Cornelius Kegs & Parts
-
Rebuild Kit | O-Rings | Corny Keg
Includes two gaskets for the dip tubes, two for the body connects and one for the lid o-ring. Any keg that has been used for soda in the past should have its gaskets replaced because the soda flavor can never be removed from the rubber. These kits work for Ball lock and most Pin lock kegs.
$4.39
-
KegLand Ball Lock Quick Disconnect (QD) | Gas In | Barbed
White, gas in quick disconnect with barb for gas line. Barb is 1/4". 1/4" or 5/16" beverage tubing is recommended for gas line. Tip N' Trick: Sometimes ball lock fittings are a challenge to quick disconnect "on and off" a cornelius keg. We recommend spraying the body connect on the keg first with a sanitizer solution which acts as a lubricant. When applying the ball lock fitting to the body connect, give a twist and turn to make it easier to connect. We've coined this term "Lube and Turn". Kegland Part Number: KL02943
$6.59
-
KegLand Ball Lock Quick Disconnect (QD) | Beverage Out | Barbed
Black, beverage out quick disconnect with barb for beverage line. Barb is 1/4". 3/16" beverage tubing is recommended. Tip N' Trick: Sometimes ball lock fittings are a challenge to quick disconnect "on and off" a cornelius keg. We recommend spraying the body connect on the keg first with a sanitizer solution which acts as a lubricant. When applying the ball lock fitting to the body connect, give a twist and turn to make it easier to connect. We've coined this term "Lube and Turn". Kegland Part Number: KL02950
$6.59
-
Gas Tubing Assembly - Ball Lock Quick Disconnect (QD) - 5/16 in.
Includes ball lock gas-in quick disconnect (barb), 5 ft of 5/16" ID tubing, and two hose clamps.
$14.99
-
Beer Line Assembly with Quick Disconnect (QD)
Includes ball lock beverage-out quick disconnect (barb), 5 ft of 3/16" tubing, hand held faucet, and two hose clamps.
$15.99
-
Flare Fitting - Washer
You will need this washer anytime you connect flare fittings, except when connecting to our quick disconnects which include a built in washer.
$0.49
-
1/4" Nut & 5/16 Barb
This is a special 1/4" nut and 5/16" barb that will attach to threaded quick disconnects or other 1/4" male flare fittings and allow 5/16" gas tubing to be attached. Stainless Steel barb with a chrome plated Brass nut.
$4.99
-
CMBecker Ball Lock Quick Disconnect (QD) | Gas In | Flared | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA
This is a high quality plastic quick disconnect made by CM Becker for your gas line. Flare is 1/4" Tip N' Trick: Sometimes ball lock fittings are a challenge to quick disconnect "on and off" a cornelius keg. We recommend spraying the body connect on the keg first with a sanitizer solution which acts as a lubricant. When applying the ball lock fitting to the body connect, give a twist and turn to make it easier to connect. We've coined this term "Lube and Turn".
$7.29
-
Cornelius Poppet | Common | Corny Keg Part
These poppets are the most common poppets that we sell and will fit nearly every used keg that we sell.. Technically it is for Cornelious brand "Spartan" and "Super Champion" kegs. This poppet will also fit Cornelius brand Pin Lock "R" kegs. Each keg uses two poppets.
$6.99
-
CMBecker Ball Lock Quick Disconnect (QD) | Beverage Out | Flared | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA
This is a high quality plastic quick disconnect made by CM Becker for your beverage line. Flare is 1/4" Tip N' Trick: Sometimes ball lock fittings are a challenge to quick disconnect "on and off" a cornelius keg. We recommend spraying the body connect on the keg first with a sanitizer solution which acts as a lubricant. When applying the ball lock fitting to the body connect, give a twist and turn to make it easier to connect. We've coined this term "Lube and Turn".
$7.29
-
Cornelius Keg Lid (New)
We love these keg lids as either a replacement or an upgrade to the stock lid featured on many homebrew kegs. Most homebrew kegs feature a straight, parallel bale that sits extemely close to the lid when in the closed position. So close that it can be hard to get a finger or two under the bale to open it. The arms on this lid bend outward creating a nice, easy-to-grip handle to open and close the bale. For use with Torpedo, Cornelius, and Firestone kegs. Comes with a pull-ring pressure relief valve and o-ring. PRV rated to 85 psi.
