Tanks, Regulators & Manifolds

A nitrogren regulator used for Nitrogen and Argon - it will fit both tanks. A nitrogen regulator has a higher high-pressure gauge than a CO2 regulator. (The starting pressure in a Nitrogen/Argon tank will be about 2200 p.s.i. as opposed to 800 p.s.i for a CO2 tank.) CGA580. Tap-Rite brand nitrogen regulator. 5/16" barb. For more information on using gas for flushing vessels, please refer to MoreWine!'s Guide to Inert Gas in Winemaking

Read more less

The Taprite is our favorite dual-gauge regulator on the market. We've used them all and this unit represents the best quality at a great price. Key features are the easy hand adjusted pressure adjustment dial, barbed outlet, one way on/off valve, and built in tank connection gasket. Best of all is the consistent pressure regulation. With many regulators the pressure can 'creep' up over time. This unit is a rock. This is the T742HP model where the HP stands for high performance. Won't freeze up when multiple taps are running at once. The built-in gasket where the regulator connects to the CO2 tank, eliminates the constant replacement of fiber washers every time you change out your tank. The one way valve keeps beer from flowing back into the regulator when a keg happens to have more pressure than your regulator is pushing. Hand dial is easily turned to adjust pressure without the need for a screw driver. Optional available gauge cage is the best on the market. Low Pressure gauge reads from 0 to 60 psi. Built by Taprite, an American company. General Regulator Information A regulator controls the flow of CO2 gas that is under pressure. To ensure proper operation, please make sure that when in use your CO2 tank and regulator remain in an upright position. Do not physically modify the regulator in any way. Regulators work best at room temperature. If you use your regulator in the cold it will take up to 4 hours for the adjustment to register. For example: If you are at 10 PSI and you change the pressure to 12 PSI the regulator will move to 14 or 15 PSI over the next 4 hours. Once you have found the correct pressure the regulator will work perfectly fine but it will take some trial and error to get it adjusted. More Tips & Tricks: Are you out of CO2? When the needle reads half way in the red you are about 10% full. You should be able to push another 2-3gallons of beer when your at this amount of remaining gas. What is an ideal serving pressure? For most beers a pressure set at 10-12PSI is the sweet spot. Your beer has to be stored cold from 34-40F for this pressure to work properly. Is your beer serving a lot of foam? Don't panic this is not hard to fix. Your beer line must be 5-8 feet in length for this to work. Turn the black check valve to the close position (as pictured). Release the pressure from your keg's relief valve. Lower the pressure to 6-8psi by turning the flat head screw on the front of the regulator counter clock wise. Open the black check valve releasing CO2 to your keg. Try serving your beer. Is my beer over carbonated? Any beer that is stored under pressure above 12psi will become overcarbonated. If you're trying to speed up the process to carbonate your beer by raising your pressure anywhere from 15-20psi make sure you don't leave your beer at this pressure for more than 2-3 days. If you did this you will need to release all the pressure from the keg before serving and set your serving pressure at 4-6psi depending the carbonation of your beer. After a week you will have to raise your pressure back to the optimum 10-12psi serving pressure.

Read more less

Protect a dual gauge regulator from falls. A very worthy investment. If you are moving your tank around with regulator attached, a gauge cage becomes a necessity. While made by Taprite to work with our D1060 and D1070 Dual Gauge Taprite Regulators, it will also work with most other brands. Mounting bolt and washer included.

Read more less

Manifolds allow you to have one CO2 tank with multiple lines. Each line can be turned off individually without affecting flow to other kegs. Each ball valve contains a check valve that ensures no beer or gas can flow between the two kegs. The barbs are all 5/16", standard for gas line in the beer industry.

