Whether you're a professional winery, or are making small batches in your kitchen, hardware parts will be necessary. We offer dozens of hardware parts, from hose clamps to butterfly valves. Any hardware you'll need to make great wine can be found in the categories below!
Wine Making Hardware
Shop By Collection
-
Vinyl Beverage Tubing | Rigid | Draft Line | 5/16 in. ID | 9/16 in. OD
5/16 in. ID Beverage Tubing Technical Specifications: 5/16" line provides .40 lbs of restriction per foot. Ideally pounds of resistance should equal pounds of applied pressure. 5/16" line holds 1/2 of an ounce per foot. Made from PVC.
$2.19
-
Vinyl Beverage Tubing | Rigid | Draft Line | 1/2 in. ID | 3/4 in. OD
1/2 in. ID Beverage Tubing Technical Specifications: 1/2" line provides .025 lbs of restriction per foot. Ideally pounds of resistance should equal pounds of applied pressure. 1/2" line holds 1 1/3 of an ounce per foot. Made from PVC.
$5.89
-
ForgeFit® Stainless Tri-Clamp End Cap | 1.5"
End cap for 1.5" tri-clamp fittings. Made from 304 stainless steel.
$3.99
-
Vinyl Transfer Tubing | Flexible | Racking | 1/2 in. ID | 3/4 in. OD
FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product. Thick wall tubing is recomended for pumping and pressurized systems. For siphoning and transferring liquids, see our thin wall and transfer tubing.
$7.39
-
Rubber Stopper - #11 Solid
#11 stopper - solid. Top diameter 2.17 inches (55 mm), bottom diameter 1.89 inches (48 mm), length 1 inch (25 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. Max. Temperature Rating: 158 °F (70 °C).
$4.69
-
Beer & Gas Tubing Quick Disconnect (QD) - 1/4" Barb x Male Shut-off
These quick disconnects feature 1/4" barbed fittings which can be used with either 3/16", 1/4" or 5/16" line. The quick disconnect functionality is activated by a shrouded thumb latch. The temperature range is -40F to 180F. They can handle a vacuum to 120 psi - so you need not worry about them leaking gas. The internal valve spring is 316 type stainless steel and the o-ring is food grade buna-n. For the female side, see our H550B.
$9.99
-
1.5 in. TC x 1.5 in. Barb (Long Stem)
Convert 1.5" Tri-Clamp to 1.5" Barb for connection of 1.5" ID tubing. 304-type stainless steel. 4.5" long stem. This long barb is the perfect TC fitting for banded brewery hoses.
$21.99
-
Stainless Ball Valve - 1/2" Full Port
304 Stainless steel, full port, two piece ball valves that will last for years. Easy to clean with 1/2" FPT on input and output.. High grade 304-stainless made to last with1000psi rating. We've been selling these same valves from the same manufacturer for over 10 years. This is non-locking valve meaning that it does not come with the locking clip. Many users prefer this because you are not constantly lifting the clip to open and close the valve. If you would prefer a ball valve with a locking clip please see the Brewbuilt Ball Valve. TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and the two PTFE gaskets that form the seal when closed.
$17.99
-
Rubber Stopper - #3 With Hole
#3 stopper - with 3/8 inch hole. Top diameter 0.95 inches (24 mm), bottom diameter 0.71 inches (18 mm), length 1 inch (25 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole. Max. Temperature Rating: 158 °F (70 °C).
$1.39
-
Two Hole #10 Brewmaster Silicone Stopper
This stopper has two holes and we use it in the production of our #10 stopper thermowell. It features one 3/8" hole and one 1/4" hole. A racking tube or stainless tube can be inserted into the 1/4" hole with the aid of some lubrifilm, forming an airtight seal, and the 3/8" hole fits an airlock. Even after you wedge all these fittings into it, it still fits a plastic carboy neck! Use this in any configuration you can think of, it'll fit: Airlocks, Thermowells, Racking Canes, and anything else you can imagine!
