chemicals, and don't show signs of wear as quickly as silicone For 8" tri-clamp connections A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both EPDM and Silicone. EPDM gaskets have a more narrow temperature range than silicone gaskets, but they are more resistant to acids and caustic chemicals. For 8" tri-clamp fittings Made from EPDM Temperature rated from -30°F to 300°F KegLand Part Number: KL45193 Example Image: Updated images coming soon. See the video below to check out the flanged gaskets in action.
$4.99
-
Flanged Tri-Clamp Gasket | EPDM | 4"
Flanged tri-clamp gaskets extend over the ferrule, holding them securely in place for easy, frustration-free connections EPDM gaskets are more resistant to acids and caustic chemicals, and don't show signs of wear as quickly as silicone For 4" tri-clamp connections A flanged tri-clamp gasket differs from a standard gasket or seal because one half of the flanged gasket extends over the edge of the T.C. ferrule, which holds it more securely in place. This makes the gaskets extremely easy to work with while clamping down connections, and helps you avoid the frustration of fumbling a freshly sanitized gasket onto the floor at the worst possible time. Available in both EPDM and Silicone. EPDM gaskets have a more narrow temperature range than silicone gaskets, but they are more resistant to acids and caustic chemicals. For 4" tri-clamp fittings Made from EPDM Temperature rated from -30°F to 300°F KegLand Part Number: KL45209 Example Image: Updated images coming soon. See the video below to check out the flanged gaskets in action.
$2.79
-
ForgeFit Stainless Tri-Clamp Gasket | EPDM | 3.5"
EPDM gasket for 3.5" tri-clamp connection. Temperature rated from -30°F to 300°F. This gasket is a direct replacement part for the ForgeFit 2" Full Port Ball Valve.
$1.99
-
ForgeFit® Stainless Ball Valve | 2" T.C. | Rebuild Kit
This rebuild kit includes a 3.5" T.C. Gasket and 3mm x 77mm O-ring to aid in the repair of the ForgeFit 2" T.C. Ball Valve. The 3.5" T.C. Gasket requires a food grade grease for assembly with the FF190 Ball Valve.
$5.49
-
ForgeFit® Stainless Tri-Clamp Elbow | 90° | 3" T.C.
This elbow fitting features 3" tri-clamp connections at both ends and is made from high-quality stainless steel. Perfect for pairing with the BrewBuilt X3 Conical's 3" bottom port for routing yeast and trub dumps. 3" tri-clamp 90° bend Made from 304 stainless steel
$76.99 $50.04
-
Stainless Tri-Clamp | 3 Piece | 4" Clamp
This stainless steel tri-clamp features two hinges and folds into three pieces. Some brewers find this style of clamp easier to work with on large equipment that requires a 4" clamp. KegLand Part Number: KL32902
$16.99
-
Tri-Clamp Gasket with Stainless Mesh Screen | 7 Mesh | Teflon | 4"
Teflon gasket with 304 stainless mesh screen for 4" tri-clamp connections. Can be used as a filter screen to trap large particulates passing through T.C. fittings. Often used for distillation to retain activated carbon for filtering neutral spirits or used in pot distillation to retain botanicals in the vapor stream. The screen has a mesh size of 7 which will block particles larger than 2.83mm or 2830 microns. This slightly larger mesh size makes this screen ideal for use in a distillation basket. KegLand Part Number: KL28394
$12.49
-
Tri-Clamp Gasket with Stainless Mesh Screen | 7 Mesh | Teflon | 3"
Teflon gasket with 304 stainless mesh screen for 3" tri-clamp connections. Can be used as a filter screen to trap large particulates passing through T.C. fittings. Often used for distillation to retain activated carbon for filtering neutral spirits or used in pot distillation to retain botanicals in the vapor stream. The screen has a mesh size of 7 which will block particles larger than 2.83mm or 2830 microns. This slightly larger mesh size makes this screen ideal for use in a distillation basket. KegLand Part Number: KL28868
$10.99
-
ForgeFit® Stainless Ball Valve | Full Port | 2" T.C.
This 2" tri-clamp ball valve is full port and completely disassembles for easy sanitation. It is perfect for inserting a mixer into a wine tank or for mixing hops in a beer tank. No tools are required for disassembly. Simply turn the valve to the closed position, remove the 3.5" tri-clamp, remove the bottom thumb screw (drain), and tilt the ball out of the socket by rotating the top towards you. Reassemble in reverse order. Use food safe grease on all surfaces. Note: Take care to not allow fermentation inside the valve. Do not open the valve during fermentation. The drain screw can be removed while the valve is closed to drain the valve. 2" tri-clamp 3.5" T.C. assembly Made from 304 stainless steel
$161.49 $137.27
-
ForgeFit® Stainless Beer Thread Adapter | 5/8" Male Beer Thread x 1.5" T.C.
Convert standard 5/8" beer thread to 1.5" tri-clamp. Made from 304 stainless steel.
$11.99
-
Replacement Reservoir for Tri-Clamp Spunding Valve
Replacement reservoir for 1.5" tri-clamp spunding valve. Compatible with both 1 BAR BrewBuilt model (CON4P36) and 2 BAR MB model (CON4P35-MB).
$18.99
-
Plastic Sight Glass Lens | 3" Tri-Clamp | Transparent T.C. End Cap
This sight glass lens is suitable for use with any 3" tri-clamp ferrule with a 3" clamp and gasket. Made of Polyphenylsulfone (PPSU) which offers the clarity of transparency of glass with a much higher shatter and heat resistance. This is a direct replacement part for the Pro Sight Glass Distillation Lid. PPSU is an excellent choice for components that are exposed to high temperatures (up to 392°F) and corrosive media due to its exceptional chemical resistance, as well as being extremely impact resistant, and with the added benefit of being see-through. KegLand Part Number: KL22071
$14.49
You have seen 144 out of 164 products