Read more less

Use Nitrogen or Argon for flushing tanks or pushing wine from kegs for topping up barrels or serving Perfect for serving still wine, cold brew coffee, Sangria and premixed cocktails on draft Can be filled with Nitrogen, Argon, or Beer Gas Mix Brand new, high-strength aluminum tank with CGA580 valve Ships empty—fill at a welding shop or swap at your local beer & winemaking supply store Brand new aluminum 22 cubic feet Nitrogen tank made from high strength aluminum alloy and high quality CGA580 valves. Because it is made of aluminum rather than steel you can feel confident that it won’t rust. This is the tank you need for flushing vessels or pushing wine from kegs using either Nitrogen or Argon. Gas flushing is a very useful process for giving added protection to wines by helping to minimize contact with oxygen in your storage containers. Also, wine stored in kegs for either topping up barrels or for serving should be pushed with Nitrogen or Argon rather than CO2 to prevent adding carbonation to your wine (unless you want all your wines to be sparklers!). Generally speaking, we recommend using Argon instead of Nitrogen around your winery, mainly because it is denser than air and so is much more effective when it comes to flushing vessels. Though it is more expensive than Nitrogen, we feel that the added expense is worth it when it comes to protecting our wines. Aluminum tanks are superior to steel because they do not rust. All tanks are shipped empty. To have tanks filled you will want to visit your local welding supply shop. Because you are purchasing a new tank you can choose to either have it filled or to exchange it for a filled tank at your local gas supplier. If you have this tank filled the local gas supplier is responsible for affixing the correct neck label that identifies the gas being put in the cylinder. Tanks should always be stored in an upright position. Features: Made from corrosion resistant, engineered Aluminum Brushed finish Thick, durable cylinder walls DOT approved New high quality CGA-580 valve Light weight compared to steel tanks Rated to 2216 PSI service / 3360 PSI test pressure PSI (allowing for Nitrogen fill) Can also be filled with Argon or Beer Gas Mix (Nitrogen/CO2) NOTE: You will need at Nitrogen/Argon Regulator to go with this tank, a standard CO2 regulator will not work.

Read more less

An inexpensive way to split your co2 gas line to multiple taps. Works with 5/16" tubing best, barbs on this CO2 Tee are 5/16", use hose clamps to secure. A quick tip is to put the end of the tubing in 100-120F water for a minute to soften the tubing. We suggest work gloves when putting tubing onto this product as the ends can be sharp.

Read more less

Replacement CO2 regulator 60 psi gauge for setting dispense pressure. RHT

Read more less

Replacement low pressure gauge for CO2 or Nitrogen regulator - used to determine how much pressure you're allowing out of the regulator. RHT

Read more less

Manifolds are a great way to have one CO2 tank supply multiple kegs. This manifold is made from aluminum, brass, and stainless. It also works up to 100 psi and includes 1/4 in ball valves with built in check valves. Another ball valve can be added to the end of the manifold for an additional gas line. Multiple manifolds can be linked up with a 1/4" nipple (D1820B). Features: 1/4" BSP ball valves 1/4" barbs Rated up to 100 psi Screw holes for easy mounting Optional additional port on the end   SKU Overall Length D1802 5-1/2 in. D1807 7-3/8 in. D1811 9-5/8 in. D1813 11-1/2 in. D1816 13-1/2 in. The above measurements are from the tip of the brass barb to the plug on the opposite end. Each manifold measures approximately 3.5" from the mounting holes to the tip of the valve. Kegland Part number: KL02554

Read more less

Simple Tee's that work great with 5/16" ID tubing. Made in the USA by Kent.

Read more less

The KOMOS gas manifold features 1/4" flare gas inlet and check valves for much more flexibilty when choosing your draft line. Use 1/4" or 5/16" gas line with the appropriate Flare Fitting Set (KEG607 or KEG640), or use EVABarrier Draft Tubing with the appropriately sized Duotight fitting (DUO106 or DUO120). The check valves can also be replaced with a Ball Lock Post Bulkhead, allowing for the use of a gas-in ball lock jumper line as a quick connect option. If more than 4 outlets are needed, join multiple manifolds together with this 1/4" Nipple. Features: 1/4" Flare connections 1/4" BSP ball valves Rated to 100 psi Wall mount holes Made from aluminum, brass, and stainless steel Size Overall Length 2-way 5.25" 3-way 7.25" 4-way 9.25"   The above measurements are from the tip for the brass flare inlet to the plug on the opposite end. Each manifold measures approximately 3.5" from the mounting holes to the tip of the valve.  

Read more less

The Duotight In-Line Regulator works with both gas and liquid. Easily adjust the flow can be adjusted with the yellow adjustment knob. 8 mm Duotight fittings at both inlet and outlet make this unit perfect for use with EVABarrier 8 mm OD tubing (D1717 or D1718).  Features an integrated pressure gauge so you can quickly and easily dial in your pressure setting. The analog gauge is removable and can be swapped out with a gauge of a different pressure range or it can be swapped out for the Digital Mini Pressure Gauge. Stepping Down Pressure The ideal regulation scenario occurs when the inline regulator steps down the output pressure to at least 10 PSI less than the inlet pressure. For example, if the inlet pressure is 30 PSI, the regulator effectively manages a range from 0–20 PSI on the output side ensuring optimal performance and stability. Ideal regulation scenario (10 PSI less than inlet pressure) Example of 30 PSI inlet translating to 0–20 PSI output Specifications: Made from food grade acetal Stainless screws Easily disassembles for cleaning 8mm (5/16") Duotight fittings at both ends Interchangeable pressure gauge Gauge reads from 0-60 psi Made with quality EPDM seals Wall mountable WARNING: Do not exceed gauge pressure. Exceeding the pressure range will damage the gauge. Kegland Part number: KL15035  

Read more less

3000psi gauge tells tank pressure. Left hand thread replacement gauge for some brand regulators.