$19.99
-
Corny Keg Lid O-Ring | Silicone | Corny Keg Part
Round silicone O-rings for Cornelius keg lids.
$4.39
-
Replacement PRV | Pull Ring Pressure Relief Valve | Gray | 100 PSI
The most common relief valve. Fits most Cornelius and Firestone style kegs. Long body with spring with gray top and pull ring. Max. pressure rating: 100 psi Kegland Part Number: KL03070
$8.79
-
CMBecker Ball Lock Quick Disconnect (QD) | Gas In | Barbed | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA
This is a high quality plastic quick disconnect made by CM Becker for your gas line. Barb is 1/4". 1/4" or 5/16" beverage tubing is recommended for gas line. Tip N' Trick: Sometimes ball lock fittings are a challenge to quick disconnect "on and off" a cornelius keg. We recommend spraying the body connect on the keg first with a sanitizer solution which acts as a lubricant. When applying the ball lock fitting to the body connect, give a twist and turn to make it easier to connect. We've coined this term "Lube and Turn".
$7.29
-
Gasket | Dip Tubes | Corny Keg Part
Slide gasket onto dip tube and then place dip tube back in keg. 5/16" ID with a 7/64" cross section. Made of FDA BUNA N
$0.49
-
Torpedo Keg | Ball Lock Keg | Stainless Steel Corny Keg | Low2 Keg Lid O-Ring | Superior Oxygen Barrier Properties
Due to high demand, some of these items are currently out of stock but available for pre-order. Please check status notes below when selecting a size option to see if it is In Stock or tagged as PreBook. We will automatically ship this to you when we receive more inventory. Brand new, all-stainless construction ball lock keg Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Set your sights on a brand new Torpedo Keg! The patented, D794,899, sleek all-stainless design represents the pinnacle of quality in ball lock homebrew kegs. With features like welded stainless handles, the ability to stack with fittings in place, amazing quality and a great price we think these kegs will become the standard by which other kegs are measured. Quality First The first thing we at MoreBeer! check out is interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. These kegs are machine welded and exceed our standards for quality. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. In and Out is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Taking your keg on the go? Don't leave home without a custom fitted Torpedo Keg Sleeve! Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions: Height (in.) Diameter (in.) 1.5 Gal 10.25 9 2.5 Gal 14.75 9 5 Gal 23 9 Please Note: These are about 1/2" wider than standard Ball Lock Cornelius Kegs. Need something a bit slimmer? Check out our lineup of Slimline Torpedo Kegs!
$119.99
-
Megamouth Torpedo Keg | Ball Lock Keg | Stainless Steel Corny Keg
The Megamouth Torpedo Kegs are by far the easiest to clean and maintain out of any ball lock homebrew keg you'll find. With an extra-large lid opening, even the buffest of homebrewer (we hear they do exist!) will have no trouble reaching in for a good scrub when it kicks—no expensive keg washing contraptions needed! The Megamouth makes for an excellent pressurizable fermentation vessel and is the ideal choice for brewers who prefer to add dry hops and other flavoring ingredients directly to the keg. The brand new patented design, D794,899, of the Torpedo Keg gives you a high quality keg with features that a dedicated home brewer will appreciate. The machine welds on the Torpedo Keg exceed our standards for quality. There are no nooks and crannies for contaminant to get lodged in. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer. These kegs can be stacked on top of each other with the Ball Lock quick disconnects still attached. They feature rolled stainless steel handles that are comfortable to grab. "In" and "Out" are etched near the keg posts for a quick and mistake-free set up when you are connecting lines in a refrigerator or kegerator. Considering the price and quality, the Torpedo Keg is an amazing value! Mouth opening is 5.8" L x 4.8" W. Dimensions: Height (in.) Diameter (in.) 3 Gal 13.4 11.4 5 Gal 17.9 11.4 6 Gal 20.5 11.4 10 Gal 30.3 11.4
$169.99
-
KegLand Ball Lock Quick Disconnect (QD) | Gas In | Flared