$5.99
-
CellarScience® Universal Breathable Bung | Wine Barrels
Effortless Bung Removal: The ridge design ensures easy and hassle-free removal of the bung, simplifying barrel management. Effective Airlock System: Acts as an airlock, allowing CO2 to escape while keeping oxygen out, making it perfect for fermentation processes. Versatile Fit: Compatible with 30- and 60-gallon barrels, Variable Volume tanks, and 2" tri-clamp ferrules, offering flexibility across various setups. Multi-Size Replacement: Replaces stopper sizes #10, #11, and #12, with precise measurements for a perfect fit and easy assembly. We recently discovered this premium breathable silicone barrel bung and were immediately impressed with its robust design and features. To start with, the ridge really helps make bung removal effortless. The bung acts as an airlock and allows the release of CO2 while maintaining a seal against oxygen coming in. This makes the bung ideal for alcoholic or malolactic fermentation in barrels or tanks. Fits 30- and 60-gallon barrels as well as the hole in the lid of most Variable Volume tanks! Also fits perfectly in a 2" tri-clamp ferrule Replaces Stopper Sizes #10 , #11, #12 Stopper Measurements: 1.65" x 2.19" (42 mm x 55.5 mm) The flapper stopper protrudes roughly 2.5" from the stopper to allow for easy assembly Other available sizes include the Breathable Carboy Bung and the Universal Breathable Bung. All three size options can be purchased in one complete bundle with the Breather Bung Pack.
$10.99
-
Vinyl Transfer Tubing | Flexible | Racking | 7/16 in. ID | 9/16 in. OD
FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product. 7/16 inch ID tubing is recomended for use with 1/2 inch Auto Siphons. Thin wall tubing is recomended for siphoning and transferring liquids. For pumping, keg lines, or other pressurized applications, see our thick wall and keg tubing.
$4.19
-
Stainless - T.C. Clamp (2.5 in)
Used to connect two tri-clamp fittings together to make a sanitary connection. 304 stainless steel. For 2.5" tri-clamp fittings.
$10.99
-
ForgeFit® Stainless Tri-Clamp Rotating Racking Arm | 1.5"
Stop leaving clean, perfectly good, wine or beer in your tank and always drain from the perfect height with our tri-clover style rotating racking arms. Remove your existing tri-clamp butterfly valve and place this rotating racking arm between the tank and your valve. When it is time to rack off slightly loosen the clamp nearest the tank and use the built-in handle to rotate to just about the lees level. A white rotatable gasket is placed between the welded in tank fitting and this rotating arm. Because the micro finish of the gasket is hard and slippery it allows the rotating arm to rotate in place. A standard black EPDM gasket is placed between the rotating arm and the butterfly valve and is always kept completely tightened. The length of the arm after the elbow is 10.5" allowing you to draw from roughly 8" above or below the valve level. The arm measures 9.5" from the TC fitting to the elbow. We suggest you assemble the rotating arm and butterfly valve in such a way that the arm is pointed in the same direction as the handle on your butterfly valve. In this manner you always know how the racking arm is positioned in your tank. Manufactured from 304-type stainless steel with a polished finish. 1.5" tri-clover connection.
$137.49
-
ForgeFit® Stainless Tri-Clamp | 2" Clamp
The most popular choice for sanitary connections, tri-clamp fittings are widely used in the food & beverage industry due to their ability to be cleaned in place. Tri-clamps join two fittings together without any nooks or crannies for contaminants to hide. Use anywhere you want to ensure a sanitary connection. 2" tri-clamp Made from 304 stainless steel
$10.99
-
Rubber Stopper - #8 With Hole
#8 stopper - with 3/8 inch hole. Top diameter 1.59 inches (40.5 mm), bottom diameter 1.31 inches (33 mm), length 1 inch (25 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole. Max. Temperature Rating: 158 °F (70 °C).
$2.69
-
Vinyl Beverage Tubing | Rigid | Draft Line | 1/4 in. ID | 1/2 in. OD
1/4" is used in beer lines that are 10-25' in length. It is also used as gas line when you want a really tight fit, particularly with homebrew quick disconnects. Soak 1/4" line in hot water before atttaching to larger 5/16" fittings. Technical Specifications: 1/2" Outer Diameter. 1/4" line provides .65 lbs of restriction per foot. Ideally pounds of resistance should equal pounds of applied pressure. 1/4" line holds 1/3 of an ounce per foot. Made from PVC.