Read more less

The Duotight In-Line Regulator works with both gas and liquid. Easily adjust the flow can be adjusted with the yellow adjustment knob. 6.35 mm Duotight fittings at both inlet and outlet make this unit perfect for use with 6.35 mm OD tubing (D1723C or D1727C).  Features an integrated pressure gauge so you can quickly and easily dial in your pressure setting. The analog gauge is removable and can be swapped out with a gauge of a different pressure range or it can be swapped out for the Digital Mini Pressure Gauge. The size of the Duotight connection and the extended 0-150 PSI pressure range makes this model perfect for stepping down the pressure of your mains water line for use with water filtration or RO systems. Specifications: Made from food grade acetal Stainless screws Easily disassembles for cleaning 6.35mm (1/4") Duotight fittings at both ends Interchangeable pressure gauge Gauge reads from 0-150 psi Made with quality EPDM seals Wall mountable WARNING: Do not exceed gauge pressure. Exceeding the pressure range will damage the gauge. Kegland Part number: KL26918

Read more less

Replacement knob for Kegland CO2 tanks. Compatible with tanks sized 2.5 - 20 lbs. KegLand Part Number: KL30625

Read more less

20 PSI replacement spring for pressure relief valves.  All SS, works with our D1830, as well as a replacement for our Counter Pressure Bottle Fillers.

Read more less

Brand new aluminum 5 lb CO2 tank made from high strength aluminum alloy and high quality CGA320 valves. Made from corrosion resistant, engineered Aluminum New high quality CGA-320 valve DOT approved Because it is made of aluminum rather than steel you can feel confident that it won’t rust. It’s called a 5 lb tank because it holds 5 lbs of compressed (liquified) CO2. 5 lbs of CO2 is enough to dispense about 8 to 9x 5-gallon kegs of homebrew. Aluminum tanks are superior to steel because they do not rust. All tanks are shipped empty. To have tanks filled you will want to visit your local welding supply shop. Because you are purchasing a new tank you can choose to either have it filled or to exchange it for a filled tank at your local gas supplier. If you have this tank filled the local gas supplier is responsible for affixing the correct neck label that identifies the gas being put in the cylinder. Tanks should always be stored in an upright position. Features: Made from corrosion resistant, engineered Aluminum Brushed finish Thick, durable cylinder walls 18" T x 5.25 Ø DOT approved New high quality CGA-320 valve Light weight compared to steel tanks  

Read more less

Silicone regulator stem o-ring. For regulators such as the D1060 & D1065, which have an o-ring located where the regulator stem mates with the CO2 cylinder. Pack of 2.

Read more less

So you had the great foresight to buy our modular gas line manifold and now you are adding a keg. You need gas on that keg. No problem, use our add on assembly to expand your existing manifold. Includes a shut off check/ball valve, one tee and a connecting nipple.

Read more less

Brand new aluminum 5 lb CO2 tank made from high strength aluminum alloy and high quality CGA320 valves. Because it is made of aluminum rather than steel you can feel confident that it won’t rust. It’s called a 5 lb tank because it holds 5 lbs of compressed (liquified) CO2. 5 lbs of CO2 is enough to dispense about 8 to 9x 5-gallon kegs of homebrew. Aluminum tanks are superior to steel because they do not rust. All tanks are shipped empty. To have tanks filled you will want to visit your local welding supply shop. Because you are purchasing a new tank you can choose to either have it filled or to exchange it for a filled tank at your local gas supplier. If you have this tank filled the local gas supplier is responsible for affixing the correct neck label that identifies the gas being put in the cylinder. Tanks should always be stored in an upright position. Features: Made from corrosion resistant, engineered Aluminum Brushed finish Thick, durable cylinder walls 18" T x 5.25 Ø DOT approved New high quality CGA-320 valve Light weight compared to steel tanks  

Read more less

With this adapter you can use a KOMOS CO2 regulator with a Nitrogen or Argon tank. Not all CO2 Regulators are suitable for use with a Nitrogen tank. Only for use with KOMOS regulator which is a dual gas regulator capable of handling Nitrogen and CO2 gasses.  CGA320 male thread by CGA580 male thread. Compatible with KOMOS Dual Gauge and Dual Body regulators.  

Read more less

3000psi gauge tells tank pressure. Right hand thread replacement gauge for most brands of regulators.

Read more less