White, gas in quick disconnect with male flare fitting made for Cornelius type kegs. 1/4 inch male flare (MFL) threaded fittings make it easy to connect a variety of hardware pieces and connectors. MFL fittings are more versatile than barbed fitting, but they must be tightened down properly or they can leak. Barbed fittings are also available. Kegland Part Number: KL02967
$6.59
-
KegLand Ball Lock Quick Disconnect (QD) | Beverage Out | Flared
Black, beverage out quick disconnect with male flare fitting made for Cornelius type kegs. 1/4 inch male flare (MFL) threaded fittings make it easy to connect a variety of hardware pieces and connectors. MFL fittings are more versatile than barbed fitting, but they must be tightened down properly or they can leak. Barbed fittings are also available. Kegland Part Number: KL02974
$6.59
-
CMBecker Ball Lock Quick Disconnect (QD) | Beverage Out | Barbed | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA
This is a high quality plastic quick disconnect made by CM Becker for your beverage line. Barb is 1/4". 3/16" beverage tubing is recommended. Tip N' Trick: Sometimes ball lock fittings are a challenge to quick disconnect "on and off" a cornelius keg. We recommend spraying the body connect on the keg first with a sanitizer solution which acts as a lubricant. When applying the ball lock fitting to the body connect, give a twist and turn to make it easier to connect. We've coined this term "Lube and Turn".
$7.29
-
KegLand Ball Lock Quick Disconnect (QD) | Beverage Out | Stainless Steel | Flared
This is a ball-lock type quick disconnect that is constructed from stainless steel for lifetime longevity. This product is for the Black Beverage Out connection on the right, for the White Gas In connection, see our KEG734. 2 1/8" H Please note: the outer bushing on the disconnect is made from chrome-plated brass. All parts that come into contact with liquid are stainless. Kegland Part Number: KL03018
$18.99
-
5 Gal CoolBrew Corny Keg Cooler
Keep your kegs insulated with the new CoolBrew Keg Coolers. Specifically built for Cornelius kegs, these jackets will preserve your precious brew for longer when you take a keg out to share with friends. They come a little oversized to give you extra room for ice or ice packs. This one is perfectly sized for 5 gallon Cornelius kegs. Features: Made from durable polyester Comes with a shoulder strap for easy transport Insulation can keep kegs cold for hours Zipper on top provides easy access to tap and QDs 100% waterproof 26.5 in. Tall x 12 in. Diameter
$59.99
-
Curved Dip Tube | Beverage Out | Ball Lock Kegs Only | Corny Keg Part
For Cornelius style ball lock kegs with curved dip tube. Stainless Steel.
$16.49
-
Torpedo Keg | Ball Lock Keg | Stainless Steel Corny Keg | 15 gal.
The newest addition to the Torpedo Keg arsenal! This ball lock keg has the same great features and superior quality as its predecessors, and will allow large-scale homebrewers to fit their entire batch into a single keg. These kegs are laser welded by an ISO certified commercial keg manufacturer, so you won't find any nooks or crannies for contaminants to hide. Made with rolled stainless steel handles that are comfortable to grab. "In" and "Out" are etched near the keg posts for a quick and mistake-free set up when connecting lines in a refrigerator or kegerator. The 10 and 15 gallon kegs can be stacked on top of each other with ball lock fittings still attached. Considering the price and quality, this Torpedo Keg is an amazing value! Specifications: Total Capacity: 15.2 gal. Max Pressure: 130 psi PRV Rating: 85 psi Height: 24.75" Diameter: 16.05" Made from 304 Stainless Steel
$269.99
-
Torpedo Keg Sleeve
Neoprene keg sleeves for standard Torpedo Kegs. For the Slimline series sleeves, see KEG651. 6mm thick. The 5-gallon sleeve is also compatible with 1/6 bbl or sixtel commercial sanke kegs.
$19.99
-
Gaskets | Body Connect | Corny Keg Part
The gaskets on the body connects that the ball or pin lock fittings slide over. 7/16" ID with a 3/32" cross section. Made of FDA BUNA-N rubber. We also use this as a replacement for the smaller compression ring in our 1/2" Compression fittings so that you can create a snug fit in a Sanke keg conversion kit without permanently compressing a ring on the pick up tube.