$2.19
-
Female Stainless Steel Quick Disconnect (QD) w/Barb
Made in the USA from 304 stainless steel. This quick disconnect seals up very well without a lot of work in connecting them. This will work with any of our H503 and H507 series of quick disconnects. However, it does not work in conjunction with any of our plastic or brass quick disconnects. These feature a 1/2" Barb on the ends for easy connectivity to any 1/2" tubing you may have. The quick disconnect will hold pressure for typical brewing applications when moving liquids at 60psi or less. 3/8" ID. Gasket temperature range is -40° to 250° F. Open port, does not have shut-off. We designed the original stainless QD's for the brewing industry over 10 years ago. The same manufacturer has been machining them for us ever since. The design has certainly been copied but not with consistent quality. That is why our Stainless QD fittings have a near unanimous 5 star review. Please Note: This product will NOT work with our Brass or Plastic Quick Disconnects.
$18.99
-
Stainless - 1.5" TC x 3/4" MPT
Adapt any 3/4" female pipe thread (FPT) fitting to 1.5" TC. AISI304 stainless.
$17.99
-
ForgeFit® Tri-Clamp Gasket | Teflon | 1.5"
Teflon gasket for 1.5" tri-clamp connection. Temperature rated from -100°F to 500°F.
$2.99
-
ForgeFit® Stainless Tri-Clamp Barb | 3/4" Barb x 1.5" T.C.
Convert 1.5" tri-clamp to 3/4" barb for connecting 3/4" ID tubing. Made from 304 stainless steel.
$22.49
-
ForgeFit® Stainless Tri-Clamp Barb | 1" Barb x 1.5" T.C.
Convert 1.5" tri-clamp to 1" barb for connecting 1" ID tubing. Made from 304 stainless steel.
$22.49
-
Male Stainless Steel Quick Disconnect (QD) w/Barb
Made in the USA from 304 stainless steel. This quick disconnect seals up very well without a lot of work in connecting them. This will work with any of our H503 and H507 series of quick disconnects. However, it does not work in conjunction with any of our plastic or brass quick disconnects. These feature a 1/2" Barb on the ends for easy connectivity to any 1/2" tubing you may have. The quick disconnect will hold pressure for typical brewing applications when moving liquids at 60psi or less. 3/8" ID. Open port, does not have shut-off. We designed the original stainless QD's for the brewing industry over 10 years ago. The same manufacturer has been machining them for us ever since. The design has certainly been copied but not with consistent quality. That is why our Stainless QD fittings have a near unanimous 5 star review. Please Note: This product will NOT work with our Brass or Plastic Quick Disconnects.
$13.49
-
ForgeFit® Stainless Sample Valve | 1.5" T.C.
Plunger-style sample valve with 1.5" tri-clamp connection and 1/2" barb. Made from 304 stainless steel.
$37.99
-
Stopper - #12 With Hole
#12 natural latex rubber stopper with 3/8 inch hole. To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole. Top diameter 64 mm, bottom diameter 54 mm, length 27 mm
$10.99
-
Rebuild Kit | O-Rings | Corny Keg
Includes two gaskets for the dip tubes, two for the body connects and one for the lid o-ring. Any keg that has been used for soda in the past should have its gaskets replaced because the soda flavor can never be removed from the rubber. These kits work for Ball lock and most Pin lock kegs.
$4.39
-
Airlock - 3 Piece (XL)
Extra large 3-piece airlock that can hold 50% more sanitizer or water than the standard size (FE370). For both carboys and buckets. In our opinion, 3-piece airlocks are superior to the triple ripple type in that they can be taken apart and cleaned. However, we do sell the triple-ripple (or S-Shaped) type airlock (FE371), in case that's your preference. Please Note: Stopper Not Included.