$0.99
-
Slimline Torpedo Keg Sleeve
Neoprene keg sleeves for Slimline Torpedo Kegs. For the standard size Torpedo keg sleeves, see KEG650. Also compatible with standard cornelius kegs. 6mm thick.
$19.99
-
Dip Tube | Gas In | Corny Keg Part
For the gas in side. Stainless steel construction, approximately 1.5" in length.
$5.49
-
Torpedo Cocktail Keg | US D-Style Spear | Stainless Steel Keg | Low2 Keg Lid O-Ring | Superior Oxygen Barrier Properties
The ideal vessel for serving pre-mixed cocktails and other concoctions on draft Easily pour in your beverage of choice through the wide corny-style lid opening without needing to remove the spear Doubles as a line cleaning keg Rolled handles for a comfortable grip Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams The Torpedo Cocktail Keg is the ideal vessel for serving pre-mixed cocktails and other concoctions on draft. The corny keg style lid makes it easy to pour in your beverage of choice without having to fuss with removing the spear like with standard commercial sanke kegs. Hook up a D-Style keg coupler to begin carbonating the beverage from the bottom up. These kegs provide the added advantage of fully carbonating the entire cocktail. When making drinks on the fly, carbonation is lost quickly since you're mixing carbonated and still ingredients together. But when served from a fully carbonated keg, you can enjoy the bubbles in your glass for longer! Draft lines needing some love? The Torpedo Cocktail keg easily doubles as a line cleaning keg. Simply fill with a batch of LLC or BLC to give your bev lines a little TLC. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions: Height (in.) Diameter (in.) 1.5 Gal 10 9 3/8 2.5 Gal 13 1/4 9 3/8
$179.99
-
Slimline Torpedo Keg | Ball Lock Keg | Stainless Steel Corny Keg | Low2 Keg Lid O-Ring | Superior Oxygen Barrier Properties
The Slimline Torpedo Keg series features a smaller diameter to maximize the space in your kegerator or keezer Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Brand new, all-stainless construction ball lock keg Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Torpedo Kegs too wide? Want to squeeze another keg in your kegerator? The patented design, D794,899, of the Slimline Torpedo Keg is 9% more slim than the classic model with all the same great features. Coming in at about 1/4" thinner than standard Ball Lock Cornelius Kegs, this keg has welded stainless handles and the ability to stack kegs with fittings still in place all at a great price. Quality First Here at MoreBeer! we love nothing more than quality interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. Torpedo kegs are machine welded and exceed our standards for quality. This weld quality is possible because these kegs are made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. “In” and “Out” is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Taking your keg on the go? Don't leave home without a custom tailored Slimline Torpedo Keg Sleeve! Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions: Height (in.) Diameter (in.) 1.5 Gal 11 8 3/8 2.5 Gal 15 5/8 8 3/8 5 Gal 25 1/2 8 3/8 For a slightly shorter keg, see our Standard Torpedo Kegs!
$119.99
-
Beverage Jumper Line - Ball Lock Quick Disconnect (QD)
Push product or sanitizer from one keg to the next. Two black, beverage quick disconnects with flare fittings attached via a one foot piece of beverage line.