$3.49
-
Taprite Dual Gauge CO2 Regulator | High Performance Primary Regulator | 0-50 PSI Working Pressure | CGA320 Inlet | One Way Shutoff Valve | 5/16" Barb Outlet
The Taprite is our favorite dual-gauge regulator on the market. We've used them all and this unit represents the best quality at a great price. Key features are the easy hand adjusted pressure adjustment dial, barbed outlet, one way on/off valve, and built in tank connection gasket. Best of all is the consistent pressure regulation. With many regulators the pressure can 'creep' up over time. This unit is a rock. This is the T742HP model where the HP stands for high performance. Won't freeze up when multiple taps are running at once. The built-in gasket where the regulator connects to the CO2 tank, eliminates the constant replacement of fiber washers every time you change out your tank. The one way valve keeps beer from flowing back into the regulator when a keg happens to have more pressure than your regulator is pushing. Hand dial is easily turned to adjust pressure without the need for a screw driver. Optional available gauge cage is the best on the market. Low Pressure gauge reads from 0 to 60 psi. Built by Taprite, an American company. General Regulator Information A regulator controls the flow of CO2 gas that is under pressure. To ensure proper operation, please make sure that when in use your CO2 tank and regulator remain in an upright position. Do not physically modify the regulator in any way. Regulators work best at room temperature. If you use your regulator in the cold it will take up to 4 hours for the adjustment to register. For example: If you are at 10 PSI and you change the pressure to 12 PSI the regulator will move to 14 or 15 PSI over the next 4 hours. Once you have found the correct pressure the regulator will work perfectly fine but it will take some trial and error to get it adjusted. More Tips & Tricks: Are you out of CO2? When the needle reads half way in the red you are about 10% full. You should be able to push another 2-3gallons of beer when your at this amount of remaining gas. What is an ideal serving pressure? For most beers a pressure set at 10-12PSI is the sweet spot. Your beer has to be stored cold from 34-40F for this pressure to work properly. Is your beer serving a lot of foam? Don't panic this is not hard to fix. Your beer line must be 5-8 feet in length for this to work. Turn the black check valve to the close position (as pictured). Release the pressure from your keg's relief valve. Lower the pressure to 6-8psi by turning the flat head screw on the front of the regulator counter clock wise. Open the black check valve releasing CO2 to your keg. Try serving your beer. Is my beer over carbonated? Any beer that is stored under pressure above 12psi will become overcarbonated. If you're trying to speed up the process to carbonate your beer by raising your pressure anywhere from 15-20psi make sure you don't leave your beer at this pressure for more than 2-3 days. If you did this you will need to release all the pressure from the keg before serving and set your serving pressure at 4-6psi depending the carbonation of your beer. After a week you will have to raise your pressure back to the optimum 10-12psi serving pressure.
$87.99
-
BrewBuilt® Stainless Ball Valve | 1/2" Locking Full Port
This BrewBuilt Stainless Steel Ball Valve features a locking mechanism that keeps the valve from being opened by a child or passing dog while you are brewing. Easy to clean 2 piece design, constructed from high grade 304-stainless made to last. 1/2" FPT on input and output side. TIP: You can take a ball valve apart using two crescent wrenches. This will allow you to open up the valve to get to the ball and the two PTFE gaskets that form the seal when closed. Features: 1/2" FPT on inlet and outlet Locking Mechanism on Handle 304 SS construction with PTFE gaskets Two-Piece Construction for easy cleaning Full Port design for minimal pressure loss / resistance BrewBuilt: Designed for Brewing, Built to Last.
$14.99
-
MPT Stainless Steel Male Quick Disconnect (QD)
When used with the male QD these quick disconnect seal up very well in either flow direction, without a lot of work in connecting them. This will work with any of our H503 and H507 series of quick disconnects. However, it does not work in conjunction with any of our plastic or brass quick disconnects. These feature a 1/2" Male National Pipe Thread on the ends for easy connectivity to almost anything. The quick disconnect will hold pressure for typical brewing applications when moving liquids at 60psi or less. 1/2" ID. Gasket temperature range is -40° to 250° F. Open port, does not have shut-off. We designed the original stainless QD's for the brewing industry over 10 years ago. The same manufacturer has been machining them for us ever since. The design has certainly been copied but not with consistent quality. That is why our Stainless QD fittings have a near unanimous 5 star review with retail customers. Please Note: This product will NOT work with our Brass or Plastic Quick Disconnects.