$17.99
-
Torpedo Keg | Ball Lock Keg | Stainless Steel Corny Keg | Low2 Keg Lid O-Ring | Superior Oxygen Barrier Properties | 15 Gallon
Super-sized corny keg, great for bigger batches and fermentation Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Has the size and strength of a 15.5-gal commercial keg with the easy to open/clean/fill of a homebrew keg Brand new, all-stainless construction ball lock keg Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Look out below! The Torpedo Keg Depth Charge series just dropped and they're set to send blast waves through the homebrew world. Large-scale homebrewers will appreciate the ability to fit their entire batch into a single 15-gallon ball lock keg, and you can expect the same great features that have made Torpedo Kegs such a hit. Laser welded construction for superior quality, rolled stainless steel handles that will last a lifetime, and stackable design that won't interfere with your fittings. Quality First The first thing we at MoreBeer! check out is interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. These kegs are machine welded and exceed our standards for quality. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving, which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. In and Out is etched near the keg posts for easy identification, which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Specifications: Total Capacity: 15.2 gal. Max Pressure: 130 psi PRV Rating: 85 psi Height: 24.75" Diameter: 16.05" Made from 304 Stainless Steel
$239.99
-
Ball Lock Post Bulkhead - Gas In
This gas in ball lock bulkhead assembly allows you to add a ball lock post just about anywhere. Create your own pressure vessel or attach it to one of our aluminum gas manifolds for a quick connect option. 1/4" BSP threads and locking nut. Kegland Part Number: KL03179
$14.49
-
KegLand Ball Lock Quick Disconnect (QD) | Gas In | Stainless Steel | Flared
This is a ball-lock type quick disconnect that is constructed from stainless steel for lifetime longevity. This product is for the White Gas In connection on the left, for the Black Beverage Out connection, see our KEG732. 2 1/8" H Please note: the outer bushing on the disconnect is made from chrome-plated brass. All parts that come into contact with liquid are stainless. Kegland Part Number: KL03001
$18.99
-
Ball Lock Post Bulkhead - Bev Out
This bev out ball lock bulkhead assembly allows you to add a ball lock post just about anywhere. Use in conjunction with the gas in bulkhead to create your own pressure vessel. The included short dip tube can be replaced with a longer dip suitable to your needs. 1/4" BSP threads and locking nut. Kegland Part Number: KL03162
$14.49
-
Pin Lock Socket
We made this socket so that you can easily remove gas and beverage body connects on Pin Lock style kegs. (Currently a 3/8" drive)
$29.99
-
Body Connect - Pin Lock Quick Disconnect (QD) Beer Out (3 pins)
Replacement pin lock beverage out body connect for pin lock kegs. Also called a post. Has 3 pins for securely locking a Pin Lock beverage out quick disconnect into place. Does not include poppet. 9/16-18 UNF threads.
$10.99
-
Body Connect - Pin Lock Quick Disconnect (QD) Gas-In (2 pins)
Replacement pin lock gas in body connect for pin lock kegs. Also called a post. Has 2 pins for securely locking a Pin Lock gas quick disconnect into place. Does not include poppet. 9/16-18 UNF threads.
$10.99
-
Keg Lid Foot
The foot for the swing arm on the keg lid. They are often missing on used kegs.
$1.49
-
Low2 Keg Lid O-Ring | Corny Keg Lid O-Ring | Superior Oxygen Barrier Properties
96% reduction in oxygen ingress compared to silicone O-rings when measured in a keg! Made from a special blend of materials, these gaskets offer vastly improved oxygen barrier properties compared to Silicone or EPDM Give your beverage the absolute best protection from oxygen staling with KegLand's Low2 O-rings! The result is your beverage staying fresher for longer! Compatible with any ball lock or pin lock corny-style keg with standard lid Upgrade the storage life of your beer by replacing your standard keg lid O-ring with the new Low2 O-ring from KegLand. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Compatible with any ball lock or pin lock corny-style keg with a standard size lid. Not compatible with Megamouth Torpedo Kegs. Low2 O-rings were independently tested by GunnLab, an Australia-based plastic packaging testing laboratory. See below for a printout of the test results. KegLand Part Number: KL03063
$4.39
-
CMBecker Pin Lock Quick Disconnect (QD) | Gas In | Flared | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA
This is a high quality fitting made by CM Becker in Germany. Red body with gray top. 2 pin. 1/4'' male flare fitting.
$7.99
-
CMBecker Pin Lock Quick Disconnect (QD) | Beverage Out | Barbed | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA
This is a high quality fitting made by CM Becker in Germany. Red body with black top. 3 pin. 1/4'' barb fitting.
$7.99
-
CMBecker Pin Lock Quick Disconnect (QD) | Gas In | Barbed | High-Quality Plastic QD | NSF Registered | Made in Germany | Assembled in USA
This is a high quality fitting made by CM Becker in Germany. Red body with gray top. 2 pin. 1/4'' barb fitting.