$13.49
-
Expansion Stopper
Expansion stopper for sealing beer, wine, and other narrow neck bottles. Simply insert the expansion stopper into the neck of the bottle, press the lever down, and the bottle will hold carbonation and liquids inside. Great for saving a partial bottle of beer or wine while keeping a good seal on the bottle.
$2.49
-
Gauge Cage | For Taprite Regulator | Mounting Bolt & Washer Included
Protect a dual gauge regulator from falls. A very worthy investment. If you are moving your tank around with regulator attached, a gauge cage becomes a necessity. While made by Taprite to work with our D1060 and D1070 Dual Gauge Taprite Regulators, it will also work with most other brands. Mounting bolt and washer included.
$27.99
-
Stainless - 2.5" TC x 2.5" Barb
2.5" Stainless clover clamp x 2.5" Long Barb for hose connection. 304-Type Stainless Steel.
$32.99
-
Vinyl Transfer Tubing | Flexible | Racking | 3/4 in. ID | 1 in. OD
FDA approved food grade tubing for transferring liquids. Made of Vinyl (PVC). Will not impart flavors or odors into your product. Thick wall tubing is recomended for pumping and pressurized systems. For siphoning and transferring liquids, see our thin wall and transfer tubing.
$8.39
-
Superflex Beverage Tubing | Flexible | Draft Line | 3/16 in. ID | 7/16 in. OD
This is premium beverage tubing that stays flexible even when cold. We use to sell a less expensive tubing but we were not satisfied with the performance on our own draft systems. We think it is definitely worth the little extra cost. 3/16" is the best size for most beer lines under 9' in length. Ideally, 5' provides the correct restriction for serving beer in the 8-14 psi range. Technical Specifications: 3/16" line provides 2.2 lbs of restriction per foot. Ideally pounds of resistance should equal pounds of applied pressure. 3/16" line holds 1/6 of an ounce per foot. Made from PVC. 7/16" OD
$1.19
-
Stopper #5-1/2 | 5.5 - With Hole
#5 1/2 natural latex rubber stopper with 3/8 inch hole. Also called a size 5.5. Size: 0.94 - 1.1 inches To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole.
$0.99
-
KegLand Ball Lock Quick Disconnect (QD) | Gas In | Barbed
White, gas in quick disconnect with barb for gas line. Barb is 1/4". 1/4" or 5/16" beverage tubing is recommended for gas line. Tip N' Trick: Sometimes ball lock fittings are a challenge to quick disconnect "on and off" a cornelius keg. We recommend spraying the body connect on the keg first with a sanitizer solution which acts as a lubricant. When applying the ball lock fitting to the body connect, give a twist and turn to make it easier to connect. We've coined this term "Lube and Turn". Kegland Part Number: KL02943
$6.59
-
KegLand Ball Lock Quick Disconnect (QD) | Beverage Out | Barbed
Black, beverage out quick disconnect with barb for beverage line. Barb is 1/4". 3/16" beverage tubing is recommended. Tip N' Trick: Sometimes ball lock fittings are a challenge to quick disconnect "on and off" a cornelius keg. We recommend spraying the body connect on the keg first with a sanitizer solution which acts as a lubricant. When applying the ball lock fitting to the body connect, give a twist and turn to make it easier to connect. We've coined this term "Lube and Turn". Kegland Part Number: KL02950
$6.59
-
Tubing - Reinforced Vinyl (1 in ID)
Reinforced vinyl is food-grade approved up to 158F. Tubing has a max working pressure of 250 PSI. 1" ID
$25.99
-
LinkTech High Temp Plastic Female Quick Disconnect (QD) | 1/2" Barb W/ Shutoff Valve
The LinkTech 60PS Series is a lineup of premium plastic Quick Disconnects. These High Quality QDs are made from medical grade polypropylene, a high-strength plastic that is temperature tolerant 160° (Max!), and can handle pressure ranging from a vacuum to 60 psi. All of the 60PS Series will interconnect, and these units will also work seamlessly (and leaklessly!) with CPC Quick Disconnects of the same internal 3/8” flow path. O-rings are a EPDM Rubber, and internal valve springs are constructed from 316 Stainless steel. This is a Female Socket, which can connect to any H501 Series Male Plug. It has a 1/2" Hose Barb on the other end for attaching any 1/2" ID tubing. This QD is equipped with a shutoff valve. When not connected to another QD, this will not allow any flow. While not quite as bulletproof as our Stainless Steel Quick Disconnects, this lineup does offer a few advantages. These can be set up with Shutoffs, which will prevent flow when disconnected, and can be incredibly useful on Pump or Glycol systems. The pricing of these products is more economical, yet the plastic is still medical grade. All in all, these are a premium lineup of quick disconnects with great features and lots of options. Features: LinkTech brand 60PS Series Equipped with Shutoff Valve Connections: Female Socket Quick Disconnect 1/2" Barb Medical Grade Materials: Body: High-Strength Polypropylene Spring: 316 Stainless Steel O-Ring: EPDM Operating Pressure: Vacuum to 60 PSI Temperature Tolerance: -40 to 280°F (-40 to 138°C) 3/8" Flow Path Interchangeable with CPC - Colder HFC35 Series
$26.99
-
Rubber Stopper - #2 Solid
#2 stopper - solid. Top diameter 0.83 inches (21 mm), bottom diameter 0.63 inches (15.8 mm), length 1 inch (25 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. Max. Temperature Rating: 158 °F (70 °C).
$0.99
-
CellarScience® Universal Breathable Bung | Plastic Carboys
Secure Fit: Designed with a ridge and gentle taper to prevent slipping or being sucked in, ensuring a reliable seal during use. Self-Sealing Vent: Equipped with vent holes that allow air to escape but prevent it from entering the fermenter. Easy Maintenance: Simple to clean and sanitize, making it highly convenient for repeated use. Replaces stopper sizes #8 and #9 This CellarScience Bung has a ridge to keep it from getting sucked in and self-sealing vent holes to let air out but not in. They have a gentle taper, so they don’t slip out during use. They are also very easy to clean and sanitize. Replaces Stopper Sizes #8, #9 Stopper Measurements: 1.36" x 1.89" (34.5 mm x 48 mm) The flapper stopper protrudes roughly 2.5" from the stopper to allow for easy assembly Other available sizes include the Breathable Carboy Bung and the Breathable Barrel Bung. All three size options can be purchased in one complete bundle with the Breather Bung Pack.
$8.79
-
Tubing - Reinforced Vinyl (3/4 in)
This 3/4in ID reinforced vinyl is food-grade approved up to 158F. Tubing has a max working pressure of 150 PSI.
$16.99
-
ForgeFit® Stainless Butterfly Valve | 1.5" T.C.
This 1.5" Tri-Clamp Butterfly Valve features stainless steel construction and 7-position handle. The plastic handle can be rotated 180° for right or left hand operation.
$79.99
-
Rubber Stopper - #7.5 With Hole
#7.5 stopper - with 3/8 inch hole. Top diameter 1.5 inches (39 mm), bottom diameter 1.22 inches (31 mm), length 1 inch (25 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole. Max. Temperature Rating: 158 °F (70 °C).
$2.59
-
Rubber Stopper - #10.5 With Hole
#10.5 stopper - with 3/8 inch hole. Top diameter 2.09 inches (53 mm), bottom diameter 1.78 inches (45 mm), length 1 inch (25 mm). BPA-free stopper made of food grade materials. Injection molded TPE for superior consistency throughout. Perfect for use with carboys, as the material sticks well to glass and PET, even when wet. To create a solid stopper, simply use a #000 solid stopper (FE400) to plug the hole. Max. Temperature Rating: 158 °F (70 °C).
$4.49
-
Stainless Hex Nipple - 1/2 in. x 1 3/4 in. Threaded
An excellent upgrade to a standard nipple, These have a hex nut in the center to allow easy tightening and loosening in whatever application it's used! Max pressure rating of 150 psi.
$5.49
-
Hose Clamp | 1-1/4" to 2-1/8" OD Tubing Clamp | Flathead Adjustment Screw | Stainless Steel
A heavy duty hose clamp for large OD tubing. As effective as a pre-formed clamp but without the expense or permanence.
$2.99
You have seen 96 out of 534 products