$7.99
-
CMBecker Inline Check Valve | Quick Disconnect (QD) | Flared
This inline check valve can be used with any gas-in ball lock or pin lock flared disconnect. Allows gas to flow through while preventing the backflow of liquid. Made in Germany and assembled in the USA by CM Becker.
$9.99
-
Torpedo Keg Dip Tube | Gas In | Corny Keg Part
Replacement Gas In dip tube for Torpedo Kegs. Stainless steel construction, approximately 1" in length.
$3.99
-
Firestone Poppet | Pin Lock | Corny Keg Part
For Firestone brand Pin Lock kegs. Also fits older John Wood pin lock kegs. Each keg used two poppets.
$17.99
-
Gas Tubing Assembly - Pin Lock Quick Disconnect (QD)
Includes pin lock gas in quick disconnect, line and two hose clamps.
$16.99
-
Torpedo Keg | Ball Lock Keg | Stainless Steel Corny Keg | Low2 Keg Lid O-Ring | Superior Oxygen Barrier Properties | 6 Gallon
Oversized corny keg, great for bigger batches and fermentation Low2 lid O-ring reduces oxygen ingress by 96% compared to silicone O-rings when measured in a keg! Brand new, all-stainless construction ball lock keg Stackable with ball lock quick disconnects in place Etched In and Out labels near the keg posts for easy identification Rolled handles for a comfortable grip Made by an ISO certified commercial keg manufacturer with high-quality laser welded seams Set your sights on a brand new Torpedo Keg! The patented, D794,899, sleek all-stainless design represents the pinnacle of quality in ball lock homebrew kegs. With features like welded stainless handles, the ability to stack with fittings in place, amazing quality and a great price we think these kegs will become the standard by which other kegs are measured. Quality First The first thing we at MoreBeer! check out is interior welds. We've spent a decade rejecting kegs made overseas because the interior welds have never met our standards. If a weld is not perfect and shows evident burn marks along with nooks and crannies it cannot be sanitized effectively. These kegs are machine welded and exceed our standards for quality. The weld quality is possible because these kegs made by an ISO certified commercial keg manufacturer. Cool Features Torpedo Kegs were designed to stack with Ball Lock quick disconnects in place and serving which is a cool feature for some brewers who have vertical space in their refrigerator. We also like the rolled stainless steel handles. They are comfortable to grab and will never come off like some rubber handles can over time. In and Out is etched near the keg posts for easy identification which is very handy when you are connecting lines in a refrigerator or kegerator and trying not to make a mistake. Stainless Fermenter We've seen a lot our customers having great success using the 6-gallon Torpedo Keg as a stainless steel fermenter or "kegmenter". The extra headroom that this size offers makes it a great option for fermenting 5-gallon batches. We highly recommend using CellarScience Foam Axe if you're fermenting in the keg. Foam Axe will help reduce krausen buildup, cutting down the chance of clogging issues with the ball lock poppets and the PRV in the keg lid. It should also be noted that leaving your finished beer on the leftover trub from fermentation for too long will eventually lead to off-flavors. If it won't be consumed in 2-3 weeks, transfer your beer to a fresh keg using the Torpedo Keg Buoy which will pick up the clearest beer and leave the sediment behind. Low2 Keg Lid O-ring Give your beverage the absolute best protection from oxygen staling with the Low2 keg lid O-ring. Even the most perfectly sealed keg is susceptible to oxygen ingress through the hatch O-ring—yes, even if the keg is under constant pressure with CO2! Even a leak-free, pressurized keg will release CO2 molecules as they pass through the lid O-ring itself, and conversely, Oxygen molecules will permeate through the O-ring and diffuse into the keg when they reach the surface area on the other side. The level of permeability is wide ranging and highly dependent on what material the O-ring is made from. Rather than the usual EPDM or Silicone, Low2 gaskets are made from a unique composition of Synthetic M-Class and Cross-Link Elastomers. This special blend has superior oxygen barrier properties that results in your beverage staying fresher for longer. Specifications: Max Pressure: 130 psi PRV Rating: 85 psi High Quality Laser Welded Seams ISO9001 Quality Assurance Made from 304 Stainless Steel Dimensions: 27.15" H x 9" D
$159.99
You have seen 48 out of 64 products